Dell PowerEdge C6220 II User manual
Dell PowerEdge
C6220 II
Getting Started
With Your System
Mise en routedusystème
Introdução ao usodosistema
Pasos inicialespara susistema
Dell PowerEdge
C6220 II
Getting Started
With Your System
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of
your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of
data if instructions are notfollowed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
______________
Informationin this document is subject to change without notice.
© 2013 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is st rictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of
Dell Inc. Intel® and Intel® Xeon® are registered trademarks of Intel Corporation in the
U.S. and other countries. Red Hat Enterprise Linux® and Enterprise Linux® are
registered trademarks of Red Hat, Inc. in the United States and/or other countries.
Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United
States and other countries. Citrix® and XenServer® are either registered trademarks or
trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®
is a registered trademarks or trademarks of VMWare, Inc. in the United States or other
countries.
Other trademarks and trade names may be used in this publication to refer to either the
entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
RegulatoryModel B08S
May2013 P/N 1PFTR Rev. A00
Getting Started With YourSystem | 3
CAUTION: Restricted Access Location
This server is intended for installation only in restricted access locations as
defined in Cl. 1.2.7.3 of I EC 60950-1: 2001 where both these conditions apply:
•Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
•Access is through the use of a tool or lock and key, or ot her means of
security, and is controlled by the authority responsible for the location.
Installation and Configuration
WARNING: Before performing the following procedure, review and follow the
safety instructions that came with the system.
Installing the Tool-Less Rail Solution
WARNING: Wheneveryou
needtoliftthe system, get others toassist you.
To avoid injury, do not attempt to liftthe system by yourself.
WARNING: The system is not fixedtothe rack ormounted onthe rails. To
avoid personal injury or damage to the system, you must adequately
support the system during installation and removal.
WARNING: Toavoida potentialelectrical shock hazard,a thirdwire safety
grounding conductor is necessary for the rack installation. The rack
equipment must provide sufficient airflow to the system to maintain proper
cooling.
CAUTION: When installing rails in a square-hole rack it is important to
ensure that the square peg slides through the square holes.
Getting Started With YourSystem | 4
1 Push on the latch release buttons on the midpoints of t he end piece t o
open the rail latches. See Figure 1.
2 Align the end pieces of the rails on the vertical rack flanges to seat
the pegs in the bottom hole of the first U and the top hole of the
second U.
NOTE: The rails can be used in both square-hole (item 1 in the following figure)
and round-hole racks (item 2 in the following figure).
Figure 1. Pushing the Latch Release Buttons
NOTE: To remove the rails, push on the latch release button on the midpoints
of the end piece and unseat each rail.
Getting Started With YourSystem | 5
3 Engage the end of the rails and release the latch release button to
have the latches locked in place. See Figure 2.
Figure 2. Releasing the Latch Release Buttons
Getting Started With YourSystem | 6
4 On each vertical rack flange on the back, put two screw bases into
the two square holes right above the rail. See Figure 3.
5 Inst all the chassis stabilizer shipping brackets (optional) on the back
rack flanges.
6 Inst all and tight en the s crews.
NOTE: To transport systems already installed in the rack, ensure that the two
chassis stabilizer shipping brackets (optional) are in place.
Figure 3. Installing the Chassis Stabilizer Shipping Brackets
Getting Started With YourSystem | 7
7 Slide the system into the rack. See Figure 4.
8 Tighten the thumbscrews to secure the ears of the system to the front
of t he rack flanges.
Figure 4. Installing the Chassis onto the Rack.
Getting Started With YourSystem | 8
Optional—Connecting theKeyboard,Mouse, and Monitor
Figure 5. Optional—Connecting the Keyboard, Mouse and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable to
plug into each connector. Be sure to tight en the screws (if any) on the monitor’s
cable connector.
Other manuals for PowerEdge C6220 II
5
Table of contents
Languages:
Other Dell Server manuals
Dell
Dell PowerEdge C5125 User manual
Dell
Dell POWEREDGE R515 User manual
Dell
Dell PowerEdge 6600 User manual
Dell
Dell VxRail P670F Manual
Dell
Dell PowerEdge R320 User manual
Dell
Dell PowerEdge 860 User manual
Dell
Dell EMC PowerEdge R6525 Manual
Dell
Dell PowerEdge M820 Systems User manual
Dell
Dell PowerEdge 2800 Manual
Dell
Dell EMC PowerEdge T340 Manual
Dell
Dell PowerVault NX3500 Service manual
Dell
Dell EMC PowerEdge E45S Series Manual
Dell
Dell PowerEdge 1850 Installation and operation manual
Dell
Dell EMC ScaleIO Ready Node 14G User manual
Dell
Dell External OEMR XL R210II Quick start guide
Dell
Dell PowerEdge 2800 Manual
Dell
Dell PowerEdge R420 Owner's manual
Dell
Dell EMC PowerEdge R640 Manual
Dell
Dell EMC ScaleIO Ready Node 14G Installation instructions
Dell
Dell HHB006 Manual
