DW DWC-D3763WTIR User manual
05/2015
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Analog High Definition
Indoor Dome Camera
DWC-D3763WTIR
2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Easy Installation
Connecting to Monitors 9
Control Board
4
5
6
7
8
10
11
12-25
26
27-28
29-30
Adjusting the Camera Angle
4
FEATURES*
Analog High Definition (AHD) HD over Coax Technology
STAR-LIGHT™ Super Low Light Technology
Panasonic 1/3" CMOS Sensor
1080P Resolution at 30fps
Digital Wide Dynamic Range (DWDR)
Varifocal P-Iris Lens 2.8~12mm
Smart IR™ with Intelligent Camera Sync. 100ft Range
Smart DNR™ 3D Digital Noise Reduction
Highlight Masking Exposure (HME)
True Day/Night Mechanical IR Cut Filter
Secondary Video-BNC Output (While UTP in use)
Easy Icon Driven OSD Menu with Built-in Joystick
Programmable Privacy Zones
Auto Gain Control (AGC)
Back Light Compensation (BLC)
Dynamic Range Compressor (DRC) Reveals Low Light Detail
Auto White Balance (AWB)
Set Screw
5
PARTS & DESCRIPTION*
1Bottom Case
UTP Cables
RS485 Cables
Alarm Output Cable
Camera Gimbal
Upper Case
Dome Cover
5
6
7
2
3
4
1
2
3
4
5
6 7
6
DIMENSIONS IN MILLIMETERS (IN)*
120.0 4.72”
9.0 0.3539.0 1.53”
89.4 3.52”
81.0 3.19”
89.0 3.50”
7
INSIDE THE BOX*
Included with your Camera:
1
2
5
4
3
User Manual
Mounting Template
2 Machine Screws and 2 Dry Wall Anchors
Secondary Video-BNC Cable
Power Cable
10222013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Strlight MPA
Indoor Dome Camera
DWC-D3661T
DWC-D3661TIR
8
EASY INSTALLATION*
1. To detach the camera’s cover dome from the camera’s module
press the small buttons located at the sides of the cover dome.
While pressing the buttons, disconnect the cover dome from the
camera’s base module.
2. Use the camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.
3. Pull wires through and make connections.
4. Using the two (2) included screws, mount and secure the
camera to the wall or ceiling.
5. Adjust the camera’s Pan and Tilt. See page 12 for more
information.
6. Use the joystick to adjust the OSD menu. See pages
13-21 for more information.
7. Snap the camera’s cover dome to the camera base to complete
the installation.
9
Use the diagram below to connect to a Monitor or CRT Monitor properly.
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
CONNECTING TO MONITORS*
12VDC/24VAC
Monitor
CCTV Monitor
Second Video Output Right
Left
Up
Down
10
Joystick: Controls
the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
CONTROL BOARD*
Remove the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.
1
2
Other DW Security Camera manuals
DW
DW DWC-MV95WiATW User manual
DW
DW DWC-V6563D User manual
DW
DW Star-Light Plus DWC-D4883WTIRW Instruction Manual
DW
DW DWC-HF21M4TIR User manual
DW
DW DWC-C261T User manual
DW
DW DWC-MT95WiATW User manual
DW
DW DWC-MD44WA User manual
DW
DW DWC-MB74Wi4 User manual
DW
DW MEGAPIX DWC-MC421D User manual
DW
DW MEGApix DWC-MV95Wi28TW User manual
DW
DW MEGApix DWC-VSBD04Bi User manual
DW
DW Star-Light Plus DWC-PTZ220XW User manual
DW
DW DWC-PTZ20X User manual
DW
DW DWC-MB72I4V User manual
DW
DW DWC-D1362D User manual
DW
DW DWC-MT95Wi28TW User manual
DW
DW DWC-MPTZ30X User manual
DW
DW DWC-MVC8WiATW User manual
DW
DW DWC-VSDG04Bi User manual
DW
DW DWC-LPR650 User manual
