Dell Storage Center SCv2000 User manual
Dell Storage Center
SCv2000 and SCv2020 Storage System
Getting Started Guide
Regulatory Model: E09J, E10J
Regulatory Type: E09J001, E10J001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make
better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or
loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright ©2016 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other
trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
trademarks of their respective owners.
2016 - 12
Rev. A00
Setting Up the Storage System
Consider the following best practices when setting up an SCv2000/SCv2020
storage system.
• Dell recommends that you use a dedicated SAN network for data transmission
when using a Fibre Channel or iSCSI storage system.
• Complete the Worksheet to Record System Information in this guide before
configuring the storage system.
• Always configure redundant data paths to provide alternate paths to and from
the host server should one of the data paths become disabled.
• Before connecting any cables between the storage system and host server or
expansion enclosure, physically label each port and connector.
• Always follow proper power-up and power-down procedures when cycling power
across the network. Verify that critical network components are on separate
power circuits.
NOTE: This product is intended for restricted access locations, such as a
dedicated equipment room or equipment closet.
WARNING: If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room
ambient temperature. Therefore, consideration should be given to installing
the equipment in an environment compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
Safety Warnings
Battery pack warning
Remove the battery pack before removing a storage
controller from the storage system.
3
WARNING: Installing an incompatible battery may increase the risk of fire or
explosion. Observe the following precautions:
• The battery should only be replaced with a battery that is the same or
equivalent as the factory installed battery.
• Do not attempt to open or service the battery. Do not dispose of the
battery in a fire or with household waste. Contact the local waste disposal
agency for the location of the nearest battery deposit site.
Laser Radiation for Fibre Channel Storage Systems
CAUTION: Class I laser radiation when open, avoid exposure
to beam.
WARNING: Laser radiation, avoid direct exposure to beam.
The unit is certified in the U.S. to conform to the requirements of DHHS 21 CFR,
chapter 1 Subchapter J for Class I (1) laser products, and elsewhere is certified as a
Class I laser product conforming to the requirements of IEC 60825-1:2007.
Class I laser products are not considered to be hazardous. The laser system and unit
are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance or prescribed service condition.
4
Worksheet to Record System Information
Use the following worksheet to record the information that is needed to install the
SCv2000/SCv2020 storage system.
Storage Center Information
Gather and record the following information about the Storage Center network and
the administrator user.
Table 1. Storage Center Network
Service Tag ________________
Management IPv4 address (Storage Center management
address)
___ . ___ . ___ . ___
Top Controller IPv4 address (Controller 1 MGMT port) ___ . ___ . ___ . ___
Bottom Controller IPv4 address (Controller 2 MGMT
port)
___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
Domain name ________________
DNS server address ___ . ___ . ___ . ___
Secondary DNS server address ___ . ___ . ___ . ___
Table 2. Storage Center Administrator
Password for the default Storage Center “Admin” user ________________
Email address of the default Storage Center “Admin” user ________________
5
iSCSI Fault Domain Information
For a storage system with iSCSI front-end ports, gather and record network
information for the iSCSI fault domains. This information is needed to complete the
Discover and Configure Uninitialized SCv2000 Series Storage Centers wizard.
NOTE: For a storage system deployed with two Ethernet switches, Dell
recommends setting up each fault domain on separate subnets.
See the Dell Storage Center SCv2000/SCv2020 Storage System Deployment Guide
for information about setting up iSCSI fault domains.
Table 3. iSCSI Fault Domain 1
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 1 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 1 ___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage
controller module 1: port 3
___ . ___ . ___ . ___
(Four port I/O card only) IPv4 address for storage
controller module 2: port 3
___ . ___ . ___ . ___
Table 4. iSCSI Fault Domain 2
Target IPv4 address ___ . ___ . ___ . ___
Subnet mask ___ . ___ . ___ . ___
Gateway IPv4 address ___ . ___ . ___ . ___
IPv4 address for storage controller module 1: port 2 ___ . ___ . ___ . ___
IPv4 address for storage controller module 2: port 2 ___ . ___ . ___ . ___
(4-port I/O card only) IPv4 address for storage controller
module 1: port 4
___ . ___ . ___ . ___
6
(4-port I/O card only) IPv4 address for storage controller
module 2: port 4
___ . ___ . ___ . ___
Additional Storage Center Information
The Network Time Protocol (NTP) and Simple Mail Transfer Protocol (SMTP) server
information is optional. The proxy server information is also optional, but it may be
required to complete the Discover and Configure Uninitialized SCv2000 Series
Storage Centers wizard.
Table 5. NTP, SMTP, and Proxy Servers
NTP server IPv4 address ___ . ___ . ___ . ___
SMTP server IPv4 address ___ . ___ . ___ . ___
Backup SMTP server IPv4
address
___ . ___ . ___ . ___
SMTP server login ID ________________
SMTP server password ________________
Proxy server IPv4 address ___ . ___ . ___ . ___
Fibre Channel Zoning Information
For a storage system with Fibre Channel front-end ports, record the physical and
virtual WWNs of the Fibre Channel ports in Fault Domain 1 and Fault Domain 2. This
information is displayed on the Review Front-End page of the Discover and
Configure Uninitialized SCv2000 Series Storage Centers wizard. Use this
information to configure zoning on each Fibre Channel switch.
See the Dell Storage Center SCv2000/SCv2020 Storage System Deployment Guide
for information about setting up Fibre Channel zoning.
Table 6. Physical WWNs in Fault Domain 1
Physical WWN of storage controller 1: port 1 ________________
Physical WWN of storage controller 2: port 1 ________________
7
(4-port I/O card only) Physical WWN of storage controller
1: port 3
________________
(4-port I/O card only) Physical WWN of storage controller
2: port 3
________________
Table 7. Virtual WWNs in Fault Domain 1
Virtual WWN of storage controller 1: port 1 ________________
Virtual WWN of storage controller 2: port 1 ________________
(4-port I/O card only) Virtual WWN of storage controller
1: port 3
________________
(4-port I/O card only) Virtual WWN of storage controller
2: port 3
________________
Table 8. Physical WWNs in Fault Domain 2
Physical WWN of storage controller 1: port 2 ________________
Physical WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Physical WWN of storage
controller 1: port 4
________________
(4-port I/O card only) Physical WWN of storage
controller 2: port 4
________________
Table 9. Virtual WWNs in Fault Domain 2
Virtual WWN of storage controller 1: port 2 ________________
Virtual WWN of storage controller 2: port 2 ________________
(4-port I/O card only) Virtual WWN of storage controller
1: port 4
________________
(4-port I/O card only) Virtual WWN of storage controller
2: port 4
________________
8
Locating Your Service Tag
Your storage system is identified by a unique service tag and Express Service Code.
You can find the service tag and Express Service Code on the service luggage tag
located next to the front panel display. Alternatively, the information may be on a
sticker on the back of the storage system chassis. Dell uses this information to route
support calls to the appropriate personnel.
Figure 1. Service Tag Locations
1. Service luggage tag 2. Service tag label
Other Information You May Need
To install the storage system, you may need the following additional information.
NOTE: See the safety and regulatory information that shipped with your
Storage Center components. Warranty information is included as a separate
document.
• The Dell Storage Center SCv2000/SCv2020 Storage System Deployment Guide
provides information about cabling storage system hardware components and
configuring a new storage system using the Dell Storage Manager Client.
• The Dell Storage Manager Storage Center Administrator's Guide describes how
to use the Dell Storage Manager Client to manage a Storage Center.
• The Dell Storage Manager Administrator’s Guide describes how to use Dell
Storage Manager to manage multiple Storage Center systems.
9
Installation and Configuration
Before you begin installation, make sure that the site where you plan to install the
storage system has standard power from an independent source or a rack power
distribution unit with a UPS.
In addition, verify that there is space in the rack to install the storage system.
Unpacking Storage Center Equipment
Unpack the storage system and identify the items in your shipment.
Figure 2. SCv2000/SCv2020 Storage System Components
1. Documentation 2. Storage system
3. Rack rails (2) 4. Front bezel
Installing the Storage System in a Rack
Install the SCv2000/SCv2020 storage system and other Storage Center system
components in a rack.
NOTE: Mount the storage system in a manner that allows for expansion in
the rack and prevents the rack from becoming top‐heavy.
1. Secure the rails that are pre-attached to both sides of the storage system
chassis.
10
Other manuals for Storage Center SCv2000
3
This manual suits for next models
1
Table of contents
Other Dell Storage manuals
Dell
Dell PowerVault 500 Series User manual
Dell
Dell PowerVault DR4100 User manual
Dell
Dell PowerVault LTO3-080 User manual
Dell
Dell EMC AX4-5I Manual
Dell
Dell PowerVault CX193 User manual
Dell
Dell PowerVault 136T Installation and operation manual
Dell
Dell EMC VxFlex Ready Node R840 User manual
Dell
Dell PS6500 Assembly Instructions
Dell
Dell Wyse C Class User manual
Dell
Dell PowerVault 132T LTO User manual
Dell
Dell PowerVault 136T Owner's manual
Dell
Dell PowerVault NX300 User manual
Dell
Dell PowerVault NX1950 Guide
Dell
Dell SC7020 User manual
Dell
Dell PowerVault 200S Quick guide
Dell
Dell Storage Center SC220 User manual
Dell
Dell PowerVault MD3860i Series User manual
Dell
Dell SC180 User manual
Dell
Dell PowerVault DL2100 User manual
Dell
Dell PowerVault 701N Technical manual
