Danfoss TP9000 Guide

TP9000

Installation Instructions

User Instructions

Instrukcja montażowa

Instrukcja obsługi

Electronic Programmable

Room Thermostat plus

Domestic Hot Water Timer

Certification Mark

TP9000

Installation Instructions 3-14

Product Speciﬁcation 3

Installation 4

Cable Access and Wiring 5

Installer Advanced Programming Options 8

User Instructions 15-31

What is a Programmable Room Thermostat 15

Preset programmes 17

Setting Date and Time 18

Changing Preset Programmes 20

User overrides 27

User Advanced Programming Options 33

Overview of Installer Selectable Features 37

Setting References 39

Index

DANFOSS HEATING 3

Please note: This product should only be installed by a qualiﬁed

electrician or competent Heating installer, and should be in

accordance with the current edition of the IEEE wiring regulations.

Speciﬁcation 230V model 24V model

Power supply 230 Vac, ±15%,

50/60 Hz

24 Vac, ±15%,

50/60 Hz

Switching action

2 x SPDT internally linked, Type 1BS

Unit switch rating 230 Vac, 3(1)A 24Vac, 3(1)A

Memory Backup Retained for life of product

Heat Temperature Range

Setting

5°C - 30°C

Factory Set Calendar Clock Automatic Summer/Winter time

change

Remote Sensor Inputs

(‘A’ models only)

Can be set by installer for remote

sensor, limited sensor, window con-

tact, tele-switch or outdoor sensor

Programme resolution ± 1 minute

Timing Accuracy ± 1 minute

Dimensions, mm (W, H, D) 135 x 88 x 32

Design standard EN 60730-2-7 +EN60730-2-9

Control Pollution Situation Degree 2

Rated Impulse Voltage 2.5 kV

Ball Pressure Test 75°C

Product speciﬁcation

Installation Instructions

TP9000

Installation

• Remove wallplate from unit by unscrewing the two screws on the

bottom edge of the unit.

• From the top left hand corner of the wallplate, there must be

clearances of at least 140 mm to the right, 15mm to the left, 30mm

above and 100mm below in order to mount the plug-on module.

• The wallplate must be securely mounted either directly to the

wall using suitable wood screws or to a ﬂush mounted 1-gang

electrical accessory box using M3.5 screws.

• Cable access can either be from behind for concealed cabling, or

from below for surface cabling. If surface cable is used, cut out

cable access slot on plug-on module prior to mounting.

• For wiring connections refer to diagram on page 6.

The TP9000 is double insulated and does not require an earth

connection, however a parking terminal is provided on the

wallplate. This is clearly marked with an Earth symbol.

• Prior to mounting the plug-on module, DIL switches on the rear of

the plug-on module must be set. See diagram below for available

options.

• Mount plug-on module to wallplate by locating tabs on top of

wallplate in apertures on rear of module, hinge down and press

ﬁrmly to wallplate before tightening securing screws on bottom

of wallplate.

Keyboard disabled

Reset disabled Reset enabled

Keyboard enabled

OFF ON

Sw. No.

 Prior to mounting the unit the 2 DIL switches on the rear of the

unit have to be moved to the required position. The factory

presets are shown below.

DANFOSS HEATING 5

IMPORTANT: The supply to this unit should by wired via a double pole

isolationswitchinaccordancewithBSEN60730-1, i.e.onewhichprovides

air gaps of at least 3mm in both poles of the mains, and incorporates a 3

amp fuse. It is strongly recommended that solid conductors be used.

Clearance for

screwdriver

access

Surface fixed cable

bottom entry knockouts

Rear entry

cable access

N &

looping

terminals

Wall or

Plaster box

fitting

Terminal block

Outline of unit

30mm minimum

C/L

 Thermostat and Remote Room Sensor:

Fix at a height of approximately 1.5m from the ﬂoor, away from

draughts or heat sources such as radiators, open ﬁres or direct

sunlight.

TP9000

Wiring

NOTE:

The TP9000 does not have voltage free contacts, therefore it is NOT

suitable for connection to extra low voltage equipment (i.e. > 50

Volts).

Remote Sensor to be wired with 1mm 2 core double insulated cable

only. Cable length should not exceed 50 metres. Sensor cable should

NOT be run parallel to mains cable.

Remote sensor inputs

The TP9000 incorporates an input which can be used to connect one

of the following:

1) remote room temperature sensor

2) limit sensor, for example, ﬂoor temperature sensor (sold as

accessory).

3) window contacts, card reader contacts, outdoor sensor (sold as

accessory) or teleswitch contacts.

See Installer Advanced Programming Options for set-up instructions.

DANFOSS HEATING 7

Remote sensor inputs

Terminals 5 and 6 are the designated remote sensor inputs. These can

be found on the top right hand side of the wallplate.

Window or

teleswitch

contact

(NO or NC)

Teleswitch

contact (NC)

Window

contact (NC)

Conﬁgured for

remote room,

limit or outdoor

sensor

Conﬁgured for

window contact or

other contact such

as teleswitch

Conﬁgured for

window contact

and other contact

such as teleswitch

TP9000

Installer advanced

programming options

TP9000 incorporates a number of advanced features which can be set

by the user. These are accessed via a User Advanced Programming

Mode, please refer to User Advanced Programming in the user

instructions for details (see page 33)

Installer advanced programming options

TP9000 incorporates an additional number of advanced features which

can be set by the installer to improve the operating eﬃciency of the

system and where required, to change the user functionality of the

product. These are accessed via an Installer Advanced Programming

Mode. These settings are optional and need only be made if there is a

demand for the enhanced functions.

Service Interval Timer

Instructions on how to access this feature are available from our

customer support desk. Please note these are only issued to boni-ﬁde

Heating installers.

Entering Installer Advanced Programming Mode

To access the Installer Advanced Programming Mode follow the steps

below:

a) Press and hold Vand PROG for 3 seconds to

enter User Advanced Programming, the display

will change to ﬁgure opposite.

b) Press and hold V, Λand PROG for 5 seconds

to enter Installer Advanced Programming, the

display will change to ﬁgure opposite.

DANFOSS HEATING 9

c) Use +and -keys to scroll backwards and forwards between options

then Vand Λkeys to change the option settings. The ﬂashing digit

on the right hand of the display indicates the number of the selected

option. The large characters display the option value selected.

d) To return to RUN, press and hold PROG until the display returns to

RUN mde.

Option 30 - Set upper limit of temperature range

This allows the upper limit of the thermostat setting

range to be electronically limited. Press +until

Option 30 is displayed, use Vand Λto select required

setting.

Setting 40 - 5°C (factory setting is 30°C)

Option 31 - Set lower limit of temperature range

This allows the lower limit of the thermostat setting

range to be electronically limited. Press +until

Option 31 is displayed, use Vand Λto select required

setting.

Setting 5 - 40°C (factory setting is 5°C)

Option 32 - Enable Oﬀ at lower limit

This enables an OFF function to be selected if a set

point below the lower limit is selected. Press +until

Option 32 is displayed, use Vand Λto select required

setting.

Setting 0 Disabled

Setting 1 Enabled (factory setting)

Option 33 - Enable On at upper limit

This enables an ON function to be selected if a set

point above the upper limit is selected. Press +until

Option 33 is displayed, use Vand Λto select required

setting.

Setting 0 Disabled (factory setting)

Setting 1 Enabled

TP9000

Option 34 - Select On/Oﬀ or Chrono-proportional

This allows the thermostat to be set to run in On/Oﬀ

mode or for a chrono-proportional cycle rate to be

selected. Press +until Option 34 is displayed, use V

and Λto select required setting.

0On/Oﬀ

33 cycles per hour

66 cycles per hour (factory setting)

99 cycles per hour

12 12 cycles per hour

Option 35 - Set integration time (Option 34 set to 3, 6, 9 or 12)

(seek advice prior to adjusting)

This adjusts the integration time of the PI algorithm

to increase control accuracy. It is only active if

option 34 has been set to Chrono 3, 6, 9 or 12.

It should only be adjusted after seeking advice

from the manufacturer. Press +until Option 35 is

displayed, use Vand Λto select required setting.

2.5 Integration time set to 2.5% (factory setting)

5Integration time set to 5%

10 Integration time set to 10%

Option 36 - Set temperature override rule

This establishes the degree of temperature override

available to the user. Press +until Option 36 is

displayed, use Vand Λto select required setting.

Setting 0 No limit (factory setting)

Setting 1 Limited to ±2°C

Setting 2 No override allowed

Other manuals for TP9000

Table of contents

Languages:

Other Danfoss Thermostat manuals

Danfoss

Danfoss ECL Comfort 310 User manual

Danfoss

Danfoss 088U0215 User manual

Danfoss

Danfoss Basic Plus2 User manual

Danfoss

Danfoss CF-RF User manual

Danfoss

Danfoss ECtemp 530 User manual

Danfoss

Danfoss TP4000 Range User manual

Danfoss

Danfoss TP5001 series User manual

Danfoss

Danfoss living connect User manual

Danfoss

Danfoss RET M Operating instructions

Danfoss

Danfoss FP715Si User manual

Danfoss

Danfoss TP5001 series User manual

Danfoss

Danfoss KP61 User manual

Danfoss

Danfoss RT 14L User manual

Danfoss

Danfoss DEVI DEVIreg 530 User manual

Danfoss

Danfoss ECL Comfort 310 User manual

Danfoss

Danfoss ECtemp 532 User manual

Danfoss

Danfoss TP9000 Si User manual

Danfoss

Danfoss FH-RT Manual

Danfoss

Danfoss ECL Comfort 210 User manual

Danfoss

Danfoss DEVIreg Touch User manual

Danfoss

Danfoss TP4 Assembly Instructions

Danfoss

Danfoss RET1000 MD User manual

Danfoss

Danfoss living connect Z User manual

Danfoss

Danfoss TPONE-RF User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide