Daewoo DWC-055RL User manual

MODEL #: DWC-055RL

DWC-063RL

ROOM AIR CONDITIONER

USE & CARE MANUAL

WINDOW TYPE ROOM AIR CONDITIONER

CUS

LISTED

UL and

CUL listed

Please read carefully and thoroughly this manual before

operating the unit.

If you still have any difficulties or problems, consult your

dealer for help or ELECTRONICS.

Please keep this manual well.

S/N : 3113905610

Please observe the following instructions.

1. Operate the Selector Switch to run or stop the unit.

- Do not use Main Power Switch or Auxiliary Power Switch to operate unit.

2. Do not stick anything into the air outlet or inlet.

- It is dangerous and it can cause injury or damage.

3. Avoid exposing your body directly to a continuous cool air - flow for long periods.

- It is not good for your health.

4. Do not pour water on the unit to clean it.

- It is dangerous and it can cause injury or damage.

Never use solvents or harsh chemicals when cleaning the unit.

When the air inlet grill and cabinet are dirty, wipe with luke - warm water (below 104°F or 40°C)

5. Avoid placing any obstacles near the inlet or outlet.

- If the inlet or outlet is blocked with any obstacle, it may cause damage to the unit.

6. Do not run or stop the unit frequently.

- If you run or stop the unit more then 4-5 times an hour, it can cause damage to the unit.

7. Wait at least 3 minutes before restarting the unit or in the case of power failure.

- If you turn on the unit within 3 minutes after power off, this can cause damage to the unit.

8. If the air conditioner is operated without an air filter, dust is not removed from the air, and resultant

accumulation in the unit may lead to a failure.

- Do not forget to install the air filter.

9. The air filter should be cleaned at least once every two weeks.

10. When the unit is cleaned, set the Selector Switch at off position.

- And then unplug the power plug.

11. Never store gasoline or other flammable liquid near the air conditioner.

- It is very dangerous.

12. Do not force the controls on the front panel too much.

- It can cause damage the controls and the unit.

13. Set a comfortable temperature.

- Very low temperature setting considerably increase power consumption.

14. Be careful to keep room temperature comfortable.

- Avoid continuous direct air flow on you or a sick person while sleeping.

15. Do not remove the plug by pulling the power cord.

- Damage to the cord and may cause shock hazard

PRECAUTIONS FOR PROPER USE OF AIR CONDITIONER

GENERAL SPECIFICATIONS

ITEM MODEL

POWER SOURCE

DIMENSIONS

WEIGHT (NET)

DWC-055RL / DWC-063RL

AC 115V, 60Hz, SINGLE PHASE

17.3(W) x 12.3(H) x 15.2(D) inch

440(W) x 313(H) x 385(D) mm

45.4 Ibs (20.6 Kg)-Approx.

1. GENERAL SPECIFICATIONS...............................................................................2

2. INSTALLATION INSTRUCTIONS.......................................................................3~7

• WINDOW REQUIREMENTS

• BASIC TOOLS NEEDED

• SAFETY INSTRUCTIONS

• STEP1-PREPARE COMPONENTS FOR INSTALLATION

• STEP2-PREPARE WINDOW FOR INSTALLATION

• STEP3-PLACING UNIT IN WINDOW

• STEP4- INSTALL SASH BRACKET

• STEP5-SECURE WINDOW SHUTTER

• STEP6-RECHECK INSTALLATION

• STEP7-RECHECK THE ENTIRE INSTALLATION

3. NAMES OF MAJOR COMPONENTS .....................................................................8

4. OPERATION INSTRUCTIONS.........................................................................9~14

• DISPLAY

• REMOTE CONTROL

• HOW TO INSERT BATTERIES

5. GENERAL INFORMATION.................................................................................15

• CHANGING AIR FLOW DIRECTION

• AIR FLOW AROUND UNIT

6. CARE AND MAINTENANCE ..............................................................................16

• AIR FILTER

• CLEANING THE AIR CONDITIONER

7. ELECTRICAL REQUIREMENTS .........................................................................17

• ELECTRICAL GROUNDING INSTRUCTIONS.

• USAGE OF POWER CORD(AFCI & LCDI)

8. BEFORE CALLING FOR SERVICE......................................................................18

TABLE OF CONTENTS

INSTALLATION INSTRUCTIONS

• WINDOW REQUIREMENTS

These instructions are provided for a standard double hung

window or mobile home double hung window installation in

windows 21.7in (550mm) to 34.6in (880mm). The upper and lower

sash must open sufficiently to allow a clear vertical opening of

12.7in (323mm) from the bottom of the sash to the window stool.

Select a centrally located window on the side of the room that

receives the least direct sunlight. There should be no obstruction to

air flow either inside(i.e curtains) or outside (i.e fence, wall or

bushes).

Read this entire installation manual thoroughly before beginning

the installation.

Make sure you have the necessary tools and other materials for the job. Study the illustrations in these

instructions to become familiar with important details of the installation process.

Read the Use & Care manual to become familiar with the operation of your room air conditioner.

After installing the unit, re-read these instructions to make sure you have completed each step and all parts are

fastened in place for a secure installation.

For best results, perform the installation procedure in the order given. Doing so will minimize the time required

to install the unit.

• BASIC TOOLS NEEDED

IMPORTANT :

It is important, both for your personal safety and to avoid possible damage to your home, that you observe

the safety instructions that are given following.

• Standard screwdriver

• Carpenter’s level

• Electric drill

• Phillips screwdriver

• 1/4”hex driver

• 1/8”drill bit

• Sharp knife

• Tape measure

22" TO 36"

14 1/2" MIN

21.7”TO 34.6”

12.7”MIN

• SAFETY INSTRUCTIONS

The receptacle should be an individual branch circuit used only for this air conditioner. Be sure the electrical

service is adequate for the model air conditioner you have chosen. The complete electrical rating of your air

conditioner is stated on the name plate located at the unit’s side. Be sure the plug receptacle is close enough

for the power cord to reach it.

Your air conditioner must be plugged into a properly grounded and polarzied three prong receptacle. Do not

use an adapter plug. If the wall receptacle you intend to use will not accept a three-prong plug, or if you are not

sure the outlet is adequately grounded or protected by a fuse or circuit breaker, have a qualified electrician

install the proper oulet according to the National Electric Code and applicable local code.

WARNING :

An extension cord should not be used with your air conditioner!

To minimize shock and fire hazards, proper grounding is important. For your safety and

protection,this air conditioner is equipped with a special three-prong grounding plug on the service cord.

WARNING :

A cord-connected room air-conditioner shall be marked to indicate that a damaged power supply cord must

be replaced with a new power supply cord obtained from the store where you have purchased your air-

conditioner or SVC center which the store instructs you.

WARNING :

Do not, under any circumstances, cut or remove the grounding prong on the plug. To do so will create a shock hazard.

• Step 1 - Prepare Components For Installation

1. Open the components box for installation

2. Check components for installation as follows.

•Sill Bracket (1 piece)

•Window Shutter (2 pieces)

•Sash Bracket (1 piece)

•Window Kit Frame - Left side (1 piece)

•Window Kit Frame - Right side (1 piece)

•Leveling Screw - M8 x 45 (1 piece)

•

11/4

inch Screw - M5 x 30 (2 pieces)

•5/8 inch Screw - M4 x 16 (5 pieces)

•5/16 inch Screw - M4 x 8 (6 pieces)

•Window Seal A, B (2 pieces)

• Step 2 - Prepare Window For Installation

1. Inspect window track, sash and sill to be sure they are strong enough to hold an air conditioner.

2. Measure width between window frame to be sure instant mount will fit in the window. Instant mount models

are designed for windows 21.7in (550mm) to 34.6in (880mm) wide.

3. Mark the center of window sill with a pencil.

4. Insert Screw (Type A) into the sill bracket.

5. Attach Sill bracket to window sill using Screws (Type B).

(The outside edge of window bracket should be center line)

6. Place the carpenter’s level on the sill and the outdoor end of Sill Bracket.

Adjust Screw (Type A) so that Sill Bracket have a slight tilt by using

carpenter's level meter. (about 1.5°)

WARNING :

1.To reduce the risk of electric shock, personal injury or death, turn the fan control to the OFF position

and unplug the unit from the wall outlet before installing or removing this unit.

2.The window where the air conditioner is to be installed should have enough strength to bear the

weight of the air conditioner.

OUTER

WINDOW

SILL

CENTER

LINE

INNER WINDOW SILL

SILL

BRACKET

Screw (Type B)

Screw (Type A)

INNER

WINDOW

SILL

OUTER

WINDOW

SILL

BRACKET

about 1.5°

UNIT

SILL

BRACKET

0.28"~0.39"(7~10mm)

SHAPE

SPEC

Q'TY

Type A

M8 x 45

Type B

M5 x 30

Type C

M4 x 16

Type D

M4 x 8

•SCREW TYPE

Window

Shutter

(2 pieces)

Window Seal A (1 piece)

Window Seal B (1 piece)

Sill Bracket (1 piece) Window kit Frame

Left side (1 piece) Window kit Frame

Right side (1 piece)

Sash Bracket

(1 piece)

•Step 3 - Placing Unit in Window

1. Insert Window Kit Frame into the upper and bottom guides of the unit.

2. Fasten window shutter in the window kit frame with Screws (Type D) in the left side and right side of the unit.

3. Open the window and place the unit in the center of the window sill.

•Step 4 - Install Sash Bracket

Fasten Sash Bracket with Screw (Type C) to top of indoor

window sash or directly into side of window sash or directly

into side of window frame.

This will prevent the raising of the window from the outside. If

you have a hard wood or metal window frame, a 1/8 inch pilot

hole may be needed in order to drive the screw.

CAUTION

1. The unit is heavy. To avoid injury or accident, it is strongly recommended that you have additional

help when lifting the unit.

2. Personal injury or property damage may result if unit falls from window.

CAUTION

Do not drill into window frame until window has been inspected to make sure drilling or screw will

not damage any locking or lifting mechanism located the frame.

WINDOW

FRAME

Screw (Type C)

SASH

BRACKET

WINDOW

SASH

WINDOW

SHUTTER

(bottom guides)

WINDOW

KIT

FRAME

PLATE

WINDOW

TOP

(upper guides)

Screw

(Type D)

•Step 5 - Secure Window Shutter

To provide a proper seal, pull each expandable side Window Shutter out

and up until it is tight against the window frame. Using the hole in the top

and bottom of each Window Kit Frame as a guide, secure Window Kit

Frame in window sash and on the window sill.

•Step 6 - Recheck Installation

To be sure you have correctly installed your Room Air Conditioner, review the steps and make sure all of the

parts are securely fastened in the window as the instructions show. A tight seal is essential.

Read through the Use & Care manual to become familiar with the operation of your room air conditioner.

•Step 7 - Recheck the Entire Installation

CAUTION

Do not drill into window sash until window has been inspected to make sure drilling or

screw will not damage any locking or lifting mechanism located in the frame.

CAUTION

Do not lift window sash without holding the unit. The window sash helps keep the unit in the window.

Exercise caution when opening the window. Failure to do so many result in personal injury and/or

property damage.

WINDOW

SHUTTER

WINDOW

KIT FRAME

Screw (Type C)

INNER WINDOW SILL

WINDOW

SASH

WINDOW

FRAME

WALL

Screw (Type B, 2 pieces)

SILL

Screw (Type C, 2 pieces)

GUIDE LOWER

WINDOW KIT 'R & 'L

Screw (Type D, 2x3=6 pieces)

Screw (Type C, 2 pieces)

WINDOW SEAL A

WINDOW SASH

SILL BRACKET(1 piece)

OUTER WINDOW SILL

Leveling Screw (Type A, 1 piece)

TOP GUIDE

WINDOW KIT FRAME

WINDOW SEAL B

0.28"~0.39"(7~10mm)

NO PART NAME

1 CABINET

2 BLADE VERTICAL

3 COOL AIR DISCHARGE

4 GRILLE FRONT

5 PANEL CONTROL

6 AIR INTAKE

NO PART NAME

7 AIR FILTER

8 FRAME GUIDE TOP

9 FRAME WINDOW KIT

10 SHUTTER WINDOW

11 REMOTE CONTROLLER

NAMES OF MAJOR COMPONENTS

•DISPLAY

OPERATION INSTRUCTIONS

TEMP./TIMER DISPLAY

•It displays the

temperature and the

timer.

MODE DISPLAY

•It displays the operating mode.

REMOTE SIGNAL

RECEIVER TEMPERATURE SET

•It is the button to set the desired

room temperature.

The temperature can be set

within a range from 16°C (60°F)

to 32°C (90°F) by 1°C (1°F)

POWER ON/OFF SWITCH

•To turn the unit ON, push this button.

To turn the unit OFF, push this button

again.

MODE SELECT

•Everytime you push this button, It is selected as

follow. (COOLING→TURBO→FAN→COOLING)

FAN SPEED

•Everytime you push this button, It is selected as

follow. (Low→High→Low)

ENERGY SAVE

•Whenever you push this button, the cumulative power

consumption is decreased.

CAUTION

When you turn off the unit with cooling mode, the Fan Still work for about 10 seconds.

This manual suits for next models

Table of contents

Other Daewoo Air Conditioner manuals

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual