Danfoss ECtemp 330 User manual
ECtemp 330 (+5 to +45°C)
Electronic Thermostat
Installation Guide
electricheating.danfoss.com
ECtemp 330 (+5 to +45°C)
Installation Guide2
Danfoss A/S is not liable or bound by warranty if these in-
structions are not adhered to during installation or service.
The English language is used for the original instructions.
Other languages are a translation of the original instructions.
© 2013 Copyright Danfoss A/S
ECtemp 330 (+5 to +45°C)
3Installation Guide
1 Introduction
ECtemp 330 is an electronic thermostat to be installed in
electric cabinets with DIN rail attachment. The thermostat
must be installed via an all-pole disconnection switch. Ei-
ther a floor sensor or an external room sensor must be used
to measure and control the desired temperature.
The thermostat has a button to adjust the temperature
setting with a scale from +5 to +45°C. An LED indicator
shows standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
ectemp.danfoss.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specifications . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . 6
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Warranty. . . . . . . . . . . . . . . . . . . . . . . . 9
5 Disposal Instruction . . . . . . . . . . . . . . . . 9
ECtemp 330 (+5 to +45°C)
Installation Guide4
1.1 Technical Specifications
Operation voltage 220-240V~, 50Hz
Standby power consumption Max 0.25W
Relay:
Resistive load
Inductive load
Max 16A / 3680W @ 230V
cos φ= 0.3 max1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0°C
25°C
50°C
42kOhm
15kOhm
6kOhm
Hysteresis ± 0.2°C
Ambient temperature 10°C to +50°C
Lowering in economy periods -5°C
Temperature range +5 to +45°C
Cable specification max 1x4mm² or 2x2,5mm²
Ball pressure temperature 75°C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20°C to +65°C
IP class 20
ECtemp 330 (+5 to +45°C)
5Installation Guide
Protection class Class II -
Dimensions 86 x 36 x 58mm
Weight 83g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned off
before installation.
IMPORTANT: When the thermostat is used to control a
floor heating element in connection with a wooden floor or
similar material, always use a floor sensor and never set the
maximum floor temperature to more than 35°C.
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualified installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
ECtemp 330 (+5 to +45°C)
Installation Guide6
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Please observe the following placement guidelines:
• Install the thermostat in an electric cabinet with DIN
rail attachment or a separate DIN attachment accord-
ing to local regulation on IP classes.
• Do not place the thermostat in a way that it will be
exposed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Click the thermostat on to the DIN rail attachment.
2. Connect the thermostat according to the connection
diagram.
+5°C to
+45°C
ECtemp 330 (+5 to +45°C)
7Installation Guide
N
L
PE
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the floor sensor in a conduit in
the floor.
3. Turn on the power supply.
3 Settings
If a floor sensor is used, please be aware of the following:
• The floor temperature is measured where the sensor
is placed.
• The temperature of the bottom of a wooden floor can
be up to 10 degrees higher than the top.
ECtemp 330 (+5 to +45°C)
Installation Guide8
• Floor manufactures often specify the max tempera-
ture on the top surface of the floor (usually 27-28˚C).
• Always use a floor sensor to control floor heating.
Without a floor sensor, the temperature control may
be less accurate and you risk overheating the floor.
Thermal
resist-
ance
[m²K/W]
Examples of
flooring
Details Approximate
setting for
25˚C floor
temperature
0.05 8 mm HDF based
laminate
> 800 kg/m³ 28˚C
0.10 14 mm beech
parquet
650 - 800
kg/m³
31˚C
0.13 22 mm solid oak
plank
> 800 kg/m³ 32˚C
< 0.17 Max. carpet thick-
ness suitable for
floor heating
acc. to EN
1307
34˚C
0.18 22 mm solid fir
planks
450 - 650
kg/m³
35°C
ECtemp 330 (+5 to +45°C)
9Installation Guide
4 Warranty
5 Disposal Instruction
ECtemp 330 (+5 to +45°C)
Installation Guide10
Other manuals for ECtemp 330
3
Table of contents
Other Danfoss Thermostat manuals
Danfoss
Danfoss TP5000 si range Guide
Danfoss
Danfoss RET2000B-RF User manual
Danfoss
Danfoss RT 103 User manual
Danfoss
Danfoss TP75 Operating manual
Danfoss
Danfoss TP4000 Range User manual
Danfoss
Danfoss ECtemp 535 User manual
Danfoss
Danfoss ECL Comfort 210 User manual
Danfoss
Danfoss CP10C User manual
Danfoss
Danfoss ECtemp 550 User manual
Danfoss
Danfoss ECL Comfort 310, A302 User manual
Danfoss
Danfoss BasicPlus2 User manual
Danfoss
Danfoss TP75-RF User manual
Danfoss
Danfoss LX 420 User manual
Danfoss
Danfoss ECL Comfort 310, A367 User manual
Danfoss
Danfoss 088L5130 User manual
Danfoss
Danfoss ECtemp Touch User manual
Danfoss
Danfoss TP7001 series User manual
Danfoss
Danfoss TP9000 Guide
Danfoss
Danfoss GreenCon RC-C2 User manual
Danfoss
Danfoss Icon Master User manual
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
