Da-Lite Curved Multi Format Imager User manual

INSTRUCTION BOOK FOR

Curved Multi Format Imager

Tools Required for Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before

using equipment.

2. Close supervision is necessary when any appliance

is used by or near children. Do not leave appliance

unattended while in use.

3. Care must be taken as burns can occur from touching

hot parts.

4. Do not operate appliance if it has been dropped or damaged

until it has been examined by a qualiied service technician.

5. To reduce the risk of electric shock, do not immerse this

appliance in water or other liquids.

6. The use of an accessory attachment not recommended

by the manufacturer may cause risk of ire, electric shock

or injury to persons.

Pre-Installation

The screen will arrive in three separate cardboard boxes. One

box will be very long and will house the 4.75” x 8.00” top and

bottom main frame parts, the 1.50” x 1.50” frame parts, hardware

and wall switch. The second cardboard box will house the 4.75” x

8.00” side main frame parts. The third cardboard box will house

the fabric for the Curved Da-Snap Screen.

Have space for this available on a lat clean surface such a large

table or loor. The work area should be larger than the frame size.

If the loor is used, clean papers should be spread to keep all dirt

from the screen surfaces. Do not use newspaper..

Phillips Screwdriver

1/8” Allen Wrench

1. Inside each box the frame pieces will be individually paper

wrapped and taped. Remove all paper from pieces.

Do not use a utility knife to remove paper from pieces.

2. Unpack the 1.50” x 1.50” frame parts and fabric from the

cardboard boxes. DO NOT unroll the screen surface

at this time.

3. Slide the frame pieces together at corners. Secure frame

pieces with #10 black screws provided. Do not tighten screws

until all are started, and then tighten (Figure 1).

NOTE: The frame pieces are labeled “TOP” and “BOTTOM”. Be

sure the frame pieces are assembled according to the labels.

This will ensure the snap pattern on the frame and screen

surface will match.

4. Unroll the screen on a clean surface. Do not use newspaper.

Place screen surface over the frame, and while holding the

frame with one hand, snap the screen surface onto the frame

with the other hand while maintaining a steady pull on

the surface. Start with the four corners.

5. Set assembly aside; it will be attached to the main frame.

Da-Snap Frame Assembly

Side

Corner

To p

Snap Stud

#10 Black Screw

Bottom

Figure 1 (Front View)

Curved Multi Format Imager Assembly

1. Lay frame pieces out on the loor or table as shown in Figure

2. The bottom frame assembly has the junction box attached

to it. The side frame assemblies have the rollers and motors

attached to them.

2. Assemble left side of frame to the top of frame (NOTE: Figure

2 is looking from the back of frame). The large L-bracket will

slide into the aluminum extrusion while the small L-bracket

will slide into the frame channel. When sliding the bracket

into the top frame assembly, guide the slat roller carriage into

the top aluminum guide track as shown in Figure 3.

3. Fasten (3) #10 x 3/8” button head screws through top of frame

into the large L-bracket. Tighten two screws on lat small

L-bracket to line up the front surfaces as shown in Figure 4.

Figure 2

Figure 3 Figure 4

Junction Box

Frame Channel

Large LBracket

Small LBracket

Aluminum

Guide Track

Right Frame

Assembly

Bottom Frame

Assembly

Left Frame

Assembly

Make Sure Carriage

Rollers Are Seated

Properly in Guide Track

Fasten Screws

Through Top Frame

Assembly Into

Large LBracket

Tighten Screws

Until Front

Surfaces Are Flush

Slat Roller

Carriage

Top Frame Assembly

4. Assemble bottom end of left frame assembly to end of

bottom frame assembly. The large L-bracket will slide into the

aluminum extrusion while the small L-bracket will slide into

the frame channel. When sliding the bracket into the bottom

frame assembly, guide the slat roller carriage into the bottom

aluminum guide track. See Figure 5.

5. Route the two cable assemblies around motor bracket and

plug the 3 wire male connector into the 3 wire female

connector on the motor bracket. The motor will have a gray

data cable with and RJ45 connector and RJ45 coupler on

the end coming out of the head of the motor. Plug the

connector of the cable assembly into the RJ-coupler. Tuck the

RJ- coupler underneath motor bracket securely to prevent

entanglement as shown in Figure 5.

6. Fasten (3) #10 x 3/8” button head screws through bottom of

frame into the large L-bracket. Tighten two screws on lat

small L-bracket to line up the front surfaces. See Figure 6.

7. Assemble right side of frame to top and bottom frame

assemblies. The two large L-brackets will slide into top and

bottom aluminum extrusion while the two small L-brackets

will slide into the frame channel. When sliding the right side

assembly into the aluminum extrusion, guide the slat roller

carriage into the top and bottom aluminum guide tracks as

shown in Figure 7.

8. Fasten (3) #10 x 3/8” button head screws through top and

bottom of frames into the large L-brackets. Tighten two

screws on each lat small L-bracket to line up the front

surfaces.

Curved Multi Format Imager Assembly

Large

LBracket

Large

LBracket

Small

LBracket

Small LBracket

Aluminum

Guide Track

Frame Channel

Bottom Frame Assembly

Make Sure Carriage

Rollers Are Seated

Properly in Guide Track

Fasten Screws Through Top Frame

Assembly Into Large LBracket

Tighten Screws Until

Front Surfaces Are Flush

Slat Roller

Carriage

Top Frame

Assembly

Figure 7

Aluminum

Guide Track

Plug Motor

Power In

Tuck Excess Wire

Underneath

Motor Bracket

Data Cable From

Motor Head

Tuck RJ45 Coupler

Underneath

Motor Bracket

Plug Connector

Into Coupler

Figure 5

Fasten Screws

Through Bottom

Frame Assembly

Into Large LBracket

Tighten Screws

Until Front

Surfaces Are

Flush

Figure 6

9. Route the two cable assemblies around motor bracket and

plug the 3 wire male connector into the 3 wire female

connector on the motor bracket. The motor will have a gray

data cable with and RJ45 connector and RJ45 coupler

on the end coming out of the head of the motor. Plug the

connector of the cable assembly into the RJ-coupler. Tuck

the RJ45 coupler underneath motor bracket securely to

prevent entanglement as shown in Figure 8.

10. Remove tape from the black steel wire tension cable located

at the bottom left side assembly. Remove wire tie from the

cable assembly. Run black steel wire tension cable down

around pulley at end and bring back towards the end. You

may have to pull slightly hard and clip the tension cable to

the eyebolt secured in the slat bar as shown in Figure 9. Be

careful not to pinch your ingers in the spring. Repeat this

step for bottom right corner of screen.

Note for 192" Wide Screens Only: Move black steel wires

away from the front of the screen over and behind the steel

pin located between the end of the aluminum guide track

and the pinch guard.

11. Remove tape from the black steel wire tension cable located

at the top left side assembly. Remove wire tie from the cable

assembly. This cable assembly will have an extra safety wire

ran through the spring. Run black steel wire tension cable

down around pulley at end and bring back towards the end.

You may have to pull slightly hard and clip the tension cable

to the eyebolt secured in the slat bar as shown in Figure 10.

Be careful not to pinch your ingers in the spring. Repeat this

step for top right corner of screen.

Note for 192" Wide Screens Only: Move black steel wires

away from the front of the screen over and behind the steel

pin located between the end of the aluminum guide track

and the pinch guard.

12. Attach end of safety cable to eyebolt in middle of screen.

Repeat this step for top right corner of screen.

13. Carefully slide the Da-Snap frame inside the main frame as

per Figure 11. First, slide the bottom under the bottom

brackets, then the top, under the top brackets. Lift Da-Snap

frame against the inside top and bottom brackets, align holes

and attach with black knobs.

At this point, preparations are needed to provide electrical power

to unit; see wiring diagrams beginning on page 9.

Curved Multi Format Imager Assembly

Figure 9

Figure 8

Clip Wire Tension

Cable To Eyebolt

Insert Wire Between

Brackets, Lower And

Wrap Around Pulley

Slat Bar

Pinch

Guard

Plug Motor

Power In

Aluminum

Guide Track

Plug Connector

Into Coupler

Data Cable

From Motor Head

Tuck Excess Wire

Underneath

Motor Bracket

Tuck RJ45 Coupler

Underneath Motor

Bracket

Curved Multi Format Imager Assembly

Slat Bar

Safety Cable

Passes Through

Middle of

Spring

Black Knob

(4 or 6 For Top Brackets

Black Knobs

(4 or 6 For

Bottom Brackets

Top Brackets

(4 or 6)

Slide This End of Da-Snap Frame

First, Under Bottom Brackets

Junction Box Cover

Bottom Brackets (4 or 6)

Insert Wire

Between

Brackets, Lower

And Wrap

Around Pulley

Pinch Guard

Clip Wire Tension

Cable To Eyebolt Clip Safety Cable

To Middle Eyebolt

Figure 10

Figure 11

Figure 12

Curved Multi Format Imager Installation – Wall Mount

1. The screen is shipped with one wall hanger board. Two small

brackets are included to hold the frame securely to wall

at the bottom.

2. The wall hanger board must be mounted into at least four

wall studs; it must be horizontally leveled.

3. Secure wall hanger board to wall studs at the desire height.

Drill holes and attach wall hanger board into wall. You

will need about 3” clearance above the top surface of the

board. It is recommended to use a 1/4” x 21/2” lag screw and

1/4" lat washer (not supplied) to fasten the board to wall.

NOTE: the top surface of the wall hanger board will align the

top surface of the screen.

4. This step must be done by a lifting device or enough people

to safely lift the weight of the screen over the wall hanger

board. Lift the screen about 3” over the wall hanger board.

5. Align the wood guide of the board with the metal guide of

the screen. Make sure the sides of the screen are located at

the same distance from the wall.

6. Move the screen until slightly touches the wall and let it come

down slowly until it rests on the metal brackets. There is a lip

on the back of the frame that slides down on the surfaces of

the two metal brackets.

7. Attach two small brackets to the bottom of the frame with

two #10 x 3/8” button head screws. Secure brackets to wall

with two screws (not supplied).

8. Attach two side covers with (6) #10 x 3/8” button head screws.

Metal Bracket

(8) ¼" x 2 ½" Lag Screws And

(8) ¼" Flat Washers on

(4) Wall Studs Minimum

(Lag Screws And Flat

Washers Not Supplied)

Side Cover

Metal Bracket

Black Screw

Small Bottom

Bracket

Metal Guide

Wood Guide

Wall Hanger Board

1. To connect power to unit locate junction box cover on

bottom frame assembly. There will be two black screws

holding the wiring box cover on as shown in Figure 13.

2. Install electrical connections. Make sure to review the

wiring diagram for proper hook up as shown in Figure 14.

NOTE: Must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code

(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70. An appropriate disconnect device shall be provided

as part of the building installation.

NOTE: Be sure the unit is wired to a branch circuit rated no

less than 20A.

Multi Format Imager Wiring Diagram

Left Motor Right Motor

Quick Connect

Motor Plug

RJ45

Coupler

Three Conductor

Power Wire

Quick Connect

Motor Plug

White (Common)

Black (Hot)

8P8C

RJ45 Cable

RJ45

6P6C

RJ22 Cable

From Qaux

To Qeye

Remove Two

Screws Holding

Junction Box Cover

Green

(Ground)

Input 120V / 60Hz

RJ45

Coupler

Figure 14

Figure 13

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

Multi Format Imager Wiring Diagram

Multi Format Imager Operation

Connect IR eye to splitter for screen operation. IR eye shall be

plugged into a QEYE port on the primary splitter as shown in

Figure 15.

The Multi-Format Imager has been preset to ive diferent formats.

The screen can be set to any format by simply pressing the

corresponding button on the remote. Below is a list of each

button function.

IMPORTANT When operating the switch, press and release the

buttons. DO NOT hold the button for more than ive (5) seconds

or the button will be reprogrammed to the current screen

position.

Test installation by carefully running mask surfaces in and out

23 times. Be prepared to stop screen. Standard Duty Cycle:

1 MIN.ON./3 MIN.OFF.

CAUTION! Excessive continuos operation may cause

overheating. If motor overheats do not press on remote

and allow motor to cool for 30 minutes.

4 - Sets format to NTSC (1.33:1)

3 - Sets format to HDTV (1.78:1)

2 - Sets format to Letterbox (1.85:1) format.

1 - Sets format to Cinemascope (2.35:1) format.

OPEN - Sets format to Cinemascope (2.40:1) format.

STOP - Stops the masks at any position when pressed.

<> - Individual control of left and right mask.

Figure 15

IR Eye

Qeye Inputs

6P4C

RJ14 Cable

Primary Splitter

Secondary Splitter

6P6C

RJ22 Cable

From Qaux

To Qeye

NOTES:

1.) 6P6C = 6 Pins 6 Conductor Wire

2.) 6P4C = 6 Pins 4 Conductor Wire

RJ22

RJ14

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Green

Red

Black

White

Blue

STOP

OPEN EXT.

PRESET

FORMATS

ADJUST

MASK

RIGHT

LEFT

Figure 16

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite VERSATOL User manual

Da-Lite

Da-Lite IDEA Screen User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol User manual

Da-Lite

Da-Lite UTB Contour User manual

Da-Lite

Da-Lite ACOUSTICAL IMAGER User manual

Da-Lite

Da-Lite electrol User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite Presenter P-50 User manual

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL User manual

Da-Lite

Da-Lite CINEMA CONTOUR SCREEN User manual

Da-Lite

Da-Lite Tensioned Conference Electrol User manual

Da-Lite

Da-Lite Cinema Contour Screen User manual

Da-Lite

Da-Lite DesIgner Contour Manual User manual

Da-Lite

Da-Lite Deluxe Insta-theater User manual

Da-Lite

Da-Lite TENSIONED COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite Designer Contour® User manual

Da-Lite

Da-Lite IDEA Screen User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL User manual

Da-Lite

Da-Lite ASCENDER ELECTROL User manual

Da-Lite

Da-Lite Whiteboard Mount User manual

Da-Lite

Da-Lite Tensioned Director Electrol User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions