Dell E1715S Installation instructions
E1715S 1
1
1. Disassembly Procedures:
Step Figure Remark
S1. Remove
the STAND
BASE ASS'Y.
Turnoffpower,
Unplugexternalcables
fromproduct
Note:
Put the monitor on a flat, soft
and clean surface.
Press the button on the red
circle then pull out the
stand follow the arrow,
stand-base assy will be
remove.
E1715S 2
S2. Remove
the REAR
COVER.
Use a Philips-head
screwdriver to remove 6
screws for unlocking
mechanisms.
(No.1~2 screw
size=M4x10;
Torque=12±2kgf.cm
No.5~6 screw
size=P3x4;
Torque=6±1kgf.cm)
Use Penknife to separate
the bezel and rear cove
follow the arrows in
sequence, then you can
take out rear cover.
1 2
3 4
5 6
E1715S 3
3
S3. Remove
the Cable.
Disconnect the key board
harness.
S4. Disconnect
the LED
HARNESS and
FFC CABLE.
Push
Push
E1715S 4
S5. Remove
the MAIN and
POWER
BOARD.
1. Turn over the main
frame.
2. Remove the Insulating
sheet.
Use a Philips-head
screwdriver to remove 4
screws for unlocking Main
board and Power board
(No.1~3 screw
size=M3x6;
Torque=6±1kgf.cm
No.4 screw
size=M4x6;
Torque=6±1kgf.cm）
Use a Philips-head
screwdriver to remove 1
screws for unlocking Main
board
（No.1 screw
size=M3x5;
Torque=6±1kgf.cm）
Use a hex screwdriver to
remove 2 screws for
unlocking mainboard
（No.2~3 Hex screw
Torque= 4.5±0.5kgf.cm）
1
2
3 4
1 2 3
E1715S 5
5
S6. Disconnect
the HARNESS.
S7. Remove
the MAIN
FRAME
S8. Remove
the PANEL
from Bezel
E1715S 6
S9. Remove
the KEY
BOARD.
Use a Philips-head
screwdriver to remove 4
screws for unlocking Key
board
(No.1~4 screw
size=M2x2.5;
Torque=0.7±0.2kgf.cm)
S10.Remove
capacitors
Remove electrolyte
capacitors (red mark)
from printed circuit
boards
Take out bulk cap. pin
solder with soldering
iron and absorber
1 2 3 4
E1715S 7
7
Lift the bulk cap. up and
away from the PCB
E1715S 8
2. Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100 cm2
External electric cable Product has external cables
Component contain refractory ceramic
fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors
(height > 25mm, diameter > 25mm)
3. Tools Required
Listthetypeandsizeofthetoolsthatwouldtypicallycanbeusedtodisassembletheproducttoapoint
wherecomponentsandmaterialsrequiringselectivetreatmentcanberemoved.
ToolDescription:
‐Phillip head Screwdriver
‐HexScrewdriver
‐Penknife
‐Solderingironandabsorber
Other manuals for E1715S
3
Table of contents
Other Dell Monitor manuals
Dell
Dell P2418HTE User manual
Dell
Dell 2707WFP - UltraSharp - 27" LCD Monitor User manual
Dell
Dell E248WFP - 24" LCD Monitor User manual
Dell
Dell C5519Q User manual
Dell
Dell E171FP User manual
Dell
Dell SP190SFP User manual
Dell
Dell SE2422HXB Instructions for use
Dell
Dell G2410H User manual
Dell
Dell U2410 - UltraSharp - 24" LCD Monitor User manual
Dell
Dell P2418HT User manual
Dell
Dell E2422Ht User manual
Dell
Dell P2214Hb User manual
Dell
Dell E2219HN User manual
Dell
Dell C5519Q Manual
Dell
Dell UltraSharp U2413 User manual
Dell
Dell U3821DWb Instructions for use
Dell
Dell D2719HGF User manual
Dell
Dell E2715H User instructions
Dell
Dell U4021QW User manual
Dell
Dell U2424HEB User manual
