Deif 4189340315C User manual

DEIF

A/S

Basic Gen-set Controller

4189340315C (UK)

Operator’s Manual

•

Display readings

•Push-button functions

•Alarm handling

•Log list

DEIF A/S, Frisenborgvej 33 Tel.: +45 9614 9614, Fax: +45 9614 9615

DK-7800 Skive, Denmark E-mail: [email protected], URL: www.deif.com

BGC Operator’s Manual

DEIF A/S Page 2 of 15

Table of contents

1. ABOUT THIS DOCUMENT....................................................................................................3

GENERAL PURPOSE......................................................................................................................3

INTENDED USERS .........................................................................................................................3

CONTENTS/OVERALL STRUCTURE..................................................................................................3

2. WARNINGS AND LEGAL INFORMATION ...........................................................................4

LEGAL INFORMATION AND RESPONSIBILITY ....................................................................................4

ELECTROSTATIC DISCHARGE AWARENESS.....................................................................................4

SAFETY ISSUES............................................................................................................................4

NOTES.........................................................................................................................................4

3. GENERAL PRODUCT INFORMATION.................................................................................5

INTRODUCTION.............................................................................................................................5

TYPE OF PRODUCT.......................................................................................................................5

4. DISPLAY PUSH-BUTTONS AND LEDS...............................................................................6

PUSH-BUTTON FUNCTIONS............................................................................................................6

LED FUNCTIONS ..........................................................................................................................8

5. DISPLAY AND MENU STRUCTURE ..................................................................................10

LCD DISPLAY.............................................................................................................................10

MENU STRUCTURE .....................................................................................................................10

6. ALARM HANDLING AND LOG LIST ..................................................................................15

ALARM HANDLING.......................................................................................................................15

LOG LIST....................................................................................................................................15

BGC Operator’s Manual

DEIF A/S Page 3 of 15

1. About this document

This chapter includes general user information about this manual concerning the general purpose,

the intended users and the overall contents and structure.

General purpose

This document is the Operator’s Manual for DEIF’s basic gen-set controller, the BGC. The

document mainly includes general product information, display readings, push-button functions,

alarm handling descriptions and presentation of the log list.

The general purpose is to give the user important information to be used in the daily operation of

the unit.

Intended users

This operator’s manual is mainly intended for the daily user. On the basis of this document the

daily user will be able to carry out simple procedures such as start/stop and control of the

generator set.

Contents/overall structure

The document is divided into chapters, and in order to make the structure simple and easy to

use, each chapter will begin from the top of a new page. The following will outline the contents of

each of the chapters.

About this document

This first chapter includes general information about the Operator’s manual as a document, e.g.

it deals with the general purpose and the intended users of it. Furthermore, it outlines the overall

contents and structure of the document.

Warnings and legal information

The second chapter includes information about general legal issues and safety precautions

relevant in the handling of DEIF products. Furthermore, this chapter will introduce a note symbol,

which will be used throughout this document.

General product information

The third chapter will deal with the BGC unit in general and its place in the DEIF product range.

Display push-buttons and LEDs

Chapter four provides an overview of the individual push-buttons and LEDs on the front of the

BGC. The functionality of these will be presented.

Display and menu structure

The fifth chapter will provide specific information as to which readings can be made in the

display.

Alarm handling and log list

The sixth chapter will present the handling of alarms and log list.

BGC Operator’s Manual

DEIF A/S Page 4 of 15

2. Warnings and legal information

This chapter includes important information about general legal issues relevant in the handling of

DEIF products. Furthermore, some overall safety precautions will be introduced and

recommended. Finally, the highlighted notes, which will be used throughout this document, are

presented.

Legal information and responsibility

DEIF takes no responsibility for installation or operation of the generator set. If there is any doubt

about how to install or operate the generator controlled by the BGC unit, the company

responsible for the installation or the operation of the set must be contacted.

Electrostatic discharge awareness

Sufficient care must be taken to protect the terminals against static discharges during the

installation. Once the unit is installed and connected, these precautions are no longer necessary.

Safety issues

Installing the BGC unit implies work with dangerous currents and voltages. Therefore, the

installation of the BGC should only be carried out by authorized personnel who understand the

risks involved in the working with live electrical equipment.

Notes

Throughout this document a number of notes with helpful user information will be presented. To

ensure that these notes are noticed, they will be highlighted in order to separate them from the

general text.

The BGC units are not to be opened by unauthorized personnel. If opened anyway,

the warranty will be lost.

Xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

BGC Operator’s Manual

DEIF A/S Page 5 of 15

3. General product information

This chapter will deal with the BGC unit in general and its place in the DEIF product range.

Introduction

The BGC is a part of the DEIF multi-line 2 product family. Multi-line 2 is a complete range of

multi-function generator protection and control products integrating all the functions you need

into one compact and attractive solution.

The multi-line 2 product range consists of different basic versions, which can be supplemented

with the flexible options needed to provide the optimum solution.

The concept of the BGC is to offer a cost-effective solution to gen-set builders who need a

simple generator protection and control unit. Being a part of the multi-line product family the

standard functions of the BGC can be supplemented with a variety of optional functions.

Type of product

The BGC is a micro-processor based control unit containing all necessary functions for

protection of a gen-set and of mains and generator breaker control.

The BGC contains all necessary 3-phase measuring circuits and presents all values and alarms

on the LCD display. The design of the BGC allows it to be built directly into the engine side panel

or the switchboard door.

BGC Operator’s Manual

DEIF A/S Page 6 of 15

4. Display push-buttons and LEDs

This chapter will present the display push-buttons and LEDs of the unit.

Push-button functions

The display unit holds a number of push-button functions, which are presented below.

INFO: Shifts the display 3 lower lines to show the alarm list.

JUMP: Enters a specific menu number selection. All settings have a specific number

attached to them. The JUMP button enables the user to select and display any

setting without having to navigate through the menus (see later).

VIEW: Shifts the first line displaying in the setup menus.

LOG: Shifts the display 3 lower lines to show the event and alarm list. The list holds

150 events. These events are deleted, when the BGC is switched off.

: Moves the cursor left for manoeuvring in the menus.

: Increases the value of the selected set point (in the setup menu). In the daily

use display, this button function is used for scrolling the second line displaying of

generator values.

SEL: Is used to select the underscored entry in the fourth line of the display.

: Decreases the value of the selected set point (in the setup menu). In the daily

use display, this button function is used for scrolling the second line displaying of

generator values.

: Moves the cursor right for manoeuvring in the menus.

BACK: Jumps one step backwards in the menu (to previous display or to the entry

window).

START: Start of the gen-set if ‘SEMI-AUTO’ is selected.

STOP: Stop of the gen-set if ‘SEMI-AUTO’ is selected.

(GB) ON: Manual activation of close breaker and open breaker sequence if ‘SEMI-AUTO’

is selected.

(MB) ON: Manual activation of close breaker and open breaker sequence if ‘SEMI-AUTO’

is selected.

MODE: Changes the menu line (line 4) in the display to mode selection.

BGC Operator’s Manual

DEIF A/S Page 7 of 15

Push-buttons are placed as follows:

INFO:

Shifts the display three lower lines to show the

alarm list

JUMP:

Enters a specific menu number selection

START:

Start of the gen-set if ‘SEMI-AUTO’ is selected

STOP:

Stop of the gen-set if ‘SEMI-AUTO’ is selected

VIEW:

Shifts the first line displaying in the

setup menus

LOG:

Shifts the display three lower lines

to show the event and alarm list

SEL:

Selects the underscored entry in

the fourth display line

MODE:

Changes the display menu line

(line four) to mode selection

BACK:

Jumps one step backwards in the

Generator breaker

ON/OFF Mains breaker

ON/OFF

Power

Self Check OK

Alarm Inh

Alarm

INFO

JUMP

VIEW

LOG

SEL

BACK

START

STOP

Basic Gen-set Controller

multi-lineBGC

Run ON ON

Load

MODE

Auto

BGC Operator’s Manual

DEIF A/S Page 8 of 15

LED functions

The display unit holds 10 LED functions. The colour is green or red or yellow according to the

running situation.

ALARM: LED flashing indicates that unacknowledged alarms are present.

LED fixed light indicates that ALL alarms are acknowledged, but some alarms

remain.

LED turned off indicates that no alarms are present.

POWER: LED indicates that the auxiliary supply is switched on.

Self check OK: LED indicates that the unit is OK.

ALARM INH.: LED fixed light indicates that the inhibit input is ON.

RUN: LED indicates that the generator is running.

(GEN.) OK: LED green light indicates that the voltage/frequency is present and OK.

(GB) ON: LED indicates that the generator breaker is closed.

(MB) ON: LED indicates that the mains breaker is closed.

(MAINS) OK: LED is green, if the mains is present and OK.

LED is red at a mains failure.

LED is flashing green when the mains returns during the ‘Mains OK delay’ time.

AUTO: LED indicates that auto mode is selected.

BGC Operator’s Manual

DEIF A/S Page 9 of 15

The display LEDs are indicating as follows:

Power

Self Check OK

Alarm Inh

Alarm

INFO

JUMP

VIEW

LOG

SEL

BACK

START

STOP

Basic Gen-set Controller

multi-lineBGC

Run ON ON

Load

MODE

Auto

Alarm:

Flashing: Unacknowledged alarm present

Steady: Acknowledged, active alarm present

Power: Indicates aux. supply ON

Self check OK: Indicates self check OK

Alarm inh.: Indicates alarm inhibit active

Generator running

Generator voltage OK

Generator breaker ON

Mains breaker ON

Mains voltage OK

Remote control: ON

Local control: OFF

BGC Operator’s Manual

DEIF A/S Page 10 of 15

5. Display and menu structure

In this chapter the display and the unit menu structure will be presented.

LCD display

The BGC display is a backlit LCD text display containing 4 lines with 20 characters in each line.

There is no control of the light intensity of the display (no dimmer). Basically, all measured and

calculated values can be read in the display. These may be selected via the PC utility software

(USW).

For selection of values see the Designer’s reference handbook.

Menu structure

The BGC display includes two menu systems, which can be used without password entry:

View menu system

This is the daily use menu system designed for the operator. 15 windows are

configurable and can be entered by using the arrow push-buttons.

Setup menu system (not commonly used by the operator)

This menu system is used for setting up the unit, and if the operator needs detailed

information which is not available in the view menu system. Changing of parameter

settings is password protected.

Entry window

When the unit is powered up, an entry window appears. The entry window is the turning point in

the menu structure and as such the gateway to the other menus. It can always be reached by

pressing the BACK push-button 3 times.

The event and alarm list will appear at power up, if an alarm is present.

Table of contents

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual