Dell PowerEdge 6400 User manual

ZZZGHOOFRP

VXSSRUWGHOOFRP

'HOO3RZHU(GJH[DQG[6\VWHPV

6&6,%$&.3/$1(237,21

73JXGbk2.book Page 3 Wednesday, May 17, 2000 4:49 PM

1RWHV1RWLFHV&DXWLRQVDQG:DUQLQJV

Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of

your computer system.

127,&($127,&(LQGLFDWHVHLWKHUSRWHQWLDOGDPDJHWRKDUGZDUHRUORVV

RIGDWDDQGWHOOV\RXKRZWRDYRLGWKHSUREOHP

&$ 7,21$&$ 7,21LQGLFDWHVDSRWHQWLDOO\KD]DUGRXVVLWXDWLRQZKLFKLI

QRWDYRLGHGPD\UHVXOWLQPLQRURUPRGHUDWHLQMXU\

:$51,1*$:$51,1*LQGLFDWHVDSRWHQWLDOO\KD]DUGRXVVLWXDWLRQZKLFK

LIQRWDYRLGHGFRXOGUHVXOWLQGHDWKRUVHULRXVERGLO\LQMXU\

____________________

Information in this document is subject to change without notice.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Computer

Corporation. Other trademarks and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Dell Computer Corporation disclaims

any proprietary interest in trademarks and trade names other than its own.

May 2000 P/N 73JXG Rev. A02

73JXGbk2.book Page 4 Wednesday, May 17, 2000 4:49 PM

support.dell.com SCSI Backplane Option 1

'HOO3RZHU(GJH[DQG

[6\VWHPV6&6, DFNSODQH

2SWLRQ

This document describes the installation procedure for the optional small computer

system interface (SCSI) backplanes for the Dell PowerEdge 4x00 and 6x00 systems.

,QVWDOOLQJD6&6, DFNSODQH RDUG

To replace your computer’s SCSI backplane board with a different backplane board,

perform the following steps.

&$ 7,217RSUHYHQWERGLO\LQMXU\EHIRUHSURFHHGLQJ\RXPXVWWXUQRII

WKHFRPSXWHUDQGGLVFRQQHFWLWIURPLWV$&SRZHUVRXUFH)RUPRUHLQIRU

PDWLRQVHH´6DIHW\)LUVW³)RU<RXDQG<RXU&RPSXWHUµLQ\RXUV\VWHP·V

8VHU·V*XLGH

1. Turn off the system, including any attached peripherals, and disconnect the sys-

tem from the electrical outlet.

127,&(7RSUHYHQWGDPDJHWRWKH6&6,EDFNSODQHDQGFRPSXWHUV\VWHP

GXULQJWKLVSURFHGXUHVHH´3URWHFWLQJ$JDLQVW(OHFWURVWDWLF'LVFKDUJHµLQ

\RXUV\VWHP·V8VHU·V*XLGH

2. Unpack the SCSI backplane board upgrade kit.

3. Remove the computer cover and front bezel.

127,&(<RXPXVWUHPRYHDOOKDUGGLVNGULYHVWRDYRLGGDPDJLQJWKH6&6,

EDFNSODQHERDUGZKHQ\RXUHPRYHLWODWHULQWKLVSURFHGXUH

4. Remove the hard-disk drives from the system.

5. Slide the system board tray to its service position.

6. Disconnect the SCSI cable from the SCSI backplane board.

To avoid damage to the cable, use the strain-relief loop to disconnect the cable.

73JXGbk2.book Page 1 Wednesday, May 17, 2000 4:49 PM

2 SCSI Backplane Option

7. Disconnect the flat data cable from the locking connector on the backplane

board.

8. Disconnect the power cable labeled "HD-B/P" from the power connector on the

backplane board.

To release the connector, press the latch on the side of the connector.

9. Disconnect the fan power cable from the power connector labeled "FAN" on the

backplane board.

To release the connector, press the latch on the side of the connector.

10. Loosen the captive thumbscrew on the backplane board.

11. Slide the SCSI backplane board away from the chassis inner wall approximately

1 centimeter (cm) (a quarter inch), and then lift the board off of the L-shaped

mounting tabs and away from the chassis (see Figure 1).

)LJXUH5HPRYLQJD6&6, DFNSODQH RDUG

1Thumbscrew

2SCSI backplane board

73JXGbk2.book Page 2 Wednesday, May 17, 2000 4:49 PM

support.dell.com SCSI Backplane Option 3

12. Install the new backplane board:

a. While holding the backplane board by its edges, position the board so that

the tabs on the computer chassis wall fit through the corresponding slots in

the backplane board.

b. Slide the backplane board toward the power supply paralleling board.

c. Secure the backplane board by tightening the captive thumbscrew.

d. Connect the 20-pin data cable from the system board to the connector

labeled "PLANAR" on the backplane board (see Figure 2 or Figure 3).

)LJXUH DFNRI[RU[6&6, DFNSODQH RDUG

1Cooling fan power cable connector (FAN)

2Power connector (POWER)

3System-board data cable connector (PLANAR)

4Ultra3 SCSI cable connector (SCSIA)

73JXGbk2.book Page 3 Wednesday, May 17, 2000 4:49 PM

4 SCSI Backplane Option

)LJXUH DFNRI[6&6, DFNSODQH RDUG

13. Connect the power cable labeled "HD-B/P" to the connector labeled "POWER" on

the backplane board.

14. Connect a SCSI cable from the connector labeled "SCSIA" on the backplane board

to the connector labeled “PRIMARY SCSIA”on the system board, or to a SCSI

host adapter card.

15. If you want to operate the backplane in a split 2 x 4 configuration, connect a SCSI

cable from the connector labeled "SCSIB" on the backplane board to the second

Ultra3 SCSI connector on the system board, or to a SCSI host adapter card.

NOTES: When the 2 x 4 SCSI backplane is cabled to two SCSI host adapter

cards, the SCSI host adapter cabled to the 2 x 4 backplane’s SCSIA connector will

control the four top hard-disk drives of a rack-mounted system (or the four left-

most hard-disk drives of an upright free-standing system) with SCSI IDs 0, 1, 2,

and 3; and will control the four bottom hard-disk drives of a rack-mounted system

(or the four rightmost hard-disk drives of an upright free-standing system) with

SCSI IDs 4, 5, 8, and 9.

1Ultra3 SCSI cable connector (SCSIA)

2Ultra3 SCSI cable connector (SCSIB)

3Cooling fan power cable connector (FAN)

4Power connector (POWER)

5System-board data cable connector (PLANAR)

73JXGbk2.book Page 4 Wednesday, May 17, 2000 4:49 PM

support.dell.com SCSI Backplane Option 5

You can configure the 2 x 4 SCSI backplane as a 1 x 8 backplane by connecting

only the connector labeled "SCSIA" on the backplane board to a SCSI controller.

16. Slide the system board tray back into the system chassis.

Does the new SCSI backplane board have a different number of drive bays?

Ye s .You must change the orientation of the two drive bay keys to match the new

backplane. Go to step 17.

No.Go to step 23.

17. Turn the key in the keylock to lock the drive-locking flange (see Figure 4).

With the flange in the locked position, you have easier access to the upper drive

bay key.

)LJXUH5HPRYLQJWKH'ULYH D\.H\V

1Screws (6)

2Drive-locking flange

73JXGbk2.book Page 5 Wednesday, May 17, 2000 4:49 PM

6 SCSI Backplane Option

18. To remove the upper drive bay key, remove the three screws.

19. To remove the lower drive key, remove the three screws securing the key to the

chassis.

20. Rotate each drive bay key so that the "6" or "8" stamped on the end of each key

faces forward and matches the drive capacity of the new backplane (see

Figure 5).

)LJXUH5HLQVWDOOLQJWKH'ULYH D\.H\V

21. Reinstall the lower drive key using the three screws.

22. To reinstall the upper drive key, lock the drive-locking flange and reinstall the three

screws through the flange cutouts.

1Key stamp

2Lower drive bay key

3Upper drive bay key

73JXGbk2.book Page 6 Wednesday, May 17, 2000 4:49 PM

support.dell.com SCSI Backplane Option 7

23. Replace the front bezel and computer cover.

24. Reinstall the hard-disk drives in the computer.

NOTE: You can use only 1-inch hard-disk drives with an 8-bay backplane—you cannot

use 1.6-inch hard-disk drives. (A 6-bay backplane can accommodate 1.6-inch or 1-inch

drives.) If you install an 8-bay backplane, you need to convert the drive carriers to the

1-inch width by removing the spacer insert that fastens to each carrier adjacent to the

carrier release handle.

25. Reconnect the computer and peripherals to their AC power sources.

73JXGbk2.book Page 7 Wednesday, May 17, 2000 4:49 PM

8 SCSI Backplane Option

73JXGbk2.book Page 8 Wednesday, May 17, 2000 4:49 PM

Other manuals for PowerEdge 6400

Other Dell Server manuals

Dell

Dell Force10 S2410-01-10GE-24P Installation manual

Dell

Dell PowerEdge 2850 User manual

Dell

Dell PowerEdge 800 Technical manual

Dell

Dell PowerEdge R630 User manual

Dell

Dell PowerEdge C4130 User manual

Dell

Dell EMC PowerEdge R640 Manual

Dell

Dell PowerEdge 860 Technical manual

Dell

Dell PowerEdge R910 Technical manual

Dell

Dell ECS EX Series Installation instructions

Dell

Dell PowerEdge 2850 Technical manual

Dell

Dell EMC PowerEdge XE8545 User manual

Dell

Dell PowerEdge FX2 User manual

Dell

Dell PowerEdge 6600 Operation and maintenance manual

Dell

Dell PowerEdge R630 User manual

Dell

Dell POWEREDGE 1900 User manual

Dell

Dell PowerEdge C8000 User manual

Dell

Dell PowerEdge SC430 Owner's manual

Dell

Dell PowerEdge T105 Systems General instructions

Dell

Dell PowerEdge C6220 II User manual

Dell

Dell PowerEdge 2650 User manual

Dell

Dell PowerEdge 6400 User manual

Dell

Dell POWEREDGE R515 User manual

Dell

Dell Active Fabric Manager User manual

Dell

Dell PowerEdge M620 Quick start guide

Popular Server manuals by other brands

HP AlphaServer ES47 Cli reference manual

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

EtroVISION

EtroVISION EV3151 user manual

NEC

NEC Express5800/T110j System configuration guide

HP ProLiant Gen9 user guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

HP Integrity rx2600 overview

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual

Lenovo

Lenovo ThinkSystem SR635 V3 user guide

Fujitsu

Fujitsu PRIMERGY BX900 quick start guide

Asus

Asus RS700DA-E6 PS4 user manual