Dover MagLink LX4 User manual

ProGauge MagLink LX 4 Installation Manual

Part Number: M2050

Revision: 4

MagLink LX 4

Table of Contents

Section 1 Preface 4

Section 2 General Warnings 5

Section 3 Introduction 6

3.1 Safety Warnings 8

3.2 Information Panels 8

Section 4 General Indications 10

Section 5 Product Labels 12

Section 6 Installation 14

6.1 Installation Warnings 14

6.2 Installation Location 14

6.3 Electrical Connection 15

6.4 Installation Procedure 16

Section 7 Connections 18

7.1 Connection to the Intrinsically Safe XMT-SI and DMP-SI Probes 19

7.2 Connection to the XMT Explosion-proof Probe 20

7.3 Connection to the RF Receiver (for XMT-SI-RF) 21

7.4 Interface to Relay - Diagram of Connectors 22

7.5 DIP-Switch Configuration 24

7.6 Micro SD Card 25

7.7 Close and Start Up the Console 26

7.8 DB9 Connections to a Management System 26

7.8.1 FuelPOS/DIALOG Fuel Management System 26

7.8.2 GILBARCO Fuel Management System 27

7.8.3 Wayne Fusion Fuel Management System 27

Section 8 Maintenance 29

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 2

Section 9 Technical Support 30

Section 10 Wiring Diagrams 31

10.1 Connect XMT-SI probes 31

10.2 Connect XMT Exd probes 32

10.3 Connect RF Probes 33

10.4 Connect On/Off Sensors 34

Appendix A - Console Dimensions 35

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 3

Section 1 Preface

Start Italiana S.r.l. has made every effort possible to see that this document is complete, accurate and

updated. With every revision of the console, the related information is added to the document. Start Italiana

S.r.l. reserves the right to make unannounced improvements and/or changes in the product and/or

associated programs. Start Italiana S.r.l. is not liable for damages of any kind, including those resulting in the

document, including typographical errors.

Making copies, citing quotes or other reproductions of all or part of this document is permitted only after

written consent of Start Italiana S.r.l.

Patents protect trademark or name.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 4

Section 2 General Warnings

Carefully read the instructions in this manual before you do the installation procedures.

Only approved persons are permitted to install this equipment and configure the console.

The manufacturer is not responsible for operations that are not included in this manual.

The manufacturer is not liable in regards to competent bodies for changes to the equipment and software

that are not approved.

In case of failure or defect, refer directly to an authorized service provider or manufacturer.

The manufacturer is not liable for injury and/or damage to persons and/or property and/or pets caused by the

failure to obey safety instructions.

All approved personnel must know all safety requirements in this manual, the configuration manual and the

user manual.

Refer directly to an approved service provider or manufacturer for questions about the operation of the

equipment.

IMPORTANT: You must read and obey all safety instructions in this manual before you use

this equipment.

WARNING: Incorrect use of this equipment that does not agree with the

instructions in this manual can cause a risk to safety.

IMPORTANT: If a replacement power supply cable is necessary, use an applicable, approved

ELBZ/7 type power cord. Do not use another type of power cable.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 5

Section 3 Introduction

This manual was prepared in accordance with IEC 82079-1 standards. “Preparation of instructions for use -

Structuring, content and presentation - Part 1: General principles and detailed requirements and according to

the ATEX Directive 2014/34/EU concerning equipment and protective systems intended for use in potentially

explosive atmospheres."

This manual gives all necessary information about the installation of the MagLink LX 4 console.

IMPORTANT: This manual must be used together with the related product manuals:

M2051 MagLink LX 4/LX Plus Configuration Manual

M2052 MagLink LX 4/LX Plus User Manual

You must install the console as shown in this manual, configure the console as instructed in

the M2051 MagLink LX 4/LX Plus Configuration Manual, and use the console in the field as

shown in the M2052 MagLink LX 4/LX Plus User Manual.

WARNING: This device must not be discarded with household waste. This

device is labeled in accordance with European Directive 2012/19/UE

concerning used electrical and electronic appliances (waste electrical and

electronic equipment – WEEE).

This guideline gives the methods for the return and recycling of used

electronic devices as applicable throughout the EU. To return your used

device, use the return and collection systems available to you.

The battery used in this device may present a risk of fire or chemical burn if

mistreated. Do not disassemble, heat above 50°C or incinerate.

The table that follows lists reference data of the manufacturer:

Data Description

Name START ITALIANA S.r.l.

Address

Via Natta 6

20823 Lentate Sul Seveso, (MB)

Italy

Telephone +39 0362 1581465

Fax +39 0362 1581464

Website www.startitaliana.com

e-Mail [email protected]

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 6

INFORMATION: The units of measurement contained in this manual refer to a specified

selection by the user. Refer to the M2051 MagLink LX 4/LX Plus Configuration Manual for

more information on how to set units of measure.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 7

3.1 Safety Warnings

This manual contains many important Safety Alerts. There can be a risk of injury or damage to property if you

do not obey these alerts. The panels below show the types of safety warnings that can be seen and how

each is specified.

DANGER: Indicates an immediately hazardous condition that, if not prevented, will

result in death or serious injury.

WARNING: Indicates a possibly hazardous condition that, if not prevented, could

result in death or serious injury.

CAUTION: Indicates a possibly hazardous situation that, if not prevented, could

result in minor or moderate injury.

NOTICE: Indicates important information not related to hazards. A condition that, if not

prevented, can result in property damage.

SAFETY INSTRUCTIONS: Indicates instructions and procedures related to safety or

gives the location of safety equipment

3.2 Information Panels

NOTE: This panel gives more information about an instruction or procedure.

IMPORTANT: This panel contains special information that is important and must be read and

obeyed.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 8

REMINDER: This panel shows information that has been given before in the manual that is

important to show again.

TIP: A step or procedure that is recommended to make another step or procedure easier.

INFORMATION: This panel shows references to more information in other sources.

READ CAREFULLY: This panel points to information that must be fully read and understood

before doing the procedure(s) that comes after.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 9

Section 4 General Indications

The MagLink LX 4 console is shipped in a cardboard box (L 450 x H 300 x D 200 [mm]) and includes the

components as follows:

lMagLink LX 4 console

lConnection cable (220 V AC with Schuko plug)

lQuality control certification checklist

lUser manual, installation manual and web configuration manual

Weight of the console with its carton: 2 kg.

The table below shows the primary technical characteristics of the console:

Element Characteristic

Display Display TFT 7inch

Dimensions 155 x 88 [mm]

Console

Dimensions

· Width 267 mm

· Height with cable: 215 mm

· Depth 80 mm

The illustration below shows the ports and connections on the bottom of the console:

Make sure that the power cable is correctly installed. Put the Power Switch to the on ("I") position to supply

power to the console.

Put the Power Switch in the off ("O") position to remove power from the console.

M2050 MagLink LX 4 Installation Manual | Dover Fueling Solutions 10

Other manuals for MagLink LX4

This manual suits for next models

Table of contents

Other Dover Controllers manuals

Dover

Dover HYDRO Multi-Washer 3000 Series User manual

Dover

Dover Hydro Connected Total Eclipse User manual

Dover

Dover Markem-Imaje LASER 7031 Quick start guide

Dover

Dover DESTACO Automating Tomorrow ROBOHAND DRF... User manual

Dover

Dover MagLink LX4 User manual

Dover

Dover DESTACO ROBOHAND DRG Series User manual

Dover

Dover All-Flo PSG 72000-00 Owner's manual

Dover

Dover Petro Vend FSC3000 User manual

Dover

Dover All-Flo PSG 72100-00 Owner's manual

Dover

Dover NEPTUNE PSG NEP-131906 Owner's manual

Dover

Dover DMM-0200 Specification sheet

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual