Daewoo DW-3610 User manual

NAME OF PARTS

(

)

! Wash Timer

@ Select Switch

# Water Inlet Port

$ Washer Lid

% Washer Tub

Accessories

7 Spin Mat

^ Strainer

& Pulsator

* Valve Selector

( Spin Dryer Timer

) Spin Dryer Lid

8 Drain Hose Assembly

1 Inner Lid

2 Overflow Filter

3 Spin Dryer Drum

4 Base Under

5 Power Cord

6 Leg (4EA)

INSTALLATION

Electrical Connection

• This unit is designed to operate from an adequate supply mentioned at the

rating label sticked to the rear of it.

• In case of 3-core cord: The power cord plug must be connected to an earthed

3-pin power point within reach of the power cord.

• In case of 2 conductor power cord: Connect the grounding wire to a water fau-

cet etc. Make sure that the power cord is unplugged during ground work.

• Do not connect the grounding wire end to a gas tube.

• If the power cord is damaged, it should be replaced by a repair shop appointed

by the manufacturer, because special purpose tools are required.

Connection of Hose

• Attach the water intake hose to the

Water inlet located at the left-hand

side of the con-trol panel. Press fit the

other end of the hose to either a hot

or cold water tap as required. (Fig. 1).

• Attach the drain hose to the drain out-

let at the rear of the base and secure

with the clamp provided.

• The drain hose should be laid flat on the ground. Water flow will be restricted

if any portion of the drain hose is raised 20 cm (8 in) from the ground.

• The opening must not be obstructed by carpeting when the washing machine

is installed on a carpeted floor.

WATER INTAKE HOSE

WATER INLET

Figura 1.

Caution: This unit is made of poly

propylene, use water below 50°C.

HOW TO OPERATE

1. Wash

§Insert the power plug into a wall

socket.

§Set the selector at WASH AND

RINSE, and fill up the washer with

enough water for the washing load.

§Put in the proper amount of detergent.

Pre-washing takes about 2 minutes and is immediately followed by the main

washing process.

Delicate fabric such as silk, wool do not need prewashing.

Divide colored and white clothing into seperate batches.

§Depress one of the select switches

for SOFT or NORMAL washing.

§Turn the washer timer to clockwise until you reach the desired wash time

position. This will activate the pulsator and washing will begin.

Do not attempt to turn the dial from “OFF” to the left, nor past the “15” mark.

WASH RINSE

DRAIN

WASH AND

RINSE

NORMAL

BOTH-WAY

SOFT

BOTH-WAY

SELECTOR

SWITCH

Socket Plug

Power cord

After using the machine, unplug the

power cord from the socket.

Reference

Water

Washing Fabric Washing Selector level & Detergent

Capacity Time Switch Volume

(Inner clothing)

Silk, Wool, Rayon, Nylon About Soft

Natural/Synthetic fiber 2-4min

blends (Outer garments)

Cotton, Linen (light fabric) About Normal Low 40-50 g

Underwear Pajamas, Shirts 5-7 min 31 L

Heavily solied work About Normal

clothes, Cotton, Linens 8-10 min

(heavy fabric)

Silk, Wool, Nylon, Natural/ About

Synthetic fiber blends 2-4 min Normal

(heavy fabric)

Cotton, Linens About Normal

6-8 min

Heavily Solied About High 55-65 g

Work Clothes 10 min Normal 43 L

Cotton, Linens

Below

1.5 kg

Above

1.5 kg

Item Fabric Unit weight

Sheet Cotton About 400g

Under wear Crape About 130g

Shirts Synthetic fiber About 200g

Sweater Wool About 300g

White shirt Broad About 200g

White shirt Nylon About 160g

Work clothes Cotton About 600g

2. Drain

By setting the selector DRAIN, the water

will drain out of the washer. To spin dry

and drain at the same time, first begin

the spin drying process and after one

minute or so start to drain out the water.

3. Spin Dry 1

(1) Spread out the clothes and place

them one at time into the spin

basket.

(2) Close the spin dryer inner cover and

outer cover.

Remember that the machine will not

spin if the cover is opened.

(3) By turning the spin dryer timer to the

desired time, rotation will begin.

(4) If there is any abnormal vibrating

during spin drying, turn off the spin

basket and rearrange the clothes

uniformly inside the dry.

WASH RINSE

VALVE SELECTOR

DRAIN DRAIN

open outer lid open inner lid

SPIN TIMER

stops

NOTE:

It is advisable to wiring out by hand any remaining suds in the cloth-

ing before placing them in the spin basket.

If the spin dry outer lid is opened during spin drying rotation will

automatically stop.

CAUTION

Make sure that the spin basket has stopped

rotating before opening the inner cover.

Never reach into spin basket while it is

still in motion.

Be especially careful when children are

present.

4. Rinse

§Return the clothing to the washer tub and set the selector to WASH AND

RINSE.

§Open the faucet and supply water to the washer tub.

Too mush water supplying during rinsing results in overflow and waste. Not

enough water requires an excessive amount of time for through rinsing.

Supply the proper amount of rinse water.

§Adjust the washer timer in accordance with

the clothes to be rinsed.

Once the water becomes clean during the

rinsing process, shut off the faucet and turn

the washer time back to “0”.

5. Spin Dry 2

§After rinsing, spin dry the clothes again.

§Supply water to the dryer to make sure that is completely free of any remain-

ing detergent before putting in the clothes.

Then follow the same process as in SPIN DRY.

After the dryer comes to a complete stop remove the clothing.

WASH TIMER

NOTE:

It is better to put small articles of clothing first such as socks and underwear

into the spin basket, then put bulky and heavy clothing on top.

Clothing Spin dryer time

Clothing that wrinkless easily

Light fabrics such as synthetics fibers, delicate About 1 minute

material.

Clothing that does not wrinkless easily Workclothes, 3-5 minutes

Sheets, Underwear, thick fabric

USEFUL INFORMATION FOR YOU

WASHING MACHINE

To ensure longer service from your washer, be sure to observe the

following instructions.

§Never operate the washer until the water has risen to a pre-set level.

§Never pour boiling water directly into the washer tub.

§The color of the plastic portions of the machine is liable to fade and may even

be deformed through exposure to direct sunlight.

§The drain hose should be laid flat on

the ground. Water flow will be res-

tricted if any portion of the drain

hose is raised more than 20cm (8 in)

from the ground.

§Do not use the washer in a damp place such as a bathroom.

§Keep the spin tub cover closed during operation. If the cover is opened the

spin basket will stop rotating.

§Do not splash water on the control

panel.

§For good air ventilation, install the washer at least 5 cm from the wall.

§Be sure to use the proper electrical outlet.

§The overflow filter will need occasional cleaning.

Grasp it at the upper and pull out to remove it. Then, after cleaning out thread

and other matter, replace the filter inserting, its bottom section and then pushing

the upper part firmly into place.

Below

20 cm

Dirt may also collect underneath the pulsator.

Clean out occasionally by:

§Remove the screw located in the center of the pulsator.

§Hook the pulsator and pull upwards.

§Wiping clean the bottom of the

washer tub.

(When replacing the pulsator, make

sure that screw is firmly tightened)

When opening and closing the inner lid, make sure to pull it toward you.

CAUTION: For your safety, do not put your hands into spin basket until it

has stopped spinning completely.

IN CASE OF TROUBLE

Please check the following. Unplug the power cord from the socket

before checking.

1. If the washer will not start:

§Check whether the house circuit breaker is tripped or a fuse is blown.

Check whether the power cord is connected to the socket properly.

Check whether something is preventing the pulsator from rotation.

Check whether the belt is attached properly.

(Check by removing rear cover0

2. If there is excessive noise:

§Check whether something is touching the pulsator as rotates.

Check whether the machine is placed level on the floor.

Check whether there is an excessively unbalanced load in the spin basket while

spinning.

CAUTION: After installing, DO NOT REMOVE LEGS.

HOW TO FIX LEG TO BASE-HOLE FOR

INSTALLATION

• When you install this unit, be sure to

assemble LEGS(4EA) to base

under(Fig.4).

• Place this unit on its rear side on a

carton to prevent damage to the body.

• Insert the leg(4EA) into the base

under hole as it was. By first inserting

its two hooks.

• Turn right and screw on leg.

• Make the allows of leg and base

under face with each other at each

corner.

HOOK (2EA)

1. Inserting

2. Turn right

3. Screw on.

Figure 4.

WASHER-SPINDRYER

INSTRUCTION MANUAL

Model No.: DW-3610

§Thank you for selecting this washer-spindryer.

§Before operating this unit, please read these instructions completely.

Other manuals for DW-3610

Table of contents

Other Daewoo Washer manuals

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual