DeVilbiss MSA-510-DEC Reference manual

SB-2-319-C

IMPORTANT: Before using this equip-

ment, read all safety precautions and

instructions. Retain for future use.

DESCRIPTION

The MSA-510-DEC is a smaller, lighter

weight gun that can apply decorative

spatter effects to wood furniture, metal

panels, etc. Finish may be changed

from a fine mist to larger droplet size

particles. Simply adjust fluid pressure

and/or air pressure

The MSA-510-DEC comes with the

flat-end AV-447 spatter cap assembly.

Small spatter dots are the result of

coarse atomization when using the

standard spatter cap assembly (2).

OPERATION

Note

This gun may be used with

chlorinated solvents. Alumi-

num is not used in the fluid

passage areas.

Mixmaterialaccordingtomanufacturer's

instructions. Itmay be necessary to strain

material.

A greater than normal gun distance

provides a more uniform particle size.

Particlespacingisdeterminedbyspeed

of movement and degree of overlap.

Particle size is dependent on the mate-

rial consistency. Specially formulated

spattermaterialsareavailable,although

standard paints may be used. Apply

standard paints using very little or no

reduction.

Pressure on cup or tank controls mate-

rial flow. Begin with the adjusting

screw (31) wide open. Use adjusting

screw (31) to regulate material flow

under abnormally low material pres-

sure or material viscosity conditions.

SERVICE BULLETIN

MSA-510-DEC DECORATOR SPRAY GUN

Replaces SB-2-319-B

Repair Kit KK-4987-2

Adjust atomization air to get desired

particle size. It should be high enough

to carry particles to surface. Spatter

dot size increases with pressure reduc-

tion, and decreases with pressure in-

crease. Pressure used depends on

material viscosity being sprayed and

desired operation speed.

PREVENTIVE MAINTENANCE

To clean gun passages, blow back

paint to material supply source and

flush fluid passage with clean solvent.

Model HD-503 Gun/Hose Cleaner is a

very fast and effective way of cleaning

(See Accessories). Wipe gun clean

with solvent soaked cloth.

If slots of ring (4) become clogged,

clean by soaking cap in solvent and

scrubbing with a gun cleaning brush.

Note

When replacing the fluid tip or

fluid needle, replace both at

the same time. Using worn

parts can cause fluid leakge.

Also, replace the needle pack-

ing at this time.

Using SSL-10 gun lube, lightly lubri-

cate the threads of the fluid tip before

reassembling. Torque to 20-25 ft. lbs.

To prevent damage to the fluid

tip (7) or fluid needle (28), be

sure to either 1) pull the trigger

and hold while tightening the

fluid tip or 2) remove fluid

needle adjusting screw to re-

lieve spring pressure.

DBA

Spray Gun Lubrication

For best results, lubricate the points

indicated, daily. Use SSL-10 Spray

Gun Lube to lubricate.

A. Trigger Points

B. Packings

C . Adjusting Valves

D. Air Baffle Threads

Page 2 SB-2-319-C

HAZARD CAUSE SAFEGUARDS

Fire Solvent and coatings can be highly Adequate exhaust must be provided to keep

flammable or combustible, especially air free of accumulations of flammable vapors.

when sprayed.

Smoking must never be allowed in the spray area.

Fire extinguishing equipment must be present

in the spray area.

Solvent Spray During cleaning and flushing, sol- Wear eye protection.

vents can be forcefully expelled

from fluid and air passages. Some

solvents can cause eye injury.

Inhaling Toxic Substances Certain materials may be harmful Follow the requirements of the Material Safety

if inhaled, or if there is contact Data Sheet supplied by your coating material

with the skin. manufacturer.

Adequate exhaust must be provided to keep the

air free of accumulations of toxic materials.

Use a mask or respirator whenever there is a

chance of inhaling sprayed materials. The mask

must be compatible with the material being

sprayed and its concentration. Equipment must

be as prescribed by an industrial hygienst or safety

expert, and be NIOSH approved.

Explosion Hazard - Halogenated hydrocarbon solvents This gun can be used with these solvents.

- for example; methylene chloride However, aluminum is widely used in other spray

and 1, 1, 1 - Trichloroethane can application equipment - such as, material pumps,

chemically react with aluminum. cups, regulators, valves, etc. Check all other equip-

The chemical reaction caused by ment items before use and make sure they can

these solvents reacting with aluminum also be used safely with these solvents. Read the

can become violent and lead to an label or material data sheet for the material you

equipment explosion. intend to spray. If in doubt as to whether or not a

coating or cleaning material is compatible, contact

your material supplier.

SAFETY PRECAUTIONS

This manual contains information that is improtant for you to know and understand. This information relates to USER SAFETY and

PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the following symbols. Please pay particular

attention to these sections.

Important information that tells how to

prevent damage to equipment, or how

to avoid a situation that may cause

minor inury.

Note

Information that you should pay spe-

cial attention to.

Important safety information - A hazard

that may cause serious injury or loss of

life.

The following hazards may occur during the normal use of this equipment.

Please read the following chart before using this equipment.

SB-2-319-C Page 3

Note

*Apply QH-130 (Loctite #242,

med. strength blue) sealing com-

pound onto the threads and

screw into place with 170-180 in/

lb. torque.

28 22 29 30 31

Ref. Individual

No. Part No. Description Parts Req.

1 MBC-231 Retaining Nut 1

2 AV-447 Spatter Cap Assembly (Flat) 1

3 --- Cap 1

4 --- Ring 1

5 --- Gasket 1

6 MSV-3-K10 Gasket, Teflon (Blue) (Kit of 10) 1

7 JGA-4040-VF Fluid Tip and Needle, Lapped 1

(Includes Item 28)

8 --- Lock Nut 1

9 --- Nipple 1

10 JGA-4044 Fluid Inlet and Nut Kit 1

•11 JGV-463-K3 Needle Packing (Kit of 3) 1

34411-122-K10

Packing Gland (Kit of 10) 1

13 --- Trigger Bearing Stud 1

•14 --- Screw 1

15 JGS-478 Stud and Screw Kit 1

(3 studs and 5 screws in kit)

16 JGA-477 Trigger, Stud and Screw Kit 1

(Kit includes 1 each)

•17 JGA-14-K25 Snap Ring (Kit of 25) 1

•18 JGA-15-K25 Washer (Kit of 25) 1

•19 JGS-26-K25 U Cup Seal (Kit of 25) 1

•20 JGS-431-K25 Air Valve (Kit of 25) 1

•21 MBD-12-K25 Spring (Kit of 25) 1

•22 JGS-72-K10 Gasket (Kit of 10) 2

23 JGS-449-1 Air Valve Assembly 1

24 JGA-132 Plug 2

PARTS LIST

Ref. Individual

No. Part No. Description Parts Req.

25 MSA-3 Nipple 1

•26 JGD-14-K10 Gasket (Kit of 10) 1

27 JGA-4001 Baffle and Gasket Kit 1

28 --- Fluid Needle (Included with

Item 7) 1

29 --- Bushing 1

•30 MBD-19-K10 Spring (Kit of 10) 1

•31 --- Spring Pad (Included

with Item 30) 1

32 TGHV-15 Adjusting Knob 1

33 JGA-4041 Bushing, Spring & Knob Kit 1

•These parts are included in Repair Kit KK-4987-2 and should be

kept on hand for service convenience.

Suffixes - K5, K10 designate kits of multiple parts.

(Example) JGV-463-K3 is a kit of 3 packings.

912

17 19 20 21

▲

Torque to

20-25 ft. lbs.

726 24

(Ref. No. 11) Needle

Packing (2 piece pack-

ing) covered by U.S.

Patent No. 5,209,501.

+Tapered edge faces out

towards packing nut.

▲

Fluid Packing

Nut

+Inner Teflon

Piece

Fluid

Needle

Outer U.H.M.W.

Poly. Piece

Page 4 SB-2-319-C

WARRANTY

This product is covered by DeVilbiss' Industrial 1 Year Limited Warranty.

See SB-1-000 which is available upon request.

Contains all necessary

tip, hose and nut sizes

used on or with gun.

WR-103 WRENCH HD-503

SOLVENT SAVER™

GUN/HOSE CLEANER

These brushes are help-

ful in cleaning threads

and recesses of gun

body.

42884-214-K5 3/8"

42884-215-K10 5/8"

CLEANING BRUSHES

Compatible with all paint

materials: contains no sili-

cone or petroleum distil-

lates to contaminate paint

An MSDS Sheet is avail-

able upon request.

SPRAY GUN LUBE

SSL-10-K12

(2 oz. bottle)

HAV-500 does not have

pressure gauge. Use to

control air usage at gun.

HAV-500 OR

HAV-501

Adjusting Valve

(HAV-501 SHOWN)

ACCESSORIES

2 qt. Hose/Gun Cleaner

used to clean the inside

of hose, fluid passage-

ways of gun and other

paint equipment.

HARG-510 AIR

REGULATOR

Use to maintain nearly

constant outlet pressure

despite changes in inlet

pressure and down-

stream flow.

DeVILBISS WORLDWIDE SALES AND SERVICE LISTING - www.devilbiss.com

INDUSTRIAL FINISHING

DeVilbiss has authorized distributors throughout the world. FOR TECHNICAL ASSISTANCE OR THE DISTRIBUTOR

NEAREST YOU, CALL TOLL FREE 1-888-992-4657 (U.S.A. AND CANADA ONLY). FOR LOCAL CALLS, SEE LISTING

BELOW.

U.S./Canada Sales and Customer Service Office Address Telephone No.

GLENDALE HEIGHTS, IL 60139 195 Internationale Blvd. (630) 237-5000

Toll Free Fax No.1-877-790-6965

Other DeVilbiss Paint Sprayer manuals

DeVilbiss

DeVilbiss TRANS-TECH GRAVITY FEED User manual

DeVilbiss

DeVilbiss SRI-2-12-K User manual

DeVilbiss

DeVilbiss FLG-G5-14 User manual

DeVilbiss

DeVilbiss MBC-ZINC Reference manual

DeVilbiss

DeVilbiss GTI User manual

DeVilbiss

DeVilbiss COMPACT COM-G430-16 User manual

DeVilbiss

DeVilbiss HVLP Gravity Feed Spraygun User manual

DeVilbiss

DeVilbiss Cobra 1 User manual

DeVilbiss

DeVilbiss JJ-K Series User manual

DeVilbiss

DeVilbiss FUNCY JGX-3C-343 User manual

DeVilbiss

DeVilbiss FLG-615-114 Reference manual

DeVilbiss

DeVilbiss EGA-503 User manual

DeVilbiss

DeVilbiss GTI User manual

DeVilbiss

DeVilbiss LUNA-MARKII-R-PLUS User manual

DeVilbiss

DeVilbiss SRi-628 Reference manual

DeVilbiss

DeVilbiss MSV-531-28FF Reference manual

DeVilbiss

DeVilbiss JGX-502 User manual

DeVilbiss

DeVilbiss JGA-510 User manual

DeVilbiss

DeVilbiss Compact-I User manual

DeVilbiss

DeVilbiss TGC-536 User manual

DeVilbiss

DeVilbiss AGF-508 User manual

DeVilbiss

DeVilbiss MSV-512 User manual

DeVilbiss

DeVilbiss EXL-520S User manual

DeVilbiss

DeVilbiss JGA-503 User manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

Graco

Graco HydroShield WMBH00 Instructions - parts