Danfoss CET2000B-RF User manual

CET2000B-RF + RX1-S + CS2

Wireless Electronic Hot Water Cylinder Thermostat

Installation Guide

Danfoss Heating

CET2000BRF

For a large print version of these instructions

please call Marketing on 0845 121 7400.

Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other

printed material. All trademarks in this material are property of the respective companies.

Hearby, Danfoss A/S declares that the radio equipment type CET2000B-RF + RX1-S is in

compliance with directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address, http://heating.danfoss.co.uk/xdoccat/14_CATC-J_MNU17497125_SIT313.html

Danfoss Heating 3

Product Specications

CET2000B-RF RX1-S

Operating Voltage 2.5 – 3 VDC

(2xAA alkaline batteries) 230Vac 50Hz

Output Relay - 1 x SPDT Type 1B

Switch rating - 3A (1) at 230Vac

Output - Volt free

Setting temp. range 40-65°C -

Maximum ambient temp. 0-45°C

Battery lifetime 2 years -

Max. range 30 metres

Operating frequency 433.92MHz <1mW ERP

IP Rating IP20 IP40

Control On-O

Operating mode Domestic Hot Water Heating

Construction EN 60730-2-9 EN 60730-1

Control pollution situation Degree 2

Rated impulse voltage - 2.5kV

Ball pressure test 75°C

Dimensions H84 x W84 x D35 H84 x W84 x D28

Software classication A

Important note RF products: Ensure that there are no large metal objects, such as

boiler cases or other large appliances, in line of sight between the transmitter and

receiver as these will prevent communication between thermostat and receiver.

CET2000B-RF

1. The clamp on sensor should

be mounted onto the

cylinder wall at a height

equivalent to ½ the height

of the cylinder. Care should

be taken to remove any

insulation material from

the cylinder and to ensure

that the copper surface of

the cylinder is clean. See

diagram opposite for details.

This product should only be installed by a qualied

electrician or competent heating installer, and must be

in accordance with local wiring regulations.

1/2 c

ylinder

height

For insulation thicker than 25mm

and up to 55mm thick, use the

extra cover supplied as a spacer to

ensure that the sensor is held in

firm contact with the cylinder wall.

Installation

Danfoss Heating 5

2. Before attaching the sensor to the cylinder using the strap

provided, connect a 2-core cable to the sensor to allow

interconnection to the thermostat setting unit.

3. Apply the contact paste provided to the part of the sensor

in contact with the cylinder and clamp the sensor to the

cylinder wall.

A spacer piece is provided for use with cylinders that have

thick insulation (see page 6).

4. Mount the thermostat wallplate on to a wall next to the

cylinder. Connect the cable from the sensor to terminals 1

& 2 of the wallplate (see wiring diagram on page 7).

5. Now mount the thermostat setting unit onto the wallplate

(see diagrams on page 9).

CET2000B-RF

1/2 cylinder

height

For insulation thicker than 25mm

and up to 55mm thick, use the

extra cover supplied as a spacer to

ensure that the sensor is held in

rm contact with the cylinder wall.

Danfoss Heating 7

Sensor Wiring

CS2

sensor

1 2 3

CET2000B-RF

Cable specication: minimum cross section 0.5mm2

CET2000B-RF

Installation - RX1-S Receiver unit

ELECTRONICS

234

COM ON OFF

230Vac

Please Note: This product should only be installed by a

qualied electrician or competent heating installer, and must

be in accordance with local wiring regulations.

Danfoss Heating 9

Mounting - CET2000B-RF

CET2000B-RF

Hard Wired Heating with Wireless Hot Water

Control, 3 Port Mid-Position Valve

ELECTRONICS

NL123

ELECTRONICS

NL2

HTG OFF 3

HW ON 4

HTG ON

230Vac

HW OFF

RET1000MS

Room Thermostat

RX1-S Receiver -

paired to CET2000B-RF

FP715 Programmer

3 Port Mid-Position Valve

FP715 Programmer

Boiler

Pump

NL2

blue

brown/

white

orange

grey

N L N L SW.L

This manual suits for next models

Table of contents

Other Danfoss Thermostat manuals

Danfoss

Danfoss REPI Series User manual

Danfoss

Danfoss HC75A-1 Operating manual

Danfoss

Danfoss Icon Master User manual

Danfoss

Danfoss TP5E User manual

Danfoss

Danfoss Devireg 535 User instructions

Danfoss

Danfoss C37 User manual

Danfoss

Danfoss BasicPlus2 User manual

Danfoss

Danfoss BasicPlus2 WT-D User manual

Danfoss

Danfoss REPI Series User manual

Danfoss

Danfoss Eco User manual

Danfoss

Danfoss ECtemp Next Plus User manual

Danfoss

Danfoss TP5000-RF Operating instructions

Danfoss

Danfoss RET2000 B User manual

Danfoss

Danfoss TP5000 si range Guide

Danfoss

Danfoss ECL Comfort 310, A361 User manual

Danfoss

Danfoss DEVIreg 532 User manual

Danfoss

Danfoss HCT-3 User manual

Danfoss

Danfoss ST-S2 User manual

Danfoss

Danfoss 088L5133 User manual

Danfoss

Danfoss ECL Comfort 110 User manual

Danfoss

Danfoss living connect User manual

Danfoss

Danfoss 088L5130 User manual

Danfoss

Danfoss WT-DR User manual

Danfoss

Danfoss LX205T User manual

Popular Thermostat manuals by other brands

EWELLY

EWELLY EW-181 manual

Prolon

Prolon T1100 Hardware guide

Computherm

Computherm Q20 operating instructions

Heatmiser

Heatmiser neoStat user manual

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA user manual

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat user manual

Saswell

Saswell SAS920XWHB-7-S-RF User manual and warranty card

Aircalo

Aircalo TFP1-ET85P2 operating manual

Honeywell

Honeywell CM721 user manual

Carrier

Carrier DEBONAIR 33CS Installation and operating instructions

Lennox

Lennox iHarmony Zone Thermostat Installation and setup guide

Gemtech

Gemtech GT7000 Operation

Rollei

Rollei Smartes 45000 manual

Sinope

Sinope TH1300RF user guide

Honeywell

Honeywell RLV4305 owner's guide

Honeywell

Honeywell Prestige 2.0 THX9421 manual

NuTone

NuTone NTBZ48 Installation & operation guide

Stelpro

Stelpro MAESTRO ASMT402AD user guide