Desa CGEFP33PRB Quick start guide

Save this manual for future reference.

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a ﬁre or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

— Installation and service must be performed by a quali-

ﬁed installer, service agency or the gas supplier.

UNVENTED (VENT-FREE) GAS FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

CGEFP33PRB, CGEFP33NRB

EFP33PRB, EFP33NRB

Gas Fireplace with Total Control System (TCS)

Shown with optional

hearth base accessory.

www.desatech.com 111245-01B

WARNING: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual for correct installation

and operational procedures. For assistance or addi-

tional information consult a qualiﬁed installer, service

agency or the gas supplier.

WARNING: This is an unvented gas-ﬁred heater. It uses

air (oxygen) from the room in which it is installed. Provi-

sions for adequate combustion and ventilation air must

be provided. Refer to Air for Combustion and Ventilation

section on page 6 of this manual.

This appliance may be installed in an aftermarket,* per-

manently located, manufactured (mobile) home, where

not prohibited by local codes.

This appliance is only for use with the type of gas indi-

cated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

State of Massachusetts: The installation must be made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-ﬁred supplemental room heaters shall provide to each

purchaser a copy of 527 CMR 30 upon sale of the unit.

Vent-free gas products are prohibited for bedroom and bathroom installation in the Common-

wealth of Massachusetts.

TABLE OF CONTENTS

Safety Information ............................................... 3

Product Identiﬁcation ........................................... 4

Local Codes ........................................................ 5

Unpacking ........................................................... 5

Product Features ................................................. 5

Air for Combustion and Ventilation ...................... 6

Installation ........................................................... 8

Operating Fireplace ........................................... 25

Inspecting Burners ............................................ 28

Cleaning and Maintenance ................................ 29

Troubleshooting ................................................. 30

Speciﬁcations .................................................... 33

Service Hints ..................................................... 33

Technical Service .............................................. 33

Illustrated Parts Breakdown and Parts List ....... 34

Replacement Parts ............................................ 40

Accessories ....................................................... 40

Wiring Diagram .................................................. 42

Templates .......................................................... 43

Parts Central ..................................................... 45

www.desatech.com

111245-01B 3

SAFETY INFORMATION

WARNING: This product con-

tains and/or generates chemicals

known to the state of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this ﬁreplace.

Improper use of this ﬁreplace

can cause serious injury or

death from burns, ﬁre, explo-

sion, electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the ﬂu, with head-

aches, dizziness or nausea. If you have these signs,

the heater may not be working properly. Get fresh

air at once! Have heater serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the inﬂuence

of alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and pro-

pane/LP gases are odorless. An odor-making agent

is added to the gas. The odor helps you detect a gas

leak. However, the odor added to the gas can fade.

Gas may be present even though no odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not ap-

proved for use with this heater.

WARNING: Do not allow fans

to blow directly into the ﬁreplace.

Avoid any drafts that alter burner

ﬂame patterns. Ceiling fans can

create drafts that alter burner

ﬂame patterns. Altered burner

patterns can cause sooting.

Due to high temperatures, the

appliance should be located out

of trafﬁc and away from furniture

and draperies.

Do not place clothing or other

ﬂammable material on or near

the appliance. Never place any

objects on the heater.

Fireplace front and screen be-

come very hot when running ﬁre-

place. Keep children and adults

away from hot surface to avoid

burns or clothing ignition. Fire-

place will remain hot for a time

after shutdown. Allow surfaces

to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with heater. When using the hand-

held remote accessory keep se-

lector switch in the OFF position

to prevent children from turning

on burners with remote.

You must operate this ﬁreplace

with the ﬁreplace screen and

hood in place. Make sure ﬁre-

place screen and hood are in

place before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other ﬂam-

mable vapors and liquids.

www.desatech.com 111245-01B

1. This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors (propane/LP units only).

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighborʼs phone. Follow the gas supplierʼs

instructions

• if you cannot reach your gas supplier, call

the ﬁre department

4. This ﬁreplace shall not be installed in a bed-

room or bathroom.

5. Do not use this ﬁreplace as a wood-burning

ﬁreplace. Use only the logs provided with the

ﬁreplace.

6. Do not add extra logs or ornaments such as

pine cones, vermiculite or rock wool. Using

these added items can cause sooting. Do not

add lava rock around base. Rock and debris

could fall into the control area of ﬁreplace.

7. To prevent the creation of soot, follow the instruc-

tions in Cleaning and Maintenance, page 29.

8. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

9. This ﬁreplace needs fresh air ventilation to run

properly. This ﬁreplace has an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the ﬁreplace if not enough

fresh air is available. See Air for Combustion

and Ventilation, page 6. If ﬁreplace keeps

shutting off, see Troubleshooting, page 30.

10. Do not run ﬁreplace

• where ﬂammable liquids or vapors are used

or stored

• under dusty conditions

11. Do not use this ﬁreplace to cook food or burn

paper or other objects.

12. Do not use ﬁreplace if any part has been exposed

to or under water. Immediately call a qualiﬁed

service technician to inspect the ﬁreplace and to

replace any part of the control system and any

gas control which has been under water.

SAFETY INFORMATION

Continued

13. Do not operate ﬁreplace if any log is broken.

Do not operate ﬁreplace if a log is chipped

(dime-sized or larger).

14. Turn ﬁreplace off and let cool before servicing.

Only a qualiﬁed service person should service

and repair ﬁreplace.

15. Operating ﬁreplace above elevations of 4,500

feet could cause pilot outage.

16. To prevent performance problems with pro-

pane/LP units, do not use propane/LP fuel

tanks of less than 100 lb. capacity.

17. Provide adequate clearances around air

openings.

PRODUCT

IDENTIFICATION

Log Set

Wall Switch

Assembly

Piezo

Ignitor

Remote

Control

Manual

Override

Handle

Manual Ignition

Bypass Switch

Figure 1 - Fireplace Floor Assembly

Figure 2 - Fireplace

Top Louver Assembly

Firebox

Hood

Bottom Louver

Assembly

Screen

Assembly

Top Outer

Casing

Firebox

Support

Blower Assembly

(Optional)

www.desatech.com

111245-01B 5

LOCAL CODES

Install and use ﬁreplace with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

CAUTION: Do not remove the

data plates attached to the heater

base assembly. The data plates

contain important warranty and

safety information.

1. With utility knife, cut the carton all the way

around above the staples on the bottom tray.

Lift the carton off the heater. Remove packing.

Note: The hood is located in the packing on

the right hand side of the heater front. Lift the

heater off the bottom tray.

2. Locate two screws above top corners of the

ﬁreplace screen. Remove and discard these

screws. Lift ﬁreplace screen up and pull out

to remove.

3. Remove protective packaging applied to logs,

log base assembly and ﬁreplace.

4. Remove ﬁreplace hood from carton insert.

5. Check all items for any shipping damage. If

damaged, promptly inform dealer where you

bought ﬁreplace.

PRODUCT FEATURES

OPERATION

This vent-free ﬁreplace is clean burning. It requires

no outside venting. There is no heat loss out a

vent or up a chimney. Heat is generated by both

realistic ﬂames and glowing embers. When used

without the optional blower, the ﬁreplace requires

no electricity making it ideal for emergency

backup heat.

SAFETY DEVICE

This ﬁreplace has a pilot with an Oxygen Depletion

Sensing (ODS) safety shutoff system. The ODS/

pilot is a required feature for vent-free room heat-

ers. The ODS/pilot system shuts off the ﬁreplace

if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This ﬁreplace has a piezo ignitor. This system

requires no matches, batteries or other sources to

light ﬁreplace.

WIRELESS REMOTE CONTROL

This ﬁreplace features an infrared wireless remote

control. This control system can be used to auto-

matically light the pilot and adjust the burner ﬂame

height at the push of a button.

WIRED WALL-MOUNTED REMOTE

CONTROL

This ﬁreplace features a two-button wall switch as-

sembly with glowing LEDʼs. The wall switch per-

forms the same functions as the wireless hand-held

remote control with the added feature of LEDʼs for

visual feedback of operation and status.

OPTIONAL BLOWER ASSEMBLY

ACCESSORY

This ﬁreplace accepts an optional blower assembly

(not included). The GA3650T/GA3700T Series

blower operates thermostatically and features a

variable speed control. The GA3700/GA3750

Series operates manually and also features a vari-

able speed control. The blower circulates heated

air from the ﬁreplace into the room. Use of blower

is optional. See Accessories, page 40.

www.desatech.com 111245-01B

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conﬁned

space or unusually tight con-

struction unless provisions are

provided for adequate combus-

tion and ventilation air. Read the

following instructions to insure

proper fresh air for this and

other fuel-burning appliances

in your home.

Todayʼs homes are built more energy efﬁcient

than ever. New materials, increased insulation and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy efﬁ-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, ﬁreplaces, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classiﬁcations:

1. Unusually Tight Construction

2. Unconﬁned Space

3. Conﬁned Space

The information on pages 6 through 8 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

Unusually tight construction is deﬁned as

construction where:

a. walls and ceilings exposed to the out-

side atmosphere have a continuous

water vapor retarder with a rating of

one perm (6 x 10-11 kg per pa-sec-m2) or

less with openings gasketed or sealed

and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to

areas such as joints around window

and door frames, between sole plates

and ﬂoors, between wall-ceiling joints,

between wall panels, at penetrations

for plumbing, electrical and gas lines

and at other openings.

If your home meets all of these three

criteria, you must provide additional

fresh air. See Ventilation Air From

Outdoors, page 8.

If your home does not meet all of the three

criteria above, proceed to Determining

Fresh-Air Flow For Fireplace Location.

Conﬁned and Unconﬁned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA

54 deﬁnes a conﬁned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3 per kw) of the aggregate input

rating of all appliances installed in that space and

an unconﬁned space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of

all appliances installed in that space. Rooms com-

municating directly with the space in which the

appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconﬁned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

DETERMINING FRESH-AIR FLOW

FOR FIREPLACE LOCATION

Determining if You Have a Conﬁned or

Unconﬁned Space

Use this work sheet to determine if you have a

conﬁned or unconﬁned space.

Space: Includes the room in which you will

install ﬁreplace plus any adjoining rooms with

doorless passageways or ventilation grills between

the rooms.

www.desatech.com

111245-01B 7

AIR FOR COMBUSTION

AND VENTILATION

Continued

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 18 ft.

(width) x 8 ft. (ceiling height) = 2880 cu. ft.

(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2880 cu. ft. (volume of space) x 20 =

57,600 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free ﬁreplace ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas ﬁreplace logs ___________ Btu/Hr

Other gas appliances* + ___________ Btu/Hr

Total = ___________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater ________ Btu/Hr

Vent-free ﬁreplace + ________ Btu/Hr

Total = ________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 57,600 Btu/Hr (maximum the space

can support)

73,000 Btu/Hr (actual amount of

Btu/Hr used)

The space in the above example is a conﬁned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconﬁned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors, page 8.

C. Install a lower Btu/Hr ﬁreplace, if lower Btu/Hr

size makes room unconﬁned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an un-

conﬁned space. You will need no additional fresh

air ventilation.

WARNING: If the area in

which the ﬁreplace may be oper-

ated is smaller than that deﬁned

as an unconﬁned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conﬁned space. When ventilating to an adjoining

unconﬁned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the ﬂoor on the wall connecting

the two spaces (see options 1 and 2, Figure 3). You

can also remove door into adjoining room (see

option 3, Figure 3). Follow the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for

Combustion and Ventilation for required size of

ventilation grills or ducts.

40,000

33,000

73,000

Figure 3 - Ventilation Air from Inside

Building

Remove

Door into

Adjoining

Room,

Option

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Into Adjoining

Room,

Option 1

12"

www.desatech.com 111245-01B

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings:

one within 12" of the ceiling and one within 12"

of the ﬂoor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

AIR FOR COMBUSTION

AND VENTILATION

Continued

Figure 4 - Ventilation Air from Outdoors

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat.

Use this heater along with your

primary heating system. Do not

install this heater as your pri-

mary heat source. If you have a

central heating system, you may

run system’s circulating blower

while using heater. This will help

circulate the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

WARNING: A qualiﬁed ser-

vice person must install ﬁre-

place. Follow all local codes.

WARNING: Never install the

ﬁreplace

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing or other ﬂammable

objects are less than 42 inches

from the front, top or sides of

the ﬁreplace

• in high trafﬁc areas

• in windy or drafty areas

CAUTION: This ﬁreplace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to ﬁreplace. Installing

ﬁreplace next to vinyl or cloth

wall coverings or operating

ﬁreplace where impurities (such

as, but not limited to, tobacco

smoke, aromatic candles, clean-

ing ﬂuids, oil or kerosene lamps,

etc.) in the air exist, may discolor

walls or cause odors.

Note: Your ﬁreplace is designed to be used in zero

clearance installations. Wall or framing material

can be placed directly against any exterior surface

on the rear, sides or top of your ﬁreplace, except

where standoff spacers are integrally attached. If

standoff spacers are attached to your ﬁreplace,

these spacers can be placed directly against wall

or framing materials.

Use the dimensions shown for rough openings to

create the easiest installation (see Built-In Fire-

place Installation, page 21).

IMPORTANT: Vent-free heaters add moisture to

the air. Although this is beneﬁcial, installing ﬁre-

place in rooms without enough ventilation air may

cause mildew to form from too much moisture. See

Air for Combustion and Ventilation, page 6.

IMPORTANT: Make sure the ﬁreplace is level.

If ﬁreplace is not level, log set will not work

properly.

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP)

for your unit. If your gas supply is not correct, do

not install ﬁreplace. Call dealer where you bought

ﬁreplace for proper type ﬁreplace.

www.desatech.com

111245-01B 9

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

ELECTRICAL HOOKUP

This fireplace normally operates under 120

VAC/60 Hz line voltage. The electrical cord sup-

plied with your ﬁreplace is ﬁve feet in length. You

must locate ﬁreplace within reach of a 120 volt

grounded electrical outlet. If not, you must install

an electrical outlet within reach of the ﬁreplace

power cord. The GA3555 outlet accessory may

be used for built-in applications.

INSTALLATION CLEARANCES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

ﬂoor, ceiling and adjoining wall.

INSTALLATION

Continued

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top Left and Bottom

Right Sides and Rear

0" 16" 0"

Carefully follow the instructions below. This will

ensure safe installation.

Minimum Clearances For Side

Combustible Material, Side Wall and

Ceiling

A. Clearances from the side of the fireplace

cabinet to any combustible material and wall

should follow diagram in Figure 5.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and

protrudes 3 1/2" from the wall. This combus-

tible material must be 4" from the side of the

ﬁreplace cabinet (see Figure 5).

B. Clearances from the top of the ﬁreplace open-

ing to the ceiling should not be less than 42

inches.

Figure 5 - Minimum Clearance for

Combustible to Wall

*Minimum 16 inches from Side Wall

Example

INSTALLATION SEQUENCE

After unpacking ﬁreplace (see Unpacking, page 4),

we suggest that you install your ﬁreplace system

in the following sequence:

Removal of ﬁreplace ﬂoor assembly (required)

Electrical connections for power cord (required)

3. Relocating wall switch (optional)

4. Installing blower accessory (optional)

Connecting ﬁreplace to gas supply (required)

6. Checking gas connections (required)

7. Firebox installation, conventional or built-in

(required)

8. Installing brass perimeter trim (optional)

9. Installing ﬁreplace hood (required)

10. Installing logs (required)

11. Installing ﬁreplace screen (required)

Use the following instructions to complete

each step.

REMOVING FIREPLACE SCREEN

AND FLOOR ASSEMBLY

NOTICE: Shutoff gas supply

and disconnect heater from gas

supply if installing blower into

previously installed ﬁreplace.

Contact a qualiﬁed service per-

son to do this.

1. Remove ﬁreplace screen. Remove two screws

that hold ﬁreplace screen in place for shipping.

These screws are located near top of screen.

Discard screws. Lift ﬁreplace screen up and

pull out to remove.

2. If logs are installed, carefully remove the logs

and set aside, noting the properly mounted

location of each.

www.desatech.com 111245-01B

3. Remove screws that attach ﬁreplace ﬂoor as-

sembly to ﬁreplace. Open lower louver door.

Carefully lift up ﬁreplace ﬂoor assembly and

remove from ﬁreplace, taking care to pull

ﬂexible gas line through the access holes (see

Figure 6). Note: Be careful of all wires on

underside of log base.

CAUTION: Do not pick up

ﬁreplace ﬂoor assembly by burn-

ers. This could damage burners.

Only handle base by grates.

INSTALLATION

Continued

Figure 6 - Removing Fireplace Floor

Assembly

Screws

Fireplace Floor

Assembly

Flexible Gas Line

ELECTRICAL CONNECTIONS FOR

POWER CORD

This fireplace operates on 120 VAC, 60 Hz

power. An electrical power cord is supplied with

this unit.

For Mantel Installation

1. Determine from which side of the ﬁreplace the

power cord will exit. Locate the 1.5" diameter

hole near the center of ﬂoor support bracket on

appropriate side of lower cavity (see Figure 7).

2. Locate power cord. Remove wire tie or tape

holding plug end of power cord.

3. Power cord has 2 plastic hole bushings

threaded onto it. Route cordʼs 3-prong plug

through the 1.5" diameter hole in appropriate

ﬂoor support bracket.

4. Push ﬁrst plastic bushing completely through

hole. Squeeze bushing as needed to do this.

5. Install the second plastic bushing into the

hole in the ﬂoor support bracket by snapping

into place.

6. Route the 3-prong plug through the 1.5" hole

in ﬁreplace outer casing.

7. Install the ﬁrst plastic bushing into this hole

by snapping into place.

8. After you have connected to gas supply and

checked your gas connections (see pages 17

through 20), plug power cord into any conve-

nient 3-prong grounded wall receptacle near

ﬁreplace.

For Recessed Installation

If an outlet is not installed in ﬁreplace, install

model GA3555 - Outlet Kit with Cover. This

kit will supply a convenient 3-prong grounded

electrical outlet for power. Refer to installation

manual provided with this optional accessory for

instructions on wiring. Note: A qualiﬁed installer

must make all electrical connections.

RELOCATING WALL SWITCH

ASSEMBLY

Note: The decorative wall switch plate supplied

is white. The wall switch plate may be painted to

match your decor.

The push-button switch and decorative wall

plate assembly supplied with your ﬁreplace is

pre-mounted at the factory in the lower cavity of

the ﬁreplace. You may relocate this wall switch

assembly to a more convenient location such as the

side of your mantel or directly onto the wall near

the ﬁreplace. To mount the wall switch assembly,

you must ﬁrst cut openings in the mantel or wall

where the switch will be located.

Figure 7 - Routing Power Cord

Power

Cord

Bushings

Hole in Floor

Support Bracket

Hole in Outer

Casing

Other manuals for CGEFP33PRB

This manual suits for next models

Table of contents

Other Desa Indoor Fireplace manuals

Desa

Desa C26GO Instruction manual

Desa

Desa W36TU Instruction manual

Desa

Desa Comfort Glow RFP28TC Quick start guide

Desa

Desa Comfort Glow CGCF26NR Quick start guide

Desa

Desa P325 Quick start guide

Desa

Desa EFS26PR Quick start guide

Desa

Desa VMH10TPB Quick start guide

Desa

Desa VTGF33NRA Quick start guide

Desa

Desa UNVENTED (VENT-FREE) NATURAL GAS FIREPLACE Operation manual

Desa

Desa VYGF33PRC Quick start guide

Desa

Desa VDCFTNB Quick start guide

Desa

Desa Vanguard VI33PR Quick start guide

Desa

Desa (V)KV36NE series Quick start guide

Desa

Desa Vanguard VSGF28NTE Quick start guide

Desa

Desa V42V-A Quick start guide

Desa

Desa VKC42N Series Quick start guide

Desa

Desa C36EMW User manual

Desa

Desa FLAME-MAX Vintage Oak Series Quick start guide

Desa

Desa C36 User manual

Desa

Desa VT32N Series Quick start guide

Desa

Desa (V)G36HR Safety guide

Desa

Desa S36 Series Quick start guide

Desa

Desa VYGF33NRB Quick start guide

Desa

Desa FPVF33PRA Quick start guide

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Miles Industries

Miles Industries Vogue 1300IRN Installation & operating instructions