Dorma ED900 User manual

ED900 POWER CORD INSTALLATION

—

DORMA AMERICAS, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: [email protected]

08122560 08/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

Installing the power cord

1.1 Disassemble the conduit box assembly, by removing

the pan head screw from the terminal block using a #1

phillips screw driver.

1.2 Slide the conduit box underneath the mounting plate.

1.3 Insert the pan head screw into the terminal block,

bushing and conduit box by using a #1 phillips screw

driver (5in-lbs).

Conduit box

Screw

Terminal block

1. 110V power cord

2. Conduit box

3. Cord grip

4. Wire nut

Bushing

Mounting

plate

The flexible power cord should not be routed through doorways, window openings, walls, ceilings, floors, or the like. The

cord should also not be attached or secured to the building structure. The cord cannot be concealed behind walls and the

like. Make sure the power cord does not become entrapped in any moving parts of the operator, door, or system.

To reduce the risk of electric shock, this equipment has a grounding type plug, that has a third (grounding) pin. This plug

will only fit into a grounding type outlet. IF the plug does not fit into the outlet, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

For in-wall mounting: When installing the socket, please remember that the socket should be reached by hand.

(maximum 14" away)

ATTENTION! Connect the power cord to 120V 60 Hz ONLY.

WARNING! Power cords pose a rise of becoming entrapping in moving parts of the operator, door or system.

ED900 POWER CORD INSTALLATION

DORMA AMERICAS, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: dormaarchitectural@dorma. com

08122560 08/14 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

2.1 Punch out the hole in the conduit box best suited for the

application.

2.2 Place the power cord into the grommet portion of the

cord grip and insert the cord grip into the hole using

pliers to compress it.

Hole

Conduit box

Cord

grip

Wiring the ED900

1.1 Loosen the terminal block connections and secure each

wire of the 110V power cable into its proper location on

the terminal block.

Black (live) = upper terminal

White (neutral) = lower terminal

Green (ground) = connect to ground wire

1.2 Align the mounting plate/conduit box assembly with the

bottom of the ED900 unit.

1.3 Feed the terminal block power cable through the bottom

of the plastic housing. CAUTION: DO NOT DAMAGE THE

WIRES.

2.1 Insert the male connection end of the main power cable

into the female connector inside the housing.

Terminal block Power cable

ED900 unit

Mounting plate/conduit box

Terminal

block power

cable

Housing

Male

connection

end

Female

connection

end

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual