Danfoss AME 110 NL User manual

VD.KH.C6.02 © Danfoss 01/2014

SMT/SI

Actuators for modulating control

AME 110 NL, AME 120 NL

Data sheet

Description The actuators are used together with

automatically balanced combination valve type

AB-QM for DN 10-32.

The actuator can be used with fan coil units,

induction units, small reheaters, recoolers and

zone applications in which hot/cold water is the

controlled medium.

Main data:

• Gapdetectionatstemupposition

• Modulatingcontrol

• Forceswitch-oatstemdownposition

prevents overload of actuator and valve

• Notoolsrequiredformounting

• Maintenance-freelifetime

• Low-noiseoperation

• Self-positioningprocess

• Halogenfreecables

Ordering Type Supply voltage Speed Cable length Code No,

(V) (s/mm) (m) SinglePack IndustryPack

AME110NL

24 AC

1,5 082H8057 082H8067

5,0 082H8081 082H8077

10 082H8098 082H8087

AME120NL 12

1,5 082H8059 /

5,0 /082H8079

10 /082H8089

Note:

Actuators with 5 m and 10 m cable length are produced on request. Please note this increases lead time.

Spare parts

Type Length Code No.

(m)

Cable (24 V) 5082H8052

10 082H8054

2VD.KH.C6.02 © Danfoss 01/2014 SMT/SI

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

Technical data

Type AME 110 NL AME 120 NL

Powersupply V 24 AC; +20 to −15% *

Powerconsumption running VA 2

standby W0,5

Frequency Hz 50/60

Control input Y V0-10(2-10)Ri=110kΩ

mA 0-20(4-20)Ri=500Ω

Closing force N130

Stroke mm 5

Speed s/mm 24 12

Relative humidity max. 80 %

Max. medium temperature

°C

120

Ambient temperature 0 … 55

Storageandtransporttemperature –40 … 70

Protectionclass III safety extra-low voltage

Gradeofenclosure IP42

Weight kg 0,3

-markinginaccordancewith

standards

LowVoltageDirective2006/95/EC:EN60730-1,EN60730-2-14

EMCDirective2004/108/EEC:EN61000-6-2,EN61000-6-3

* 24V AC; +10% to −15% if produced before w18y2013

Installation Mechanical

The actuator should be mounted with the valve

stem in either horizontal position or pointing

upwards.

The actuator is ﬁxed to the valve body by means

ofamountingring,whichrequiresnotoolsfor

mounting. The ring should be tightened by hand.

Electrical

Important: It is strongly recommended that the

mechanical installation is completed before the

electrical installation.

Auto sleep mode

1. IfactuatorAME110NLischargedby24V

supply voltage and if it is not installed on

AB-QM valve, it will stop in lower position and

switchoallLEDindicatorsafter5minutes

2. It is mandatory to drive the spindle of the

actuator to upper position before it will be

installed on AB-QM valve (please refer to

manual override drawings)!

3. Autosleepmodeswitchesbacktolearning

modebypressingRESETbuttonorbycycling

power supply

Each actuator is supplied with the connecting

cable for the controller.

VD.KH.C6.02 © Danfoss 01/2014

SMT/SI

position

indicator

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

1. Checkthevalveneck.Theactuatorshouldbe

in stem up position (factory setting).

Ensure that the actuator is mounted securely

on the valve body

2. Wire the actuator according to the

wiring diagram

3. The direction of the stem movement can be

observed on the position indicator

Installation procedure

Wiring

Commissioning The factory setting of the spindle is the fully

stem up position because of easier mechanical

connection of the actuator on the valve.

Disposal The actuator must be dismantled and the

elements sorted into various material groups

before disposal.

VD.KH.C6.02 © Danfoss 01/2014

SMT/SI

Reset



Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

DIP Switch Setting

(for service purposes only)

TheactuatorhasafunctionselectionDIPswitch

under the removable cover.

Theswitchprovidesthefollowingfunctions:

• SW1:

U/I - Input signal type selector

 IfsettoOFFposition,voltageinputis

selected. If set to ON position, current input is

selected.

• SW2:

0/2 - Input signal range selector

 IfsettoOFFposition,theinputsignalisin

the range from 2-10 V (voltage input) or from

4-20 mA (current input). If set to ON position,

the input signal is in the range from 0-10

V (voltage input) or from 0-20 mA (current

input).

• SW3:

D/I - Direct or inverse acting selector

 IfsettoOFFposition,theactuatorisdirect

acting (stem contracts as voltage increases). If

the actuator is set to ON position, the actuator

is inverse acting (stem extracts as voltage

increases).

• SW4:

---/Seq - Normal or sequential mode

selector

 IfsettoOFFposition,theactuatorisworking

in the range 0(2)-10 V or 0(4)-20 mA. If set

toONposition,theactuatorisworkingin

sequentialrange;0(2)-5(6)Vor

(0(4-0(12) mA) or (5(6)-10 V) or

(10(12)-20 mA).

• SW5:

0-5/5-10 V - Input signal range in

sequential mode

 IfsettoOFFposition,theactuatorisworking

inthesequentialrange0(2)

5(6) V or

0(4)

10(12) mA.

If set to ON position, the

actuatorisworkinginthesequentialrange;

5(6)-10 V or 10(12)-20 mA.

• SW6:

LIN/LOG - Linear or equal percentage ﬂow

through valve selector

If set to ON position, the ﬂow through the

valveisequalpercentage-wiseequalsthe

controlsignal.IfsettoOFFposition,thevalve

position is linear acc. to the control signal.

• SW7:

---/ASTK

- Anti-blocking function

 Exercisesthevalvetoavoidblockingin

periodswhentheheating/coolingiso.

 IfsettoONposition(ASTK),thevalvemotion

is switched on. The actuator opens and closes

the valve every 7 days.

 IfsettoOFFposition(---),thefunctionis

disabled.

• SW8:

Reset switch and reset button on PCB

Changing this switch position will cause the

actuatortogothroughaselfstrokingcycle.

Note: Reset switch and reset button on

PCBhave the same function. The reset

switchmustbeinOFFpositiontomake

reset

button function active ( press it for 2 sec. ).

Remark:

Factory setting: All switches (except switch 2 which is in ON position) are in OFF positions.



0-10

INV

SEQ

5-10

LOG

ASTX

RESET

OFF

2-10

DIR

---

0-5

LIN

---

RESET

VD.KH.C6.02 © Danfoss 01/2014

SMT/SI

⑤

①

②

③④

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

• Removecover①

• Pressandholdthebutton②(on the

bottom side of the actuator) during manual

override ③

• Replacecover④

• Installactuatoronvalve⑤

Remark:

A‘click’soundafterenergisingtheactuator

indicates that the gear wheel has jumped into

normal position.

If manual override has been used, the Y

signal will not be correct until the actuator

has reached its end position. If this is not

acceptable, reset the actuator.

Manual override

(for service purposes only)

Caution:

Do not manually operate the

drive if power is connected!

Do not dismount the actuator

from the valve when it is in a

stem down position!

If dismounted in a stem down

position,thereisahighrisk

thattheactuatorgetsstuck.

Dimensions (mm)

6VD.KH.C6.02 © Danfoss 01/2014 SMT/SI

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

VD.KH.C6.02 © Danfoss 01/2014

SMT/SI

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

8VD.KH.C6.02 Produced by Danfoss A/S © 01/2014

Data sheet Actuators for modulating control AME 110 NL, AME 120 NL

Other manuals for AME 110 NL

This manual suits for next models

Table of contents

Other Danfoss Controllers manuals

Danfoss

Danfoss VLT AutomationDrive FC 302 User manual

Danfoss

Danfoss 51 Series User manual

Danfoss

Danfoss EFIT 850 User manual

Danfoss

Danfoss EKC 202A User manual

Danfoss

Danfoss ECL Comfort 210 User manual

Danfoss

Danfoss EET Series User manual

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 User manual

Danfoss

Danfoss AME 855 User manual

Danfoss

Danfoss A333 Series Installation instructions manual

Danfoss

Danfoss AME 655 User manual

Danfoss

Danfoss OBC 80 Series User manual

Danfoss

Danfoss VLT MCD 600 User manual

Danfoss

Danfoss AMV213 User manual

Danfoss

Danfoss A377.1 Installation instructions manual

Danfoss

Danfoss AK-PC 420 User manual

Danfoss

Danfoss 101N0715 User manual

Danfoss

Danfoss 101N0715 User manual

Danfoss

Danfoss ECL Comfort 110 User manual

Danfoss

Danfoss MCD Series User manual

Danfoss

Danfoss NovoCon Series User manual

Danfoss

Danfoss AK-CC55 User manual

Danfoss

Danfoss AME 55QM User manual

Danfoss

Danfoss PCVA User manual

Danfoss

Danfoss ECL 2000 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual