Digitus DN-82060 User manual
Fast Ethernet PoE +
VDSL Extender Set
Manual
DN-82060
Ethernet Extender
This Ethernet extender consists of one Transmitter-Unit and one Receiver-Unit.
It can transfer Ethernet signal and power synchronously to extend signal
though coaxial cable or network cable over a distance of 500m. The
transmitter could be powered with 54V DC or PoE. It is widely used in coaxial
cable and network cable mixed wiring security surveillance and network
rebuilding project.
Feature
1) The equipment consists of two parts: Transmitter unit (called SV) and
Receiver unit (called IPC). Transmitter has 48-57V DC port, one PoE
input port and two output ports: BNC and RJ45; Receiver has two input
ports: BNC and RJ45, one PoE output port
2) Extend signal and power up to 500m though coaxial cable or 400m
though network cable
3) Ethernet delay less than 1ms; meet point to point application
4) Standard: IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX,
IEEE802.3af/at
5) Protection: excellent circuit isolation protection, superior product
anti-thunder, anti-static and anti-interference ability
6) Appearance: solid and delicate, meet MIT rack installation standard,
working temperature: 0℃～55
7) Installation: Plug-and-play, no setting required
Notice
Please use 75-5 standard or above coaxial cable and Cat5e/6 cable to get
the longest transmission distance!
Board diagram
Description
Installation steps
Please check the following items before installation. If any missing, please
contact the dealer.
EthernetExtender 1pc
MIT Hangers 2 pcs
User Manual 1 pc
Please follow below the installation steps:
1) Please turn off the signal source and the device's power, installation with
power on may damage the device;
2) Check if the network cable and other transmission line that will be used is
not occupied by other device;
3) Use a network cable to connect PoE IN port of transmitter and PoE
Ethernet switch (if it's not PoE equipment, then need to use 48-54v power
adapter), use another network cable or coaxial cable to connect EPOC
port of transmitter and EPOC port of receiver;
4) Use a network cable to connect IP camera with PoE out port of receiver;
5) Check if the installation is correct; make sure all the connection are
reliable and power up the system;
Specification
Product is subject to change without prior notice.
Trouble Shooting
1) Please check if the RJ45 cable order is in accordance with the
EIA/TIA568A or 568B industry standards
2) The maximum transmission distance depends on the signal source and
cable quality; please do not exceed the maximum transmission distance
3) Please replace a failure device with a proper one to check if the device is
broken
4) If the problem still exists, please contact the factory
Table 1
Picture 1
Description:
The test data in table1 gained through the test method in Picture 1
Table of contents
Other Digitus Extender manuals
Digitus
Digitus DN-95121 User manual
Digitus
Digitus DS-55204 User manual
Digitus
Digitus DA-70141 User manual
Digitus
Digitus DN-95126 User manual
Digitus
Digitus DS-53200 User manual
Digitus
Digitus DS-55505 User manual
Digitus
Digitus DS-55502 User manual
Digitus
Digitus DS-51200 User manual
Digitus
Digitus DS-55516 User manual
Digitus
Digitus DC-56100 User manual
Digitus
Digitus DS-55203 User manual
Digitus
Digitus DS-55100-1 User manual
Digitus
Digitus DS-55508 User manual
Digitus
Digitus DS-55400 User manual
Digitus
Digitus DS-55200 User manual
Digitus
Digitus DS-55522 User manual
Digitus
Digitus DS-55520 User manual
Digitus
Digitus DS-55126 User manual
Digitus
Digitus DS-55100 User manual
Digitus
Digitus DN-82040 User manual
