Danrou KCM-7790DR User manual
DIGITAL WIRELESS 9” LCD
MONITORING SYSTEM
WITH SD CARD RECORDING
MODEL: Danrou KCM-7790DR
Feature list:
850nm IR Led visible distance up to 15m
9” TFT Lcd Digital panel (800 RGB x 480)
Two way audio
Scan function
PIR trigger or Video motion detect alert& recording
Manual recording
Touch button operation
Schedule recording separate settings from Monday to Sunday
Micro SD Card capacity up to 64GB
One LCD monitor can pair four cameras
Frame rate: Cam x 2 : 720p x1 @ 15 fps or Cam x 2 : VGA x2 @ 30 fps or Cam x 4 : VGA x 4 @ 15 fps
Individual recording files
5 Seconds pre-recording
LCD : 5v DC 2A Power adaptor (+/-5%)
Camera: 9v DC 600mA (+/-5%)
RF range: 150 meter (Line of sight)
Quad view
Remote view and playback by Android or iOS smart phone
The system includes the following components:
Wireless Receiver
Front Panel buttons
1. LCD Screen –Displays video from the camera(s) or displays system operations.
Item
Button
Function
2.
:Talk back
Enable two-way audio Intercom
3.
: Motion Recording
Activate / deactivate motion recording.
4.
: Manual Recording
Activate / deactivate manual recording.
5.
: Change Channel
Switch between connected cameras.
6.
: Quad / Sequence Mode
Switch between Sequence and Quad (up to 4-channels)
viewing mode.
7.
: Zoom
Switch between 2x digital zoom and normal viewing mode.
8.
: Delete File
Delete highlighted files in Playback mode.
9.
: Menu
Open Main Menu. Return to previous menu / exit menus.
10.
: Joystick
Move left / right / up / down to move the cursor in menus.
Push to enter Playback mode.
Back controls
1. Wireless Antennas: Position the antennas as needed for best reception.
2. Power Button: Press and hold to turn the receiver on / off. Press and release while the unit is
powered on to turn Scan mode.
3. Receiver Stand
4. Speaker
5. Stratus UID Number / QR Code: Unique ID number for connection to the system on a smartphone /
tablet.
6. Ethernet Port (RJ45): Connect the receiver to your router using the included Ethernet cable to enable
smartphone / tablet connectivity.
7. Power Port: Connect to a local power outlet using the included power adapter.
8. Volume Controls: Turn the receiver volume up and down.
9. micro SD Card Slot: Insert up to a 64GB micro SD card.
10. USB Port: Used for service purposes only.
11. Reset: Using a paper clip or other thin object, push the reset button to restore the system to its
default settings.
12. Power Indicator LED: Glows when receiver is connected to power.
Wireless Camera
1. IR LEDs –Infrared LEDs provide
viewing in no/low light conditions
2. Camera Lens –Catches the video in
front of the lens and transmits video from
camera to receiver.
3. PIR Sensor –Detects motion in front of the lens and
emits detection signal to transmitter.
4. Speaker –Produces the sound transmitted from the
receiver.
5. Camera Antenna –Sends & receives signals to or
from the receiver.
6. Wall Mounting Bracket –Use the bracket to mount the camera on a wall or other flat surfaces.
7. AC Adaptor Jack –Plug the AC adaptor to the jack for camera’s power supply.
8. Pair Button –The pair button is located on the back of the camera, it is used to pair the camera with
receiver.
Note: This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between day
mode and night vision mode, an audible clicking noise may be heard coming from the camera. This
clicking is normal, and indicates that the camera filter is working.
Camera Installation
Before you install the camera, carefully plan where and how it will be positioned, and where you will
route the cable that connects the camera to the power adaptor.
Before starting permanent installation, verify its performance by observing the image on the receiver
when camera is positioned in the same location/position where it will be permanently installed and the
receiver is placed in the location where it will be used most of the time.
Installation Warnings
·Aim the camera(s) to best optimize the viewing area: Select a location for the camera that provides a
clear view of the area you want to monitor, which is free from dust, and is not in line-of-sight to a strong
light source or direct sunlight.
·Avoid installing the cameras where there are thick walls, or obstructions between the Cameras and the
Receiver.
·Select a location for the camera that has an ambient temperature between 14°F~104°F(-10°
C~40°C)
·Not intended for submersion in water. For outdoor use, installation in a sheltered location is
recommended
Night Vision
This camera has built-in IR LEDs, which provides the camera with the ability to view images in no/low
light conditions.
Mounting Positions
You may mount your camera on a wall, ceiling, or counter. See the images below for recommended
configurations of the camera stand and antenna.
Wall Ceiling Counter
NOTE: For ceiling installation, position the antenna as high
as the ceiling allows. See the"Ceiling" mounting position in
the figure above.
To Install the Cameras
1. Use the included mounting screws to mount the camera to
the mounting surface:
· Mark the positions of the screw holes on the mounting
surface.
· Drill holes and insert the drywall plugs (included) as needed.
· Firmly attach the camera to the mounting surface using the included
screws.
NOTE (1): If you are running the power cable through the mounting
surface, connect power before firmly attaching the camera to the
mounting surface.
NOTE (2):
If you run the power cable along the mounting surface, the
cable must go through the cable notch on the camera base. This will
keep the camera base flush to the mounting surface.
NOTE (3): The camera can also be placed on a flat surface, such as a Table or Shelf, and no mounting
hardware is required.
2. Loosen the thumbscrews (1, 2) and the adjustment ring (3) by turning them counter clockwise.
3. Adjust the angle of the camera until the desired view is set. Tighten the thumbscrews and the
adjustment ring to secure the camera’s position.
NOTE: You can install additional cameras (maximum of 4 cameras). When adding cameras that were
not included in the original box, you will need to pair up the cameras with the receiver. Refer to the
camera pairing section of this manual.
4. Connect the power cable from the camera to the weatherproof power connector. Plug the power
adapter into a power outlet or surge protector.
NOTE: Power cables are only weatherproof when fully inserted at the connection point.
Power cables may not be submerged in water.
Make sure is the DC 9V for camera, and DC 5V for Receiver
Make sure the power adaptor is placed into a grounded outlet or surge bar to protect the camera from
power fluctuations.
1 Using the system
By default, the camera(s) included with your system are automatically paired to the receiver. The
camera(s) and receiver will communicate with each other once they are powered on.
Note: It is recommended to power on the cameras before powering on the receiver.
1.1 Understanding the On-screen Display
With camera 1 properly connected and powered on, the system displays a full-screen live view of the
camera.
With more than one camera properly connected and powered on, the system displays up to 4 channels
in split screen with the live view of each camera. The figure below shows the display configuration for 2
cameras connected.
1Signal Indicator –The signal indicator shows the strength of the signal being received from the
camera. The number of bars in the Signal Indicator shows the strength of the signal. One or no bars
indicates the signal is poor, and 4 bars indicate a very strong signal.
Note
•If the signal is low (e.g.,1 or 2 bars) adjust the antennas, or reposition the cameras or receiver for
best performance.
•The signal indicator is not shown during Quad mode.
Signal Indicators:
O
OUT OF RANGE Warning
When the receiver can’t get signal from cameras, warning message will be displayed. Reposition the
camera, or check the camera power connection.
2 Channel Indicator–Displays the current channel number you are presently viewing. If viewing
multiple cameras at once, the camera indicator will appear above each video display.
Press Cam button to view camera in manual switching mode.
Under Quad mode :
*Press view button to enter automatically switch between channels.Press view again to enter
Quad mode.
*Press joystick button 1.2.3.4 to accordingly switch available cam1,cam2,cam3,cam4.
3 micro SD Card Indicator –When a microSD card is inserted into the SD card slot, the indicator will
be shown on the LCD screen. A white icon shows that a microSD card with available recording space is
inserted in the receiver. A red icon indicates the microSD card is full.
4 Network status Indicator –A red icon shows that the connection has failed or the system is
not connected to a network. A green icon shows that the system is connected to the Internet and
tell you the monitor connect with internet mode. A yellow icon shows that the system is connected
to the intranet and tell you the monitor connect with intranet mode.
Remote connection Indication- When a smartphone / tablet is accessing the system remotely, the
network status indicator changes to a remote connection icon .
5 Talk back Indicator- Touch and hold on the monitor then talk back to the camera, the indicator .
will be shown on the LCD screen.
6 Recording Indicator–"REC" appears when recording is in progress. If viewing and recording video
from multiple cameras at once, the recording indicator will appear above each video display where
recording is enabled
7 Zoom Indicator-Press the Zoom button on the front panel of monitor to enter “×2”mode, the
indicator will be shown on the LCD screen. shows on the screen ,you can use the joystick button to
Table of contents
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual