E-LOK 6 Series User manual
6-Series User Manual
1. Crop out done as per template.
2. Check rubber gasket installed correctly with
lugs pressed in tight. So proper seal around
backplate edge is created.
3. Ensure split pin is installed, securing spindle
to the spindle hub.
4. Ensure screw casing bolts and through bolts tightened.
5. Ensure power cable wire installed correctly and not bent or
crimped in door.
6. Check batteries installed in correct position.
Professionally Installed by:
PIN-Code: Date:
_________________________
____________ ____/____/____
6 - S e r i e s
Summary Check List:
For further details see pages 7-11
Top
Keep the included mechanical keys in a convenient place
such as an Elements Hardware 1236 Key Safe.
Replace the batteries when they have low voltage.
Read this User Manual carefully before installing your 6-
Series Smart Lock.
Use 1.5v Alkaline Batteries.
Please Note:
1236-BLK Shown:
6 - S e r i e s
Contents Page:
Pg 5.
Pg 6.
Pg 7.
Pg 8.
Pg 9.
Pg 10.
Pg 11.
Pg 12.
Pg 13.
Pg 14.
Pg 15.
Pg 16.
Pg 17.
Pg 18.
Pg 19.
Pg 20.
Pg 21.
Pg 22.
Pg 23.
Pg 24.
Pg 25.
Pg 26.
Pg 27.
Pg 28.
Pg 29.
Pg 30.
Pg 31.
Pg 32.
Pg 33.
6-Series Body Dimensions
6-Series Latch
6-Series Packing List
6-Series Specifications
Adjusting the Handing
Installation: Steps 1-5
Installation: Steps 6-7
FactoryReset: If you're admin
Factory Reset: other methods
First Set-Up
Bluetooth Unlock + PIN Code Management
RFID Card Management + Vague Code
RemoteUnlock + e-Key Management
Admin Passcode + Unlock Records
Battery Percentage + Lockset Clock
Passage Mode
Passage Mode + Remote
Extra lock settings 1
Extra lock settings 2
Extra lock settings 3
TransferringOwnership
Unlockwith Mechanical Key
E-LOKGateway Pg. 1
E-LOKGateway Pg. 2
E-LOKGateway Pg. 3
E-LOK Gateway additional notes
Maintenance Guide
Important Notes
Contact
6 - S e r i e s
6-Series Body Dimensions:
5
Top, E-LOK 605 body and lever dimension
Bottom, side view body and lever projection
All measurements in millimeters
6 - S e r i e s
Latch Options:
Back set:
6
6 - S e r i e s
Adjustable backset to 60mm or 70mm to fit the most common size
doors in New Zealand.
Note: Please ensure the slider is at exactly 60mm or 70mm, and not in
between.
Allen Wrench
QTY 1
6-Series Packing List:
Front Panel
QTY 1
Back Panel
QTY 1
User Manual
QTY 1
Mechanical Key
QTY 2
RFID Card
QTY 3
Screw A
QTY 4
Gasket
QTY 2
Screw C
QTY 2
Screw Casing
QTY 3
Column
QTY 2
7
Spindle
QTY 1
6 - S e r i e s
Screw B
QTY 4
Specifications:
E-LOK 6-Series Smart Lock
E-LOK App
Black or Silver
PIN Code
RFID Card
E-LOK App
Mechanical Key
Unlimited
150 PIN Codes
200 RFID Cards
6V (4 x 1.5v AA Batteries)
— 10°C - 55°C
0% - 95%
35mm - 65mm
Aluminium Door, Wooden Door
140mm(H) x72mm(W) x19mm(D)
124mm(L)
60mm and 70mm Back Set
2 Year Mechanical and Electrical
2 Year
Exterior Rated IP 55
Product Name:
Operating Application:
Finish:
Unlock Methods:
Max Num. Locks on App:
Max Num. PIN Codes:
Max Num. RFID Cards:
Batteries:
Operating Temp:
Operating Humidity:
Suitable Door Thickness:
Suitable Door Types:
Product Size (Body only):
Product Size (Lever):
Available Latch Sizes:
6-Series Residential Warranty:
E-LOK Gateway Warranty:
Weather Rating:
8
- Must be Alkaline
6 - S e r i e s
Steps to change the handing on E-LOK 6-Series:
9
Adjusting The Handing:
6 - S e r i e s
Note: Adjust the handle according to the direction you open the door.
For Exterior Assembly:
Loosen the screw
with the 3mm
Allen Wrench
1. 3. Tighten the screw
after adjusting the
handle direction.
2. Adjust the door
handle direction
For Interior Assembly:
Loosen the screw1. 3. Tighten the screw
after adjusting the
handle direction.
2. Lift off door handle,
and adjust the door
handle direction
Step 1.
If you are retrofitting into anexisting 54mm
hole, this step may not be required. If you
are fitting the 6-Series into a new hole,
begin to cut the precise holes into your
door. Your E-LOK 6-Series comes with
screws to suit both wooden and aluminum
doors. Insert latch and screw in.
Step 2.
Install the Gasket (Waterproof rubber plate)
to the exterior panel.
Step 3.
Install spindle into spindle hub. Also install
the split pin, to hold spindle to spindle
hub. (See step 3 for image)
Step 4.
Install 2 positioning columns.
Installation:
10
6 - S e r i e s
Step 5.
Install the 3 screw casings and place
exterior panel on the door.
This manual suits for next models
1
Table of contents
Other E-LOK Door Lock manuals
