Dancing Wings OLD FOGEY User manual
DW OLD FOGEY INSTALLATION INSTRUCTIONS
Accessories include
Specification
Wingspan: 1150mm
Length: 720mm
Flying Weight≈780g
Suggested Equipment
Battery：3s 1500-2200mAh
Motor：2830 1150KV
Propeller:9-10inch
ESC: 20A
Servos：9g*4
Radio≥4CH
Preparation Tool
Fuselage
Horizontal Tail
Wing
Propeller
Bolt
Y-wire
Rubber band
Prop Adapter
ESC
Motor
Screws
Foam glue
OLD FOGEY
EPP
Trainer airplane for out-door ying
A
B
C
D
E
F
G
H
I
J
J1
K
L
M
N
O
P
Q
R
S
T
U
W
X
Servo
Back landing gear pieces
Back landing gear wheels
Servo horns
Servo connecting rod (short)
Servo connecting rod (long)
Landing gear rod
Rubber tube for wheel fixation
Wing Fiberglass Reinforcement
Front landing gear wheels
Vertical Tail
Hinge
DW OLD FOGEY INSTALLATION INSTRUCTIONS
0.01 Apply the glue on the side of the wing, and
join together, and then insert the fiberglass rein-
forcement into the slot on wing.
0.02 Assemble another wing by the same above way.
0.03 Insert the servo into the slot on the back of the
wing, meantime insert and glue the servo wire into
the wing; Assemble the another servo by same way.
0.04 Make a cut by knife in an upright position with
servo, insert the hinges and fix by glue. Connect
the servo and servo horns on aileron by steel wire.
Assemble the other by same way.
0.05 Insert the horizontal tail into the rear of the
fuselage, and fix by glue.
0.06 Apply the glue on the side of the vertical tail,
adjust and maintain the level with fuselage, finally
join together by hinge and glue.
How to Assemble
Servo
Back landing gear pieces
Back landing gear wheels
Servo horns
Servo connecting rod (short)
Servo connecting rod (long)
Landing gear rod
Rubber tube for wheel fixation
Wing Fiberglass Reinforcement
Front landing gear wheels
Vertical Tail
Hinge
DW OLD FOGEY INSTALLATION INSTRUCTIONS
0.07 Glue the back landing gear pieces and punch
holes on the wooden board as per the wheel screw
holes; finally assemble the back landing gear as
picture shows.
0.08 Assemble the servos into the servo slots inside
the fuselage and fix with screws.
0.09 Insert the servo steel wires into the slot on the
fuselage, one at either side of the fuselage. Confirm
the position of the steel wire comes out, make cuts
on the horizontal and vertical wing by knife, insert
the servo horns and fix by glue. Connect the EZ
connector with steel wire, and then connect the EZ
connector with servo horns.
0.10 Connect the other end of the steel wire with
servos.
0.11 Insert the front landing gear rods into the hole
reserved for landing gear on the leading edge,
assemble the front landing gear wheels and fix with
rubber tube.
Drilling
DW OLD FOGEY INSTALLATION INSTRUCTIONS
0.12 Insert the motor wires into the holes reserved
for motors, and then fix with screws on the head
0.13 Connect the ESC with motor.
0.15 Put the battery and receiver into the fuselage,
adjust the plane CG, then start your first test flight.
0.14 Insert the wing bolts into the two holes on the
upper part of the fuselage, and then fix with rubber
band as picture shows.
J1 Screws
CG
Other Dancing Wings Toy manuals
Dancing Wings
Dancing Wings DW MINI EAGLE User manual
Dancing Wings
Dancing Wings DW DANCING POKE User manual
Dancing Wings
Dancing Wings DW PTERODACTYL User manual
Dancing Wings
Dancing Wings SCG42 User manual
Dancing Wings
Dancing Wings LIGHTING EPP User manual
Dancing Wings
Dancing Wings DW DANCING PITTS User manual
