DeVilbiss SB-E-2-534 User manual

EP 1 - 10

SB-E-2-534

Operation Manual

Advanced - Conventional Gravity

Feed Spraygun

ISS.02

Operation Manual

COMPACT – Gravity Feed Spraygun

Important

Read and follow all instructions and Safety Precautions before using this

equipment

Description

The Compact Gravity feed Spraygun Kit complies to ATEX regulations 94/9/EC, protection

level; II 2 G X, Suitable for use in Zones 1 and 2

Important: : These Sprayguns are suitable for use with solvent based materials. These guns

are not designed for use with highly corrosive and/or abrasive materials and if used with such

materials it must be expected that the need for cleaning and/or replacement of parts will be

increased. If there is any doubt regarding the suitability of a specific material contact your local

Distributor or ITW Finishing direct.

Model Part Number

Example: COM-G430-16

Aircap Fluid nozzle size

(16 = 1,6 mm)

ITW Finishing Systems and Products reserve the right to modify equipment specification without

prior notice.

EC Declaration of Conformity

We: ITW Finishing UK, Ringwood Rd, Bournemouth, Dorset, BH11 9LH, UK, as the

manufacturer of the Spraygun model Compact, declare, under our sole responsibility, that the

equipment to which this document relates is in conformity with the following standards or other

normative documents:

BS EN 292-1 PARTS 1 & 2: 1991, BS EN 1953: 1999; and thereby conform to the

protection requirements of Council Directive 98/37/EC relating to Machinery Safety Directive,

and;

EN 13463-1:2001, council Directive 94/9/EC relating to Equipment and Protective

Systems intended for use in Potentially Explosive Atmospheres protection level II 2 G X.

B. Holt, General Manager

30th June 2003

SAFETY WARNINGS

Fire and explosion

Solvents and coating materials

can be highly flammable or

combustible when sprayed. ALWAYS

refer to the coating material suppliers

instructions and COSHH sheets

before using this equipment

Users must comply with all local

and national codes of practice

and insurance company

requirements governing

ventilation, fire precautions, operation

and house-keeping of working areas

This equipment, as supplied,

is NOT suitable for use with

Halogenated Hydrocarbons.

Static Electricity can be

generated by fluid and/or air

passing through hoses, by the

spraying process and by cleaning non-

conductive parts with cloths. To prevent

ignition sources from static discharges,

earth continuity must be maintained to

the spraygun and other metallic

equipment used. It is essential to use

conductive air and/or fluid hoses.

Personal Protective

Equipment

Toxic vapours – When sprayed,

certain materials may be

poisonous, create irritation or be

otherwise harmful to health.

Always read all labels and safety data

sheets for the material before spraying

and follow any recommendations. If In

Doubt, Contact Your Material Supplier

The use of respiratory protective

equipment is recommended at all

times. The type of equipment

must be compatible with the material

being sprayed.

Always wear eye protection when

spraying or cleaning the spraygun

Gloves must be worn when

spraying or cleaning the

equipment

Training – Personnel should be given

adequate training in the safe use of

spraying equipment.

Misuse

Never aim a spraygun at any part of the

body

Never exceed the max. recommended

safe working pressure for the equipment

The fitting of non-recommended or non-

original spares may create hazards

Before cleaning or maintenance, all

pressure must be isolated and relieved

from the equipment

The product should be cleaned using a

gun washing machine. However, this

equipment should not be left inside gun

washing machines for prolonged periods

of time.

Noise Levels

The A-weighted sound level of

sprayguns may exceed 85 dB

(A) depending on the set-up

being used. Details of actual

noise levels are available on request. It is

recommended that ear protection is worn

at all times when spraying.

Operating

Spray Equipment using high pressures

may be subject to recoil forces. Under

certain circumstances, such forces could

result in repetitive strain injury to the

operator.

Parts List

Ref. No Description Part Number Qty Options

1 Air Cap/Retaining ring

COM-510 SP-100-430-K 1

+ 2 Nozzle SP-200S-**-K 1 13,16,18,20

e.g ** =16 =1.6 mm

+ 3 Separator SP-626-K5 5

+ 4 Packing GTI-445-K2 2

5 Spreader Valve SP-403-K 1

6 Stud and Screw GTI-408-K5 5

7 Needle Adjusting Screw SP-614-K 1

+ 8 Spring SP-622-K5 1

+ 9 Needle SP-300S-**-K 1 13,16,18,20

e.g ** =16 =1.6 mm

10 Airvalve housing + seal SP-612-K 1

+ 11 Spindle - 1

12 Trigger SP-617-K 1

13 Connector SP-611-K 1

14 Airflow Valve SP-402-K 1

15 Drip Check Lid kit of 5 GFC-2-K5 1

+ 16 Air Valve Service Kit SPK-101-K 1

17 Retaining Ring and Seals SPK-102-K 1

18 Spreader/ Cheater Service Kit GTI-428-K5 5

19 Circlip 25746-007-K5 5

20 Cup Lid GFC-402 1

21 Filter KGP-5 1

22 1/2 Ltr Gravity Cup Kit GFC-501 1

23 Air Valve assembly Tool 1

24 Spanner SPN-5 1

Spraygun Service Kit

(parts included marked + ) SPK-401-** 1 13,16,18,20

e.g ** =16 =1.6 mm

Patent No 2372465 (GB)

Air supply connection - Universal 1/4“ BSP and NPS

Maximum static Air inlet pressure - P1= 12 bar (175 psi)

Nominal gun Air inlet pressure -

with gun triggered

3 bar (44 psi)

Maximum Service temperature 40°C

Gun Weight - 583 g

Materials of Construction

Gun body Anodised Aluminium

Nozzle Stainless Steel

Needle Stainless Steel

Fluid Inlet Stainless Steel / PTFE

Trigger Nickel Plated Steel

Cup Acetal (Anti-static)

Cup Lid Acetal (Anti-static)

Specification

Installation

Important: To ensure that this equipment

reaches you in first class condition,

protective coatings have been used.

Flush the equipment through with a

suitable solvent before use.

1. Attach air hose to connector (13).

Recommended hose size 8 mm bore.

The hose must be conductive and

electrical bond from the spraygun to

earth should be checked with an

ohmeter. A resistance of less than

106Ohms is recommended.

2. Air supply should be filtered and

regulated.

3. Attach Cup assembly (22) by

screwing into the Fluid Inlet of the

spraygun. Tighen when fully home.

1. Turn off air and relieve pressure in

the supply lines, or if using QD

system, disconnect from airline.

2. Remove Cup Lid (20 )and empty

coating material into a suitable

container. Clean the gun and cup,

preferably in a gun wash machine.

Clean the cup.

3. Check the breather hole in the Lid

and the Drip Check Lid is not

blocked.

4. Remove air cap (1) and clean. If any

of the holes in the cap are blocked

with coating material use a toothpick

to clean. Never use metal wire which

could damage the cap and produce

distorted spray patterns

5. Ensure the tip of the nozzle (2) is

Preventative Maintenance

Operation

1. Mix coating material to manufacturers

instructions.

2. Fill the cup with the required amount

of material. Fill to no more than 25mm

(1“) from the top of the cup. DO NOT

OVERFILL.

3. Attach Cup Lid.

4. Turn needle adjusting screw (7)

clockwise to prevent movement.

5. Turn spreader valve (5) counter-

clockwise to fully open.

6. Adjust inlet air pressure to give 3 bar

(44 psi) at the gun inlet with the gun

triggered. (pressure gauge attachment

shown under Accessories is

recommended for this).

7. Turn needle adjusting screw counter

clockwise until first thread shows.

8. Test spray. If the finish is too dry

reduce airflow by reducing air inlet

pressure or by the Airflow Valve (14).

Screw the Adjusting Knob (14) in to

reduce pressure.

9. If finish is too wet reduce fluid flow by

turning needle screw (7) clockwise. If

atomisation is too coarse, increase

inlet air pressure. If too fine reduce

inlet pressure.

10. The pattern size can be reduced by

turning adjusting valve (5) clockwise.

11. Hold gun perpendicular to surface

being sprayed. Arcing or tilting may

result in uneven coating.

12. The recommended spray distance is

150-200 mm (6”-8”).

13. Spray edges first. Overlap each stroke

a minimum of 50%. Move gun at a

constant speed.

14. Always turn off air supply and relieve

pressure when gun is not in use.

clean and free from damage. Build

up of dried paint can distort the

spray pattern.

6. Lubrication – stud/screw (6), needle

(9) and air valve (11) should be

oiled each day.

Nozzle (2) and Needle (9) – Remove

parts in the following order: 7, 8, 9, 1

and 2. Replace any worn or damaged

parts and re-assemble in reverse order.

Recommended tightening torque for

nozzle (2) 9.5-12 Nm (80-100 lbf in).

Packing – Remove parts 7, 8, 9.

Unscrew cartridge (4). Fit new cartridge

finger tight. Re-assemble parts 9, 8,

and 7 and tighten cartridge (4) with

spanner sufficient to seal but to allow

free movement of needle. Lubricate

with gun oil.

Air Valve Seal Kit (16) - (Refer to

photos 1 to 28 and fig 2)

1. Remove Adjusting Knob (7), Spring

(8), and Needle (9).

2. Loosen Housing (10).

3. Remove Housing (10) and Airvalve

Spring.

4. Remove Valve (11).

5. Using Service Tool SPN-7, engage

groove behind the Valve Seat.

6. Remove Valve Seat.

7. Push out the Front Airvalve Seal

with a finger.

8. Turn the Gun upside down and let

the Seal fall out.

9. Fit New Front Seal to Service Tool.

10. Fit new Seal to gunbody and press

firmly to ensure Seal is engaged.

11. Fit New Valve Seat to Service Tool.

Groove must face outwards.

12. Fit Valve Seat to Gunbody.

13. Remove Rear Airvalve Seal from

housing (10) with a hooked

instrument.

14. Fit new Seal to Service Tool.

15. Fit Seal to Housing (10).

16. Replace Valve (11).

17. Replace Valve Spring and screw in

Housing (10).

18. Tighten Housing.

19. Fit Needle (9).

20. Fit Spring (8) and Knob (7).

21. Adjust Needle Packing (4) with

Spanner sufficient to seal but to

allow free movement of needle.

Lubricate with gun oil.

Spreader valve (5) – Caution: always

ensure that the valve is in the fully open

position by turning screw fully counter-

clockwise before fitting to body.

Air cap / Nozzle Selection

Refer to coating material manufacturers

recommendations or ITW Finishing UK

Website:

www.itweuropeanfinishing.com

Replacement of Parts

FIG 2

1 2

3 4

5 6

7 8

9 10

11 11a

12 13

14 15

18 19

20 21

This manual suits for next models

Table of contents

Other DeVilbiss Paint Sprayer manuals

DeVilbiss

DeVilbiss SB-21-058-H User manual

DeVilbiss

DeVilbiss GTI-600G User manual

DeVilbiss

DeVilbiss AGX-552 User manual

DeVilbiss

DeVilbiss ADVANCE HD HVLP Series User manual

DeVilbiss

DeVilbiss NEPTUNE Series User manual

DeVilbiss

DeVilbiss AGN-502 User manual

DeVilbiss

DeVilbiss JGA PRO Series Service manual

DeVilbiss

DeVilbiss JGA-504 Reference manual

DeVilbiss

DeVilbiss SGA-570 User manual

DeVilbiss

DeVilbiss AG360 Series User manual

DeVilbiss

DeVilbiss FLG3 User manual

DeVilbiss

DeVilbiss Compact MINI Service manual

DeVilbiss

DeVilbiss GTI User manual

DeVilbiss

DeVilbiss GTI PRO LITE User manual

DeVilbiss

DeVilbiss TRANS-TECH PRESSURE FEED User manual

DeVilbiss

DeVilbiss JGP-504 User manual

DeVilbiss

DeVilbiss GTI-520P Reference manual

DeVilbiss

DeVilbiss TGC-545 User manual

DeVilbiss

DeVilbiss EXL-620G User manual

DeVilbiss

DeVilbiss KK-5025 Reference manual

DeVilbiss

DeVilbiss TEKNA PRO LITE Service manual

DeVilbiss

DeVilbiss MSHTE Series Reference manual

DeVilbiss

DeVilbiss COBRA 3C User manual

DeVilbiss

DeVilbiss Viper User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

Graco

Graco HydroShield WMBH00 Instructions - parts