Dimplex DFI2310 User manual
Owner’s Manual
Model
DFI2309
DFI2310
7205650300R04
IMPORTANT SAFETY INFORMATION: Always read this manual rst
before attempting to install or use this replace. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
2 www.dimplex.com
Table of Contents
Always use a qualied technician
or service agency to repair
this replace.
!NOTE: Procedures and
techniques that are considered
important enough to
emphasize.
CAUTION: Procedures
and techniques which, if not
carefully followed, will result in
damage to the equipment.
WARNING: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of re,
serious injury, or death.
Welcome & Congratulations .................3
IMPORTANT INSTRUCTIONS ...............4
Fireplace Installation .......................7
Operation ................................9
Maintenance ............................11
Warranty ...............................13
Technical Support .........................16
3
Welcome & Congratulations
Model Number
Serial Number
Thank you and congratulations for purchasing an electric replace from
Dimplex. Please use our convenient online registration page to record
your model and serial numbers for future reference at
www.dimplex.com/register
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at: www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
In order to better serve you, please have your model and serial number
ready or register your product online before calling (See above)
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in
a possible electric shock, re hazard and will void the warranty.
4 www.dimplex.com
IMPORTANT INSTRUCTIONS
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
① Read all instructions before
using this heater.
② This heater is hot when in use.
To avoid burns, do not let bare
skin touch hot surfaces. The trim
around the heater outlet becomes
hot during heater operation.
Keep combustible materials, such
as furniture, pillows, bedding,
papers, clothes, and curtains at
least 3 feet (0.9 m) from the front
of the heater and keep them away
from the sides and rear.
③ Extreme caution is neces-
sary when any heater is used by
or near children or invalids and
whenever the unit is left operating
and unattended.
④ Always unplug the heater when
not in use.
⑤Do not operate any heater
after it malfunctions. Disconnect
power at the service panel and
have the heater inspected by a
reputable electrician before reus-
ing.
⑥ Do not operate any unit with
a damaged cord or plug, or if the
heater has malfunctioned, or if
the electric replace has been
dropped or damaged in any man-
ner, contact Dimplex Technical
Service at 1-888-346-7539.
⑦ Do not use outdoors.
⑧ This heater is not intended for
use in bathrooms, laundry ar-
eas and similar indoor locations.
Never locate this heater where
it may fall into a bathtub or other
water container.
⑨ Do not run cord under carpet-
ing. Do not cover cord with throw
rugs, runners, or the like. Arrange
cord away from trafc area and
where it will not be tripped over.
⑩ To disconnect heater, turn
controls to off, then remove plug
from outlet.
⑪ Do not insert or allow foreign
objects to enter any ventilation
or exhaust opening as this may
cause an electric shock or re, or
damage the heater.
⑫ To prevent a possible re, do
not block air intakes or exhaust in
any manner.
⑬ All electrical heaters have
hot and arcing or sparking parts
5
SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
inside. Do not use in areas where
gasoline, paint, or ammable
liquids are used or stored.
⑭ Do not modify the heater. Use
it only as described in this man-
ual. Any other use not recom-
mended by the manufacturer may
cause re, electric shock, or injury
to persons.
⑮This unit may have a polarized
plug (one blade is wider than the
other). The plug will t in a polar-
ized outlet only one way. If the
plug does not t fully in the outlet,
reverse the plug. If it still does not
t, contact a qualied electrician
to install the proper outlet.
⑯ Always plug heaters directly
into a wall outlet/receptacle.
Never use with an extension cord
or relocatable power tap (outlet/
power strip).
⑰ Do not burn wood or other
materials in the Fireplace.
⑱ Do not strike the front glass.
⑲ Always use a certied electri-
cian should new circuits or outlets
be required.
⑳ Always use properly grounded,
fused and polarized outlets.
㉑ Do not install the replace
directly on carpet or a similar
surface, which may restrict air
circulation beneath the unit.
㉒ Disconnect all power supply
before performing any cleaning,
maintenance or relocation of the
heater.
㉓ When transporting or storing
the heater and cord, keep in a
dry place, free from excessive
vibration and store so as to avoid
damage.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
6 www.dimplex.com
IMPORTANT INSTRUCTIONS
This equipment has been tested and
found to comply with the limits for Class
B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and the receiver.
• Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Operation is subject to the following
two conditions: (1) this device may not
cause interference and; (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
WARNING: Remote control
contains small batteries
keep away from children. If
swallowed seek medical
attention immediately.
WARNING: Do not install
battery backwards, charge, put
in re or mix with used or other
battery types - may explode or
lead causing injury.
!NOTE: Changes or
modications not expressly
approved by the party responsible
for compliance could void
user's authority to operate the
equipment.
7
Fireplace Installation
WARNING: Ensure the power
cord is not installed so that it is
pinched or against a sharp edge
and ensure that the power cord is
stored or secured to avoid tripping
or snagging to reduce the risk
of re, electric shock or injury to
persons.
WARNING: Construction
and electrical outlet wiring must
comply with local building codes
and other applicable regulations
to reduce the risk of re, electric
shock and injury to persons.
WARNING: Do not attempt
to wire your own new outlets or
circuits. To reduce the risk of re,
electric shock or injury to persons,
always use a licensed electrician.
WARNING: To reduce the risk
of re, do not store or use gaso-
line or other ammable vapors or
liquids in the vicinity of the heater.
CAUTION: High temperature,
risk of re, keep electrical cords,
drapery, furnishings, and other
combustibles at least 3 ft (0.9 m)
from the front of the heater.
!NOTE: A 15amp, 120-volt cir-
cuit is required. A dedicated cir-
cuit is preferred but not essential
in all cases. A dedicated circuit
will be required if, after installa-
tion, the circuit breaker trips or
the fuse blows on a regular basis
when the heater is operating. Ad-
ditional appliances on the same
circuit may exceed the current
rating of the circuit breaker.
CAUTION: Clearance for air
circulation beneath the replace
insert is provided by two rubber
feet. Do not install the replace
insert directly on carpet or
similar surfaces which may
restrict air circulation.
CAUTION: If installing the
replace in a carpeted area, place
a one-piece, solid, at surface
under the replace. Ensure that
both of the feet rest securely on
this surface.
!NOTE: The electric insert
must be installed in an opening
with the minimum dimensions
24 in. (61 cm) wide, 21.5 in. (54.6
cm) high and 12 in. (30.5 cm)
deep. The replace does not
require any additional venting
(Figure 1).
Existing Fireplace
1. Seal all drafts and vents with a
non-brous insulation material
to prevent any chimney debris
from falling onto the replace.
Do not install into an existing
8 www.dimplex.com
Fireplace Installation
replace that is prone to damp-
ness.
2. Cap the top of the chimney ue
to prevent rain from entering.
3. Plan your electric power sup-
ply.
4. Install an outlet into the exist-
ing replace. If an outlet is not
installed into the existing re-
place the power cord can also
run along the front of the hearth
to an outlet near the replace.
5. Ensure the insert power is off
(see Operation). Plug the insert
into the outlet and slide the unit
into the existing replace.
6. Push the insert into the rebox
and center within the open-
ing. Adjust the four feet on the
bottom of the insert by turning
counter clockwise to raise and
clockwise to lower so that is
level with the existing replace
hearth.
7. Install the trim kit onto the re-
place insert (if applicable) and
push the trim and or insert back
until the trim is at against the
nished wall.
WARNING: The replace
insert can be used with
existing replace and screens.
Due to the heat produced
from the heater, existing
replace screens must
provide adequate air ow in
front of the unit. Do not use
existing replace doors
that close, sealing off the
replace insert from the
room. If installed behind
bi-fold doors, doors must
be open to allow heat to be
exhausted.
WIRING
CONTROL RECEIVER
REMOTE
FLICKER
MOTOR
SWITCH
3-POSITION
SWITCH
LOW HEAT SWITCH
HIGH HEAT
MOTOR
THERMAL
CUTOUT
ELEMENT
L
N
MLED
LOGS
LED
DRIVER
BOARD
DFI2310 ONLY
LOWER
LIGHTS
9
WARNING: This electric
rebox must be properly installed
before it is used.
Manual Controls
A - 3-Position Switch
The switch has two On positions
marked with “ I” and “ II ”. The “ I
” position is for manual operation.
In this position the built-in remote
control is bypassed.
The “ II ” position is for operating
the unit with the provided remote
control. When in “ II ” position the
unit is operated with the ON and
OFF buttons of the remote con-
trol.
When the switch is in the center
(“O”) position the unit is off.
B - Low Heat On/Off Switch
The Low Heat On/Off Switch
supplies power to the heater fan
Figure 1
Operation
and the heater element. When the
switch is in the ON position the
heater operates on LOW.
C - High Heat Switch
The High Heat On/Off Switch
supplies power to the heater fan
and the heater element, when the
switch is in the ON position the
heater operates on HIGH. The
Low Heat Switch must also be in
the ON position for the high heat
setting to operate.
!NOTE: The heater on your
replace may emit a slight,
harmless odor when rst used.
This odor is a normal condition
caused by the initial heating of
internal heater parts and will
not occur again.
Resetting the Temperature Cut-
off Switch
The heater is protected with a
ABC
10 www.dimplex.com
Operation
safety device to prevent overheat-
ing. Should the heater overheat,
an automatic cut out will turn the
heater off and it will not come
back on without being reset. It
can be reset by switching the
3-Position Switch (Figure 1A) to
Off (“ O” position) and waiting
ve minutes before switching the
unit back on.
CAUTION: If you need to
continuously reset the heater,
unplug the unit and call your
local dealer.
Remote Control (Figure 2)
The replace is supplied with an
integrated On/Off remote control.
!NOTE: Ensure that the re-
place’s 3-Position Switch is set
to the remote control setting
(“II” position).
To operate, push the ON button
to turn replace on, push the OFF
button to turn the replace off.
!NOTE: Before attempting any
operation with the remote, pull
the plastic insulator strip out
from between the remote cas-
ing and battery cover
Remote Control Initialization/
Reprogramming
In the event that your remote
control ceases to operate your
replace, follow these steps to
re-initialize the remote controland
the remote control receiver in the
replace:
1. Place the 3-Position Switch
(Figure 1A) in the Off (“ O”)
position.
2. Wait a minimum of ve sec-
onds and then place the
3-Position Switch in the Re-
mote Control (“ II ”) position.
3. Within 10 seconds of chang-
ing the switch position, press
the ON button located on the
remote control (Figure 2).
This will synchronize the remote
control and the replace receiver.
!NOTE: You will have only 10
seconds to perform this last
step. Failure to do so will result
Figure 2
Off
Button
On
Button
Battery
cover
Plastic
strip
Other manuals for DFI2310
1
This manual suits for next models
1
Table of contents
Languages:
Other Dimplex Indoor Fireplace manuals
Dimplex
Dimplex BLF50 User manual
Dimplex
Dimplex DFB4047 User manual
Dimplex
Dimplex CASSETTE 400 User manual
Dimplex
Dimplex 6901860100 Quick start guide
Dimplex
Dimplex DNV20AB User manual
Dimplex
Dimplex RANA LED User manual
Dimplex
Dimplex Revillusion RBF30-FG User manual
Dimplex
Dimplex BAR20-AU User manual
Dimplex
Dimplex DNV20AB User manual
Dimplex
Dimplex CHERITON LOG User manual
Dimplex
Dimplex DF2690 User manual
Dimplex
Dimplex TOLUCA TLC20 Instruction Manual
Dimplex
Dimplex VVT75 Instruction Manual
Dimplex
Dimplex DFI23096A User manual
Dimplex
Dimplex 6908760100 User manual
Dimplex
Dimplex Electric fireplaces User manual
Dimplex
Dimplex DWOP20R User manual
Dimplex
Dimplex Auvergne Log 2920 User manual
Dimplex
Dimplex DFP6848 User manual
Dimplex
Dimplex Revillusion Osbourne User manual
Popular Indoor Fireplace manuals by other brands
Brigantia
Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual
Nordpeis
Nordpeis Bergen Installation and user manual
Superior
Superior BCT2536TMN Installation and operation instructions
Quadra-Fire
Quadra-Fire 5100I-GD-B owner's manual
Renaissance
Renaissance RUMFORD 1000 user manual
Lacunza
Lacunza IV-800 Instruction book
Baxi
Baxi 940 Installer and owner guide
Dru
Dru Maestro 60/2 Tall RCH installation manual
Diamond Fireglass
Diamond Fireglass SS-O22 General assembly, installation, and operation instructions
HearthStone
HearthStone Windsor Bay 8830 Owner's manual and installation guide
Napoleon
Napoleon ASCENT B42 quick start guide
Enviro
Enviro E33GI owner's manual
Smeg
Smeg L30 FABE Installation & user's instructions
KEDDY
KEDDY K700 Installation instructions care and firing instructions
Godin
Godin 3451 manual
Jøtul
Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions
Austro Flamm
Austro Flamm Heidi Back 2.0 945048 operating manual
Desa
Desa CCFPDFT Owner's operating & installation manual