Eaton Powerware 5110 User manual

UserÊs Manual 350-1500VA 1

Powerware 5110 UPS

UserÊs manual

UserÊs Manual 350-1500VA

The contents of this manual are the copyright

of the publisher and may not be reproduced (even extracts)

unless permission granted.

Every care has been taken to ensure the accuracy of

the information contained in this manual, but no liability

can be accepted for any errors or omission. The right

to make design modifications is reserved.

UserÊs Manual 350-1500VA 3

Powerware 5110 UPS

UserÊs manual

1023922 Revision A

Contents

Introduction .................................................................................................................. 4

Features .................................................................................................................... 4

Unit inspection .......................................................................................................... 4

Safety Instructions ...................................................................................................... 5

Battery connection required before use! .................................................................... 6

Connecting the Battery: ............................................................................................ 6

Installation and Operation: .......................................................................................... 6

Indicators: .................................................................................................................... 7

Indicator table: ............................................................................................................. 9

Status Indicators ........................................................................................................... 9

LED Indicator Table ................................................................................................... 9

LED Audible Alarm Table............................................................................................ 9

Battery replacement procedure: ................................................................................. 9

Troubleshooting ...................................................................................................... 12

Specification ........................................................................................................... 13

Service and Support .................................................................................................. 14

UserÊs Manual 350-1500VA

Introduction

The Powerware 5110 uninterruptible power system (UPS) filters the input line from

line disturbances and protects your sensitive electronic equipment from five common

power problems such as power failures, power sags and power surges.

Features:

 Processor-controlled voltage regulation (AVR)

 Six outlets

- Three with surge and battery backup protection

- Three with surge protection only

 Data Line (Internet faxmodemDSL) or telephone line surge protection

 Cold Start capability

 USB communication port

 User-replaceable batteries

Unit inspection

Once you have received the Powerware 5110 UPS product, you should remove and

inspect the product for shipping damage. If any damage is found, please notify the

carrier and your dealer. Please keep the shipping carton and the packing foam in the

event the product must be returned to the factory for service.

Eaton Power Quality Pty Ltd

10 Kent Road Mascot NSW 2020

Phone: +61-2-9693 9366

Fax: +61-2-8338 1159

UserÊs Manual 350-1500VA 5

Safety Instructions

ATTENTION

Maintenance, other than battery replacement must be performed by a

qualified technician. Failure to do so could result in an electrical shock.

Although the unit may be unplugged from utility power, hazardous

voltage still may be present through the battery.

1. Place the Powerware 5110 UPS indoors in an area that has adequate airflow and

is free of excessive dust. Do NOT allow the UPS to be exposed to moisture, rain,

excessive heat, or direct sunlight.

2. Use of the Powerware 5110 UPS product in life support applications, where failure

of this equipment can reasonably be expected to cause failure of life support

equipment or to significantly affect its safety or effectiveness is NOT recommended.

3. Shut off the UPS and disconnect the input power cord from the wall outlet before

replacing the battery.

4. When replacing the battery, use the same number and type of battery

5. Do NOT dispose of battery in a fire. The battery may explode.

6. Do NOT open or mutilate the battery. They contain an electrolyte that is toxic and

harmful to the skin and eyes.

7. Proper disposal of the battery is required. Please refer to your local laws/regulations

regarding battery disposal.

8. Use tools with insulated handles to replace the battery to avoid personal injury. Due

to energy hazard, please remove wristwatches and jewelry such as rings when

replacing battery.

UserÊs Manual 350-1500VA

Battery connection required before use!

Connecting the Battery:

Principle shown below. For detailed information how to connect, please refer to battery

replacement section.

Installation and Operation:

The following steps explain how to connect and operate the Powerware 5110 UPS.

1. Connect the UPS to a grounded power outlet.

Note

It is recommended that the battery should be charged for minimum 8 hours

to ensure full charge before placing the UPS in service.

2. Plug your computer, monitor or load to be protected into the „Battery Backup &

Surge Protection‰ outlets. (These outlets will provide emergency battery backup

power during power outages as well as protection from surges and spikes.)

Do NOT plug LASER PRINTERS into the „Battery Backup‰ outlets.

Do NOT plug ACCESSORY SURGE strips into the „Battery Backup‰ outlets.

3. Plug your peripheral equipment or non-critical loads (printer, scanner, fax, speaker,

etc.) into the „Surge Protection‰ outlets. (These outlets provide surge and spike

protection only, they will NOT provide battery backup power during a utility power

failure).

4. Connect your computer to the UPS using USB cable provided.

5. With your equipment turned off, switch on the UPS.

6. When the „On/Off‰ LED light is illuminated, turn on the connected equipment.

7. Install Power management software provided with the UPS

UserÊs Manual 350-1500VA 7

Indicators

1. On/Off Push Button/Test Switch

One switch controls the power to your equipment and performs a self-test to detect

overload or undercharged conditions.

Turn on the UPS

Press and hold the switch for more than one second and release the switch after the

beep. The UPS will start.

Turn off the UPS

Press and hold the switch for more than one second and release the switch. The

UPS will shut down completely.

Perform Self-Test

The UPS will perform self-test for about 4.5 seconds when the UPS is turned on and

the utility power is present.

2. Normal Mode (Green) LED

Indicates the UPS is providing mains power to your

equipment. When the LED is blinking the UPS is

providing power from the battery.

3. Fault (Red) LED

When blinking, LED could indicate an overload

condition or that the battery should be replaced. When

the LED is always on it indicates a short or UPS fault.

For details please see Indicator Table.

4. Battery Mode (Yellow) LED

Indicates the UPS is providing battery power to your

equipment.

UserÊs Manual 350-1500VA

5. 3 Battery Backup and Surge Protection Outlets

These 3 Australian 10 Amp output receptacles

provide full time surge protection, but also

provide emergency battery backup power.

6. 3 Surge Protection Outlets

These 3 Australian 10 Amp output receptacles

provide full time protection from surge and spike.

7. Phone/Modem/ADSL Protection

Built in RJ11 jacks protect the internet, phone

or fax line from surges. Connect the line in from

the wall into the jack named „In‰ and connect

the phone, modem ADSL box to the jack named

„Out‰.

8. USB Communication Port

The provided LanSafe monitoring and shutdown

software can be automatically configured to save

the files and shut down your computer in the

event of a prolonged power outage.

9. Circuit Breaker

The button will protrude when the overload

condition occurs. The UPS will switch off of

utility power. If the button protrudes, disconnect

some non-essential equipment and reset the

circuit breaker by pushing the button inward.

10. Power Connector

10 Amp IEC to 10 Amp Australian input lead provided.

UserÊs Manual 350-1500VA 9

Indicator Table

Status Indicators

The UPS provides both visual and audible status indicators. Visual indicators consist of

three LEDs to represent the following conditions:

 On utility power operation

 On battery power operation

 UPS fault/alarm

LED Indicator Table

On Utility (AC mode) Green Lighting

On Battery (backup mode) Yellow Lighting

Low Battery Yellow Flashing

Fault/Output Short Red Lighting

Overload/Check Battery Red Flashing

LED Audible Alarm Table

On Battery (backup mode) Sounding every 5 seconds

Low Battery Sounding (two beeps) every 5 seconds

Overload Sounding every 0.5 seconds

Replace Battery Sounding (three beeps) every 30 seconds

Fault or output short circuit Continuous sounding

Battery over charge Sounding (three beeps) every 5 seconds

Battery Replacement Procedure:

1. Batteries must be replaced with identical type.

2. Disconnect UPS system from power source

3. Open battery door.

4. Disconnect used battery. Connect new battery. (It is important that connectors be

firmly attached to new batteries.

5. Close battery door.

6. Properly recycle used battery.

UserÊs Manual 350-1500VA

5Ah battery (350VA, 500VA models)

7Ah x 1 battery (700VA models)

Other manuals for Powerware 5110

Table of contents

Other Eaton UPS manuals

Eaton

Eaton 5E700UD-KR Assembly instructions

Eaton

Eaton 5SC 500i User manual

Eaton

Eaton Ellipse PRO 1600 FR User manual

Eaton

Eaton Ellipse ASR 450 User manual

Eaton

Eaton DDC-250/2 Manual

Eaton

Eaton 93E XL User manual

Eaton

Eaton Powerware 9125 User manual

Eaton

Eaton Powerware 5125 User manual

Eaton

Eaton Powerware BladeUPS Quick guide

Eaton

Eaton Powerware 9125 User manual

Eaton

Eaton Powerware 9390 User manual

Eaton

Eaton SU700XLCD User manual

Eaton

Eaton Eaton 5PX User manual

Eaton

Eaton EX RT 5 User manual

Eaton

Eaton 9SX Series User manual

Eaton

Eaton Power Xpert Gateway Minislot Programming manual

Eaton

Eaton BladeUPS Series User manual

Eaton

Eaton Ellipse PRO 650 User manual

Eaton

Eaton Powerware 9355 User manual

Eaton

Eaton Powerware 9390 User manual

Eaton

Eaton Ellipse MAX 600 User manual

Eaton

Eaton Pulsar Series User manual

Eaton

Eaton ON-LINE Series User manual

Eaton

Eaton Eaton 5PX Assembly instructions

Popular UPS manuals by other brands

Pylontech

Pylontech Victron & Pylontech US5000 manual

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 user manual

Mecer

Mecer ME-1000-WTU user manual

Mustek

Mustek PowerMust 530(B) Plus Startup manual

Emerson

Emerson Liebert NXL series Operation and maintenance manual

MAKELSAN

MAKELSAN BOXER SERIES user manual

Block

Block PC-0524-400-0 manual

CyberPower

CyberPower CP585LCD user manual

CyberPower

CyberPower Office Tower Series UPS 1000 user manual

CyberPower

CyberPower BM100 quick start guide

Best Power

Best Power 610 quick start guide

Best Power

Best Power Unity/I UT3K user manual

Mustek

Mustek PowerMust 400 Offline user manual

Xantrex

Xantrex Trace 512 UR-UPS owner's manual

Forza

Forza SL-1501UL user manual

LEGRAND

LEGRAND keor 310081 quick start guide

ABB

ABB Conceptpower DPA 500 operating manual

ZincFive

ZincFive BC Series installation instructions