Decko 82004 User guide
A
B
D
F
C
E
G
H
I
J
M
K
Thank You for your purchase of a finely
crafted piece of furniture from Decko Woods.
The following contains instructions for
assembly as well as care and maintenance
instructions. Please take a moment to
completely read and familiarize yourself with
this information. You will then be ready to
assemble your furniture. If you have any
questions regarding your purchase, please
contact us at 1-800-495-9278
Tools Needed:
-Phillips Head Screwdriver
-Adjustable wrench
NOTE: It is NOT recommended to use power
tools for assembly. They may cause over
tightening and damage to your chair.
Parts List & Hardware
Item Qty Description
A 1 Back Assembly
B 1 Seat Assembly
C 1 Left Leg
D 1 Left Arm
E 1 Right Leg
F 1 Right Arm
G 2 Back Supports
H 10 Machine Screw 6 x 50 mm
I 10 Washer - 6mm
J 10 Nut - 6mm
M 10 Wood Screw - 4mm x 40mm
K 2 Wood Screw 5 x 60mm
CARE & MAINTENACE ADIRONDACK CHAIR ASSEMBLY AND CARE INSTRUCTIONS
For Model# 82004
FINISHING TIPS (For unfinished wood)
Your Decko Woods furniture is made from high quality, select grade fir. It is naturally resistant to
rot and decay. Proper finishing will help assure the beauty and durability of your chair. If you
choose to paint your chair, you should use an exterior grade primer followed by a high quality
exterior oil or latex based paint. If you choose to have the product retain its natural color, you
should apply a natural oil-based stain or preservative annually or as needed. When finishing,
make sure you also treat the ends of the wood parts that come in contact with the ground.
If you leave the chair without adding any finish, it will weather to a silver gray color.
Contact your local paint store, home center or hardware store for other finishing
recommendations.
MAINTENANCE
Very little maintenance is required for your furniture. Periodically check all fasteners to make
sure they are properly secured. Re-tighten if necessary.
MANUFACTURER’S LIMITED WARRANTY
This product is covered under the manufacturer’s 1 year limited warranty against defect in
workmanship and materials. If your furniture fails structurally during normal use within on year of
purchase, the manufacturer will repair or replace the defective piece at no charge.
The warranty excludes furniture used for commercial purposes, furniture damaged by acts of
nature, abuse or lack of proper care or corrosion or rusting of hardware.
Proof of purchase (dated register receipt) is required for warranty claims.
Decko Products
2301 Traffic St. NE
Minneapolis, MN 55413
1-800-495-9278
NOTE: Diagrams are not drawn to scale. Construction in diagrams may differ from actual chair.
STEP 1
Lay seat assembly (B) flat on the
ground. Using two 4 x 40 mm wood
screws (M), attach the back assembly
(A) to the seat assembly. (NOTE:
There are no pre-drilled holes in the
seat assembly. The screws will self
thread into the wood).
STEP 2
Carefully lay the chair on its side as
shown. Using three 6 x 50 mm machine
screws (H) with flat washers (I) and nuts
(J) attach the right leg (E) to the seat
assembly. (The leg will be positioned
with the arm brace facing upward and to
the front of the seat assembly)
Using two 6 x 50 mm machine screws (H)
with flat washers (I) and nuts (J) attach
one back support (G) to the seat
assembly. Attach other end of back
support to back assembly using two 4 x
40 mm wood screws (M)
NOTE: Do not completely tighten all
fasteners at this time. Leave them a
bit loose until the final step.
STEP 3
Using two 4 x 40 mm wood screws (M)
attach the right arm (F) to the leg.
Attach the back of the arm to the back
assembly using one 5 x 60 mm wood
screw (K)
STEP 4
Turn chair onto its other side. Using
instructions from STEP 2 attach the
left leg (C) and back support (G) to the
seat and back assembly.
STEP 5
Using instructions from STEP 3 attach
the left arm (D) to the leg and back
support assembly
STEP 6
Completely tighten all fasteners and
enjoy your new chair.
ASSEMBLY TIPS
-Carefully read all of the steps and acquaint yourself with the
wood parts and fastener sizes before starting assembly.
-Separate fasteners by size before starting assembly
-During assembly all hardware should be semi tightened until the
final step
Other Decko Indoor Furnishing manuals
