Dell PowerEdge 2800 Manual
www.dell.com | support.dell.com
Dell™ Systems
Installing the SCSI Backplane
Daughter Card
安装 SCSI 背板子卡
Installation de la carte fille
de fond de panier SCSI
Installieren der SCSI-Rückwandplatinen-
Tochterkarte
SCSI バックプレーンドータ
カードの取り付け
SCSI 후면판 보조 카드 설치
Instalación de la tarjeta secundaria
de plano posterior SCSI
www.dell.com | support.dell.com
Dell™ Systems
Installing the SCSI Backplane
Daughter Card
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2004 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
July 2004 P/N F6589 Rev. A00
Installing the SCSI Backplane Daughter Card 1-3
This document provides information about how to configure the split SCSI backplane in your
Dell™ PowerEdge™ 2800 or 2850 system by installing a backplane daughter card. In a split
backplane configuration, the hard-drives are arranged in two separate groups of drives.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any
of the components inside the system. See your Product Information Guide for complete information
about safety precautions, working inside the computer, and protecting against electrostatic discharge.
NOTE: See your Installation and Troubleshooting Guide for detailed instructions on removing
or replacing components.
Installing the SCSI Backplane Daughter Card
in a PowerEdge 2800 System
1
Remove the bezel (if applicable).
2
Unpack the SCSI backplane daughter card kit.
3
Turn off the system, including any attached peripherals, and disconnect the system from
the electrical outlet.
4
Open the system.
5
Slide the drive tray to the maintenance position.
a
Use a #2 Phillips screwdriver to loosen the captive screw that secures the drive tray
release handle to the chassis.
b
Rotate the drive tray release lever toward the front of the system.
c
Grasp both sides of the front panel and slide the drive tray forwards until the tray is in
the maintenance position.
6
Hold the daughter card by its edges with the card connector facing the SCSI backplane board.
7
Insert the card connector into the daughter card connector on the SCSI backplane board.
Ensure that the standoffs on the daughter card are fully seated into the SCSI backplane
board. See Figure 1-1.
1-4 Installing the SCSI Backplane Daughter Card
www.dell.com | support.dell.com
Figure 1-1. Installing the SCSI Daughter Card
8
To use the optional integrated ROMB controller in a split 2 x 4 backplane configuration:
a
Connect channel A on the riser card to SCSIA on the SCSI backplane. This channel
controls the boot drive (drive 0) and drives 1, 2, and 3.
b
Connect SCSI channel B on the riser card to connector SCSIB on the SCSI backplane.
This channel controls drives 4, 5, 8, and 9.
To use an optional RAID controller card in a split 2 x 4 backplane configuration:
a
Connect SCSI channel A (channel 0) on the controller card to connector SCSIA on
the SCSI backplane. This channel controls the boot drive (drive 0) and drives 1, 2, and 3.
b
Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on
the SCSI backplane. This channel controls drives 4, 5, 8, and 9.
9
Slide the drive tray back into the operating position.
a
Grasp both sides of the front panel and slide the drive tray backwards until the tray is
in the operating position.
b
Rotate the drive tray release lever toward the back of the system.
c
Use a #2 Phillips screwdriver to tighten the captive screw that secures the drive tray
release handle to the chassis.
10
Close the system.
11
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
12
Enter System Setup to ensure that the RAID or SCSI controller card is configured correctly.
See your system’s
User’s Guide
for more information.
13
Replace the bezel (if applicable).
SCSI daughter card
SCSI backplane board
standoffs (2)
Installing the SCSI Backplane Daughter Card 1-5
Installing the SCSI Backplane Daughter Card
in a PowerEdge 2850 System
1
Unpack the SCSI backplane board daughter card kit.
2
Turn off the system, including any attached peripherals, and disconnect the system from
the electrical outlet.
3
Remove the bezel (if applicable).
4
Open the system.
5
Grasp the plastic tab on the back of the control panel cable and pull the cable connector away
from the backplane connector. See Figure 1-2.
NOTE: If you pull on the control panel cable harness, you may damage the harness.
The SCSI backplane daughter card connector and card guide are located in the compartment
below the control panel cable.
Figure 1-2. Installing a SCSI Backplane Daughter Card
SCSI daughter card
SCSI backplane
retention lever
SCSI daughter card guide
retention peg
on card
control panel cable
SCSI daughter card
backplane connector
control-panel connector on backplane
1-6 Installing the SCSI Backplane Daughter Card
www.dell.com | support.dell.com
6
The daughter card fits between the sides of the card guide. To install the daughter card in
the card guide and to connect it to the backplane connector:
a
Ensure that the retention lever is in the open position.
b
Hold the daughter card by its edges with the card connector facing the SCSI backplane
and the retention peg facing the retention lever. See Figure 1-2.
c
Lower the card into the card guide.
d
Close the retention lever to slide the daughter card into the SCSI backplane connector
and lock the card into place. See Figure 1-2.
7
Rotate the drive bay retraction bar toward the front of the system. See Figure 1-3.
Figure 1-3. Drive Bay Retraction Bar
8
Reconnect the control panel cable to its backplane connector. See Figure 1-2.
9
To use the optional integrated ROMB controller in a split backplane configuration:
a
Connect channel A on the riser card to SCSIA on the SCSI backplane. This channel
controls the boot drive (drive 0) and drive 1.
b
Connect SCSI channel B on the riser card to connector SCSIB on the SCSI backplane.
This channel controls drives 2 through 5.
drive bay retraction bar
Installing the SCSI Backplane Daughter Card 1-7
To use the optional RAID controller card in a split backplane configuration:
a
Connect SCSI channel A (channel 0) on the controller card to connector SCSIA on
the SCSI backplane. This channel controls the boot drive (drive 0) and drive 1.
b
Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on
the SCSI backplane. This channel controls drives 2 through 5.
NOTE: If a cable is connected to the SCSIB backplane connector, the SCSI backplane daughter
card must be installed to activate the 2/4 split backplane configuration. Otherwise, the system will
display an error message.
10
Rotate the drive bay retraction bar toward the back of the system.
11
Close the system.
12
Enter System Setup to ensure that the RAID or SCSI controller card is configured correctly.
See your system’s
User’s Guide
for more information.
13
Replace the bezel (if applicable).
1-8 Installing the SCSI Backplane Daughter Card
www.dell.com | support.dell.com
Other manuals for PowerEdge 2800
9
Table of contents
Languages:
Other Dell Server manuals
Dell
Dell PowerEdge R910 Technical manual
Dell
Dell PowerEdge 7150 User manual
Dell
Dell PowerEdge R300 User manual
Dell
Dell PowerEdge PDU Managed LED User manual
Dell
Dell PowerEdge 860 Technical manual
Dell
Dell DL4300 User manual
Dell
Dell PowerEdge C6320 User manual
Dell
Dell Force10 S2410-01-10GE-24P Installation manual
Dell
Dell EMC PowerEdge T440 User manual
Dell
Dell PowerEdge UPS 500T User manual
Dell
Dell PowerEdge 6400 User manual
Dell
Dell PowerEdge C8000 User manual
Dell
Dell PowerEdge T410 User manual
Dell
Dell Wyse ThinOS T10 User manual
Dell
Dell PowerEdge R810 User manual
Dell
Dell PowerEdge R320 User manual
Dell
Dell PowerEdge T100 User manual
Dell
Dell PowerEdge C8000 User manual
Dell
Dell PowerEdge 2300 Guide
Dell
Dell IP4700 Installation and maintenance instructions
