Dimplex DS7420 User manual

Owner’s Manual

Model

DS7420

DS7425DLX

7206380100rev07

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this stove. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Welcome & Congratulations ........................3

Important Instructions .............................4

Quick Reference Guide ............................6

Stove Installation .................................6

Operation .......................................7

Maintenance ....................................9

Warranty ......................................12

Table of Contents

Always use a qualied technician

or service agency to repair

this stove.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations

Thank you and congratulations for

choosing to purchase an electric

stove from Dimplex, the world

leader in electric replaces.

Please carefully read and save

these instructions.

CAUTION: Read all

instructions and warnings

carefully before starting

installation. Failure to follow

these instructions may result

in a possible electric shock,

re hazard and will void

the warranty.

Please record your model and

serial numbers below for future

reference: model and serial

numbers can be found on the

Model and Serial Number Labels

of your stove.

NO NEED TO RETURN

TO THE STORE

Questions With the Assembly?

Require Parts Information?

Product Under Manufacturer’s

Warranty?

Call Toll-Free

1-888-346-7539

Monday to Friday

8:00 a.m. to 4:30 p.m. EST

Please have your model

number and product serial

number ready. (See below)

Model Number

Serial Number

4 www.dimplex.com

When using electrical appliances,

basic precautions should always be

followed to reduce the risk of re,

electric shock, and injury to persons,

including the following:

①Read all instructions before using

the stove.

②The heater is hot when in use.

To avoid burns, do not let bare skin

touch hot surfaces. The trim around

the heater outlet becomes hot during

heater operation. Keep combustible

materials, such as furniture, pillows,

bedding, papers, clothes, and

curtains at least 3 feet (0.9m) from

the front of the unit.

CAUTION: High Temperature, keep

electrical cords, drapery, and other

furnishings at least 3 feet (0.9m)

from the front of the heater and

away from the side and rear.

③Extreme caution is necessary

when any heater is used by or near

children or invalids and whenever the

unit is left operating and unattended.

④Always unplug the stove when

not in use.

⑤Do not operate any unit with a

damaged cord or plug, or if the heater

has malfunctioned, or if the stove has

been dropped or damaged in any

manner. Return heater to authorized

service facility for examination,

IMPORTANT INSTRUCTIONS

electrical or mechanical adjustment,

or repair.

⑥Do not use outdoors.

⑦The stove is not intended for

use in bathrooms, laundry areas and

similar indoor locations. Never locate

heater where it may fall into a bathtub

or other water container.

⑧Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from trafc area

and where it will not be tripped over.

⑨To disconnect the unit, turn the

controls off, then remove the plug

from the outlet.

⑩Do not insert or allow foreign

objects to enter any ventilation or

exhaust opening as this may cause

an electric shock or re, or damage to

the heater.

⑪To prevent a possible re, do

not block air intake or exhaust in any

manner. Do not use on soft surfaces,

like a bed, where openings may

become blocked.

⑫All electrical heaters have hot

and arcing or sparking parts inside.

Do not use in areas where gasoline,

paint, or ammable liquids are used

or stored or where the unit will be

exposed to ammable vapors.

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

⑬Do not modify the stove. Use

it only as described in this manual.

Any other use not recommended by

the manufacturer may cause re,

electric shock or injury to persons.

⑭To reduce the risk of electric

shock, this appliance has a polarized

plug (one blade is wider than the

other). This plug will t in a polarized

outlet only one way. If the plug does

not t fully in the outlet, reverse the

plug. If it still does not t, contact

a qualied electrician to install the

proper outlet. Do not change the

plug in any way. Avoid the use of an

extension cord. Extension cords may

overheat and cause a risk of re. If

you must use an extension cord, the

cord must be No. 14 AWG minimum

size and rated no less than

1875 Watts.

⑮Do not burn wood or other

materials in the stove.

⑯Do not strike the clear door

panel.

⑰ Always use a certied electrician

should new circuits or outlets be

required.

⑱Always use properly grounded,

fused and polarized outlets.

⑲Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the unit.

⑳When transporting or storing the

unit and cord, keep in a dry place,

free from excessive vibration and

store so as to avoid damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

6 www.dimplex.com

Quick Reference Guide

① Prior to the rst use of the

stove verify the following:

• Are the circuit breakers for the

unit on?

• Are the light bulbs in your

stove loose? (To check, follow

the instructions for replacing

the light bulbs under the

Maintenance section of this

manual.)

②The heater on your stove may

emit a slight, harmless odor when

rst used. This odor is a normal

condition caused by the initial

heating of internal heater parts

and will not occur again.

Stove Installation

!NOTE: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not

essential in all cases. A

dedicated circuit will be

required if, after installation,

the circuit breaker trips or

fuses blow on a regular basis

when the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that

it is pinched or against a

sharp edge and ensure that

the power cord is stored or

secured to avoid tripping or

snagging to reduce the risk of

re, electric shock or injury to

persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

always use a licensed

electrician.

Stove Installation

Installation

①Make sure the unit’s Main On/

Off Switch is switched Off (refer to

operating instruction section).

Operation

To access the controls, go to the

back of the stove (Figure 1).

control. When in “II” position

the unit is operated with the ON

and OFF buttons of the remote

control.

When the switch is in the center

position “O” the unit is off.

B. Light On/Off Switch

The Light On/Off Switch supplies

power to the upper light of the log

bed display area.

C. Heater On/Off Switch

The Heater On/Off Switch

supplies power to the heater.

D. Heater Thermostat Control

To adjust the temperature to

your individual requirements,

turn the thermostat control

clockwise all the way to turn

on the heater. When the room

reaches the desired temperature,

Figure 1

A B C

A. Three Position On/Off

Switch

The switch has two On positions

marked with “I” and “II”. The “I”

position is for manual operation.

In this position the built-in remote

control is bypassed.

The “II” position is for operating

the unit with the provided remote

②Plug the unit into a 15 Amp/

120 VAC outlet. If the cord

does not reach, you may use

an extension cord rated for a

minimum of 1875 Watts.

8 www.dimplex.com

Operation

turn the thermostat knob counter

clockwise until you hear a click.

Leave in this position to maintain

the room temperature at this

setting. For additional heat, turn

clockwise until you hear the click

again and the heater will turn on.

Resetting the Temperature

Cutoff Switch

Should the heater overheat, an

automatic cut out will turn the

heater off and it will not come

back on without being reset. It

can be reset by switching the

Three Position Switch to Off

“O” and waiting ve (5) minutes

before switching the unit back on.

CAUTION: If you need to

continuously reset the heater,

unplug the unit and call

Customer Service at

1-888-346-7539.

Remote Control

The stove is supplied with an

integrated On/Off remote control.

!NOTE: Ensure that the

stove's Three Position Switch

is set to the remote Control

setting (“II” position).

To operate, push the ON button

to turn stove on, push the OFF

button to turn the stove off.

Battery Installation

To install or replace the battery:

• Slide battery cover open on the

hand held transmitter (Figure 2).

• Correctly install one (1) 12 Volt

(A23) battery in the battery

holder.

• Close the battery cover.

Figure 2

On Button

Off Button

Battery

Cover

Remote Initialization

Follow these steps for remote

control initialization and if

required, re-initialization:

①Disconnect power to stove.

②Set the Three Position On/Off

Switch to the Remote position

(Figure 1A).

Operation

③ Wait a minimum of ve (5)

seconds and then re-acquire

power to stove.

④Within 10 seconds of re-

acquiring power, press the ON

button located on the remote

control transmitter.

!NOTE: You will have only 10

seconds to perform this last

step. Failure to do so will result

in these steps needing to be

followed again.

 WARNING: Disconnect

power before attempting any

maintenance or cleaning to

reduce the risk of re, electric

shock or damage to persons.

Light Bulb Replacement

Allow at least ve (5) minutes

for light bulbs to cool off before

touching bulbs to avoid accidental

burning of skin.

Light bulbs need to be replaced

when you notice a dark section

of the ame or when the clarity

and detail of the log exterior

disappears.

There are three (3) bulbs under

the Log Set Assembly, which

generate the ames and embers,

Maintenance

and one (1) bulb above that

illuminate the log exterior.

Tool Requirements:

Phillips screw driver

Helpful Hints

It is a good idea to replace all

light bulbs at one time if they are

close to the end of their rated life.

Group replacement will reduce

the number of times you need

to open the unit to replace light

bulbs.

Upper Bulb Requirement

Quantity of one (1) 7 Watt

candelabra E12 small base

120 Volt.

Do not exceed 7 Watts per bulb.

10 www.dimplex.com

Upper Bulb Replacement

(Figure 3)

Maintenance

Lower Bulb Replacement

①Remove the stove pipe kit (if

equipped).

②Gently place stove on its back

on a at surface.

③Remove the heater cover

retaining screws located on the

bottom of the stove (Figure 4) and

lower heater and light assembly

out onto the oor.

Figure 3

①Open door by pulling the

handle.

②Locate the upper bulb bracket.

③Bend light retainer bracket

down.

④Locate and remove light bulb.

⑤Insert and install new bulb.

⑥Bend light retainer bracket

back into its original position.

⑦Close the door.

Lower Bulbs Requirement

Quantity of three (3) 35 Watt

Halogen Quartz lamps, 120 Volt,

G9 Base.

Do not exceed 35 Watts per

bulb.

Figure 4 Screws

Screws

④Remove the burnt out bulb(s)

by pulling straight out of socket. If

bulbs are difcult to remove form

socket move the bulb from side

to side while pulling being careful

not to damage the light socket.

⑤Replace the lower light bulbs.

⑥Reassemble in the reverse

order as above.

Other manuals for DS7420

This manual suits for next models

Table of contents

Other Dimplex Indoor Fireplace manuals

Dimplex

Dimplex EWMC-CC-SS User manual

Dimplex

Dimplex Opti-Suite2Go2 User manual

Dimplex

Dimplex SP29 User manual

Dimplex

Dimplex 6905050100-500 User manual

Dimplex

Dimplex CAS500R User manual

Dimplex

Dimplex TOLUCA TLC20 Instruction Manual

Dimplex

Dimplex DF2305 User manual

Dimplex

Dimplex BAR20-AU User manual

Dimplex

Dimplex SP820 User manual

Dimplex

Dimplex TFA36E User manual

Dimplex

Dimplex Vivente Plus V V T75 Manual

Dimplex

Dimplex DF3003 User manual

Dimplex

Dimplex Silverton SVT20 User manual

Dimplex

Dimplex THWG XLF74 User manual

Dimplex

Dimplex Prism 50 User manual

Dimplex

Dimplex BIZET BZT20 User manual

Dimplex

Dimplex Opti-Myst Cassette 500 User manual

Dimplex

Dimplex DF1135M User manual

Dimplex

Dimplex DF2426GB User manual

Dimplex

Dimplex DWF36-PG User manual

Dimplex

Dimplex MULTIFIRE DF3015 User manual

Dimplex

Dimplex DF2010-EU-E User manual

Dimplex

Dimplex BF33ST User manual

Dimplex

Dimplex Marbello User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual