Dell PowerEdge C5125 User manual
Dell PowerEdge C5125
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Dell PowerEdge C5125
Getting Started
With Your System
Regulatory Model: B04S
Notes, Cautions, and Warnings
____________________
Information in this publication is subject to change without notice.
© 2011 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™are trademarks of Dell Inc.
AMD®, AMD Phenom™, and AMD Athlon™are trademarks of Advanced Micro Devices, Inc.
Microsoft®and Windows®are either trademarks or registered trademarks of Microsoft Corporation
in the United States and/or other countries. Red Hat®and Red Hat Enterprise Linux®are registered
trademarks of Red Hat, Inc. in the United States and/or other countries. SUSE™ is a trademark of
Novell Inc. in the United States and other countries. Citrix®, Xen®, and XenServer®are either
registered trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries.
VMware®is a registered trademarks or trademarks of VMWare, Inc. in the United States or other
countries.
Other trademarks and trade names may be used in this publication to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
Regulatory Model B04S
March 2011 P/N 00XMM Rev. A00
NOTE: A note indicates important information that will help a user make better use
of a computer system.
CAUTION: A caution indicates potential damage to hardware or loss of data is
instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
Installation and Configuration 3
This server is intended for installation only in restricted access locations as
defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions
apply:
• Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
• Access is through the use of a tool or lock and key, or other means of
security, and is controlled by the authority responsible for the location.
Installation and Configuration
Unpacking the System
Unpack your system and identify each item.
Installing the Tool-Less Rail Solution
CAUTION: Restricted Access Location
WARNING: Before performing the following procedure, review and follow the
safety instructions that came with the system.
WARNING: Whenever you need to lift the system, get others to assist you.
To avoid injury, do not attempt to lift the system by yourself.
WARNING: The system is not fixed to the rack or mounted on the rails. To avoid
personal injury or damage to the system, you must adequately support the system
during installation and removal.
WARNING: To avoid a potential electrical shock hazard, a third wire safety
grounding conductor is necessary for the rack installation. The rack equipment
must provide sufficient airflow to the system to maintain proper cooling.
CAUTION: When installing rails in a square-hole rack it is important to ensure
that the square peg slides through the square holes.
CAUTION: Square studs must be flush with the rack posts to install properly.
4Installation and Configuration
1
Pull on the latch release buttons on the end piece midpoints to open the
rail latches.
2
Align the end pieces of the rails on the vertical rack flanges to seat the pegs
in the bottom hole of the first U and the top hole of the second U. Engage
the back end of the rail until the latch locks in place.
NOTE: The rails can be used in both square-hole and round-hole racks.
Front
Back
Installation and Configuration 5
3
Insert the cage nut on the rack.
4
Repeat steps 1 to 4 to position and seat the front end piece on the vertical
flange.
NOTE: To remove the rails, pull on the latch release button on the end piece
midpoint and unseat each rail.
6Installation and Configuration
Installing the System
Empty the System Chassis
1
Unplug the power cable from the power supply unit.
.
2
Pull out the power supply unit handle.
Installation and Configuration 7
3
Press down on the release latch
.
4
Pull the power supply unit out of the system
.
5
Press the release latch down
and pull the sled out of the system
.
8Installation and Configuration
Install the System Into the Rack
1
Slide the system into the rack.
2
If present, remove the chassis stabilizer shipping bracket (optional) from
the rack.
3
Tighten the captive thumbscrews to secure the ears of the system to the
front of the rack.
4
Install the stopping bracket on the post and secure with M5 screws.
WARNING: Whenever you need to lift the system, get others to assist you.
To avoid injury, do not attempt to lift the system by yourself.
NOTE: To transport systems already installed in the rack, ensure that the two
chassis stabilizer shipping brackets (optional) are in place.
NOTE: Make sure the latch release mechanism is engaged correctly.
Other manuals for PowerEdge C5125
4
Table of contents
Languages:
Other Dell Server manuals
Dell
Dell EMC PowerEdge T350 3RRTM Manual
Dell
Dell PowerEdge C410X User manual
Dell
Dell PowerEdge 1655MC User manual
Dell
Dell OptiPlex FX170 User manual
Dell
Dell PowerEdge 1800 Manual
Dell
Dell DSS 1510 User manual
Dell
Dell PowerEdge 2970 Technical manual
Dell
Dell Precision Workstation 350 Technical manual
Dell
Dell PowerEdge 7250 Quick start guide
Dell
Dell DX6000G User manual
Dell
Dell POWEREDGE T300 User manual
Dell
Dell E14S Series User manual
Dell
Dell POWEREDGE 1900 Technical manual
Dell
Dell PowerEdge 1650 User manual
Dell
Dell PowerEdge R415 User manual
Dell
Dell PowerEdge R360 Manual
Dell
Dell PowerEdge 1750 User manual
Dell
Dell External OEMR XL R720XD Quick start guide
Dell
Dell PowerEdge SC1420 User manual
Dell
Dell EMC PowerEdge T340 Manual
