Delta Tau PMAC User manual
5”Side View Complete Camera System
Owner’s manual
(VWIC500-SV)
Warranty Information
Thank you for purchasing a Vision Works camera system. We have taken great care to provide you with a top quality
product. Vision Works comes with a one year warranty that covers defective materials or workmanship, as long as no
wiring or parts are modified in any manner. If our product is found to be modified the warranty will be nullified.
Please read and follow the owner’s manual for installation and operation of your camera system.
Return Policy:
No merchandise should be returned to Vision Works for credit unless accompanied by a return authorization number from
our company. You will receive credit for the full amount of the return, if the merchandise is returned within 30 days of the
invoice date. Any merchandise that is not returned within 30 days of the invoice date is subject to a restocking fee of 15%.
Contact your Vision Works dealer for return information.
Merchandise that has been special ordered cannot be returned for credit. Non-stock items returned for credit will be
subject to vendor’s return policy.
Important!
1. To prevent short circuit, make sure that the system is not plugged in or receiving power while making system
connections. In the event of a system short circuit, replacement of the 3A fuse will be required. Fuses are
located under the threaded tip of the cigarette lighter, and inside the threaded barrel section of the RED 12volt
supply wire. Replacement fuses are not included with this kit.
2. To ensure that you do not drain your battery, it may be necessary to disconnect the cigarette adaptor when not
in use.
3. The camera is completely weatherproof but the monitor is NOT and should NOT be exposed to water. Please
ask about weatherproof monitors if you have no cab.
1
1.0 Specifications
Monitor Specifications Camera Specifications
Model
5”
Model
Sony
Screen Size
5 inch
Resolution
700 TVL
Aspect
Ratio
16:9
Lens
3.6 mm
Luminance
350cd/m2
No. of Pins
4
Resolution
400*R.G.B*272
Weatherproof
Rating
IP68
Audio &
Video
2 video/2 audio input (dual
channel, single image
display)
Low Temp
Rating
-20 C
-4 F
System
PAL & NTSC automatically
Magnet
Yes
Voltage
12V
Auto Shading
Yes
Language
Multi-language
OSD Menu
Display menu, brightness,
color, contrast adjustable
Bracket
Accessories
Self-Adhesive Base and
Suction Cup Base Included
Sunshade
Removable
2.0 Parts Identification
Monitor
Quantity 1
License Plate
Camera
Quantity 1
Main Harness
Quantity 1
2
Video Extension
Cable (30ft)
Quantity 1
Cigarette Lighter
Adapter
Quantity 1
AV Accessory Cable
Quantity 1
Self-Adhesive
Bracket
Quantity 1
Suction Cup
Bracket
Quantity 1
3
3.0 Assembly Instructions
4.1 Installation Instructions:
Camera can be mounted using magnet and
attaching hardware. These are the steps
required to attach the magnet to the camera.
1. Position and align center hole of camera
and bracket assembly on top of magnet.
2. Install bolt from underside of magnet and
secure with flat washer and nut. Tighten
this connection.
Tip: Although magnet contains 65lb pull force, it
we recommend mounting your camera on a flat
surface, and a zip tie be used in addition to
fasten the camera as a preventative measure in
the event the camera is knocked off.
Option 1: Self Adhesive Base Installation –
install monitor onto monitor base that contains
3M self-adhesive tape backing. Ensure the four
plastic tabs on base are locked into position on
rear of monitor. Ref. Fig.1. Adjust and position
monitor and base assembly to preferred viewing
location. Viewing surface location must be clean
and fairly smooth. Once desired position is
located, remove protective 3M tape backing from
monitor base, and position base to desired
location applying gentle pressure to monitor base
and mounting surface.
Option 2: Suction Cup Base Installation –
suction cup base installation is only
recommended for use on windows. Ensure the
four plastic tabs on base are locked into position
on rear of monitor. Ref. Fig.1. There is a quick
release on the base of the suction cup used to
attach and remove base from the window.
(Use Figure On Previous Page)
Connect MONITOR harness to the MAIN HARNESS MONITOR INPUT. Ensure arrows are aligned
on outer jacket of cable ends. Turn silver cable connector nut clockwise to secure connection of
the cables (IF YOU BEND THE PINS IT VOIDS THE WARRANTY). Ref. Picture Below & Fig.3
4
Connect VIDEO EXTENSION CABLE
harness to C1 input on MAIN HARNESS.
Ensure arrows are aligned on outer jacket of
cable ends.
Turn silver cable connector nut clockwise to
secure the connection of the cables.
Do not over tighten. Pull rubber sleeve
membrane over cable connection. Ref. Fig.2
Connect other end of VIDEO EXTENSION CABLE harness to CAMERA harness cable. Again, ensure arrows
are aligned on outer jacket of cable ends. Turn silver cable connector nut clockwise to secure the connection
of the cables. Do not overtighten.
Ref. Fig.2
Only one camera can be displayed at a time on monitor screen. The MAIN HARNESS included in this kit
contains two video cable inputs. The cable input labeled V2 can be used to accept a video signal from a
second optional camera. For V2 to activate and provide a video feed to the monitor, 12VDC power must be
supplied to the BLUE wire on the MAIN HARNESS. To change between both V1 and V2 video feeds, a switch
will need to be installed in the BLUE 12VDC wire. When the switch is activated to supply power to the BLUE
wire, the V2 video input will display on the monitor. When the switch is activated to terminate power to the
BLUE wire, the V1 video feed will display on the monitor.
Note: A common application for the V2 video feed is for rear view imaging when in reverse. For V2 video feed
for a reverse application, it is common to connect the BLUE wire to the reverse wire on the vehicle.
Ref. Fig.2
5
4.2 Power Cable Connection Installation:
5 Operating Instructions:
Increase (+) Setting –Increases the brightness/contrast of the screen with the menu button.
Menu –Provides menu options that then require adjustment with the increase and decrease setting.
Decrease (-) Setting –Decreases the brightness/contrast of the screen with the menu button.
Cigarette Lighter Adapter - system can be powered by connecting the MAIN HARNESS CIGARETTE
LIGHTER INPUT to the mating connector of the CIGARETTE LIGHTER ADAPTER. The cigarette lighter
adapter can now be installed into a 12VDC power source. To verify that the system is receiving power, cup
your hands over the camera lens, and the LED lights will have a red glow. Ref. Fig.2
Hardwire Option: - Connect BLACK wire of MAIN HARNESS to ground. Connect RED wire of MAIN
HARNESS to 12VDC power supply. To verify that the system is receiving power, cup your hands over the
camera lens, and the LED lights will have a red glow. DO NOT USE THE BLUE WIRE (only use when you
have two cameras).
Ref. Fig.2
Other manuals for PMAC
2
Table of contents
Other Delta Tau Controllers manuals
Delta Tau
Delta Tau PMAC PC User manual
Delta Tau
Delta Tau Turbo PMAC PCI-Lite Quick user guide
Delta Tau
Delta Tau Power PMAC Clipper User manual
Delta Tau
Delta Tau 5XX-603869-XUXX User manual
Delta Tau
Delta Tau PBC Series Operating and maintenance manual
Delta Tau
Delta Tau PMAC2-PC Quick user guide
Delta Tau
Delta Tau PMAC2A-PC/104 Quick user guide
Delta Tau
Delta Tau PMAC 1.5 Lite Quick user guide
Delta Tau
Delta Tau ACC-11E User manual
Delta Tau
Delta Tau PMAC2-PC Quick user guide
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
