DSC PC2550 User manual

Code Changes

User’s Programming Commands

[*]+[5]+[MASTER CODE]

The [*][5] user’s programming commands are used to program additional access codes. Up to 16 user arm-

disarm codes may be programmed. The 1st code is the Master Code (factory default [1234]). The 16th code

is optionally a “One Time Use”or maid code. The 16th code may be changed from a “One Time Use” code to

a regular code using an installer’s programming command (section [15]...light 8). Remember if no keypad

entry is made for more than 2 minutes the keypad will return to the normal arm-disarm display and the

complete command will have to be re-entered to program a new access code.

Programming Additional Access Codes

1. Press the [*] and [5] keys then enter the Master Security Code (default [1234]) to enter the additional code

programming mode. The “Program” light and “Zone 1” light will be on to show that the rst code (the Master

Code) is already programmed with the factory default code [1234]. The Master Code may be changed but do

not try to erase the Master Code. The installer can disable user changing of the Master Code by turning on

light 2 in section [16].

2. 15 additional codes may be programmed. The zone lights are used to indicate which of these codes are

already programmed (zone light on steady) and the one which is currently being programmed (zone light is

ashing).

3. To program the second code, press [2] and zone 2 light will ash. Then enter a 4 digit code and the buzzer

will beep three times and zone light 2 will come on steady indicating a programmed code.

4. To remove the second code, press [2] - the buzzer will beep three times and zone light 2 will ash. Enter

[*] [*] [*] [*], the buzzer will beep three times and zone 2 light will go out to show that the code has been

removed.

5. Follow the instructions in 3 or 4 for programming or removing any of the other additional codes.

6. To program access codes 9 to 16, press 9 to toggle into the upper code region. Zone lights 1 to 8 now rep-

resent access codes 9 to 16 (light 1 is code 9.... light 8 is code 16). The “Ready” and “Armed” LEDs will ash to

indicate that the user is in the upper programming region. Program or remove access codes 9 to 16 as stated

in 3 and 4 above. Press 9 again to toggle back down to the lower region (access codes 1 to 8).

7. Do not try to remove the Master Code (1st code). The Master Code may be changed but it must not be

removed. When changing the Master Code be sure to enter a valid 4 digit number (use only number keys 0

to 9). Do not enter [#] or [*] as one of the digits. If the Master Code is forgotten and the panel is left disarmed,

program a new Master Code using the [*][8][Installer’s Code][25] command. If the Master Code is forgotten

and the panel is left armed, use the 2nd Master Code to disarm the system. If the 2nd Master Code is not

programmed then the entire programming can be reset to factory default by using the “Hardware Reset”

method described on page 24.

8. To successfully program or remove additional codes, the panel must be put into the code program mode

by following step 1 followed by steps 3 or 4. Note that if no key entry is made for 2 minutes the panel will go

back to the normal arm/disarm mode, after which step 1 must be repeated to get back into the code pro-

gram mode.

9. To exit the code program mode press [#].

To review:

programming a new code;

enter [*] [5] [Master Code] [1 to 8] [4 digit code], or

[*] [5] [Master Code] [9] [1 to 8] [4 digit code]

eliminating an existing code;

enter [*] [5] [Master Code] [2 to 8] [* * * *], or

[*] [5] [Master Code] [9] [1 to 8] [* * * *].

Note: The access code numbers must be entered as

one digit. E.g. 2, 3,......, 7, 8.

Other manuals for PC2550

Table of contents

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual