Danfoss REP24 User manual

Table of contents

Other Danfoss Thermostat manuals

Danfoss

Danfoss DEVIreg Multi User manual

Danfoss

Danfoss living connect Z User manual

Danfoss

Danfoss REP24CO3 User manual

Danfoss

Danfoss ECL Comfort 110 User manual

Danfoss

Danfoss RTW-RA User manual

Danfoss

Danfoss ECtemp 531 User manual

Danfoss

Danfoss Link DBR User manual

Danfoss

Danfoss WP75-RF User manual

Danfoss

Danfoss FH-CWP User manual

Danfoss

Danfoss RMT-24 User manual

Danfoss

Danfoss living connect Z User manual

Danfoss

Danfoss CF-RF User manual

Danfoss

Danfoss TP5001 series User instructions

Danfoss

Danfoss GreenCon RC-C2 User manual

Danfoss

Danfoss ST-D1 User manual

Danfoss

Danfoss DEVIreg 530 User manual

Danfoss

Danfoss Link FT User manual

Danfoss

Danfoss RET2000B-RF + RX1-S User manual

Danfoss

Danfoss TP7000 Series User manual

Danfoss

Danfoss TP9000 User manual

Danfoss

Danfoss Eco User manual

Danfoss

Danfoss FH-RT Manual

Danfoss

Danfoss ECL Comfort 310 User manual

Danfoss

Danfoss Living Eco User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide

REP24 24V electronic dial setting thermostat

with proportional output

and manual heat cool selection

Installation and Instructions

2

INDEX

Installation 3-9

Specication 3

Mounting 4-5

Wiring 6

DIL switch settings 7

Mounting 8

Locking & Limiting 9

User Instructions 10-12

Setting the temperature 10

Frost Protection 10

Standby Mode 10

Understanding your thermostat 11

Index

3

Specication

Features REP24

Power supply 24 Vac, ± 15%

Control Output 0-10 Vdc

Control Method P + I

Proportional Band 2° K

Temperature range 10-30°C

Maximum ambient temperature 45°C

Control pollution Degree 2

Design standard EN 60730-2-9

Rated impulse voltage 2.5kV

Ball hardness test 75°C

Dimensions (mm) 85 wide x 86 high x 42 deep

Installation Instructions

4

Mounting

Mounting

5

Fix at a height of 1.5m approx from the oor, away from

draughts or heat sources such as vents, heating elements or

direct sunlight.

Mounting

Mounting

6

Wiring

1

B

A234

24 Vac

0V 24V 0V V out

output

0-10V

ELECTRONICS

Wiring

7

DIL switch settings

Slide the DIL switches to the settings required.

HEAT - proportional output will activate if temperature is below

the setpoint. Frost protection mode is available (see page 10 ).

COOL -

proportional output will activate if temperature is above

the setpoint. Frost protection not available in cooling mode.

MOT -

Motorised valve actuator selection.

WAX -

Wax valve actuator selection.

MOT WAX

Heat Cool

DIL switch settings

Sw. On

8

Mounting

Mounting

9

Locking & Limiting

Locking - setting the thermostat at a temperature which

cannot be altered by the user.

Limiting - allowing the user to alter the temperature within

a predened range, which is less than the full range of the

product (i.e. between 18-22°).

Locking & Limiting

10

Setting the temperature

Turn setting dial to required temperature.

Frost Protection

To activate frost protection, turn the dial below 10°C. Frost

protection becomes active at 8°C. If the temperature in the

room drops below 8°C then the output will activate.

When frost protection is activated the right LED will turn

orange.

Standby Mode

In cooling mode, the standard frost protection is not available;

instead there is standby mode. When the dial is turned past

10°C the unit enters standby mode and cooling will be inactive

until dial is turned up past 10°C.

Display / Setting the temperature

User Instructions