Da-Lite Cosmopolitan Electrol User manual

INSTRUCTION BOOK FOR

Cosmopolitan Electrol

For Sizes Up To 9' x 12'

1. Carefully unpack screen and remove outer wrapping from case.

2. Do not remove black tape or rubber bands from slat pocket.

3. Always handle screen in horizontal position.

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Maximum surrounding air temperature 122°F (50°C).

3. Main disconnect must be incorporated in the ixed wiring in

accordance with the wiring rules.

4. Rated for indoor use only.

5. Use copper rated conductors rated 167°F (75°C) or higher.

6. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualiied persons in

order to avoid hazard.

7. Supplied drive is only intended for use in Da-Lite screen models

Advantage, Contour, and Cosmopolitan.

8. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

9. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

10. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

11. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

12. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

13. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not recommended

by the manufacturer.

Save These Instructions

Pre-Installation

Original Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.

However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide

for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any

kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone

assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.

Fabric Height x Width As Ordered, Up To 9

Feet x 12 Feet

Keyhole For Wall Installation

Overall length A = fabric width + 8".

Length B is the distance between wall mounting holes at back of end

caps and is the fabric width + 6 ½".

Motor End

Installation

⅜" Diameter For

Ceiling Installation

Enclosure Cover

⅞" Diameter Opening

For Electrical Fittings

Picture

Surface

1 ⁄"

⁄"

⅞" Diameter

Knock Out

4 ⁄"

5 ⅞"

6 ⁄"

1 ⁄"

NOTE: Under no circumstances should unit be completely sealed in

recessed installation. Allow access for service. Picture surface

is centered in case. Case extends 4" beyond surface on either end.

Do not attach anything to screen slat rod or bottom fabric pocket.

1. Make sure screen is level. Use a carpenter’s level and plumb

level.

2. Remove tape and rubber bands from slat pocket.

CAUTION! Do not cut wrapping paper or tape with knife or

any sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le papier d'emballage ou le

ruban adhésif avec un couteau ou un outil tranchant. Retirez

à la main.

3. Install electrical hook up that applies to your unit. Make sure to

review your Electrical Installation Checklists and wiring diagrams

(included) for either 120 volt switch, 220/240 volt switch, or low

voltage control.

4. Test installation by running screen up and down a few times.

Be prepared to stop screen. Standard Duty Cycle:

1 MIN. ON / 3 MIN. OFF.

NOTE: Must be installed in accordance with the requirements of the

Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA

C22.1 and the National Electric Code (NEC), NFPA 70.

NOTE: DO NOT clean end caps with any cleaning solution. Use only

damp cloth to clean dust from screen case.

Installation Continued

Installation (continued)

For Wall

Use No. 6 Brackets

To Hang Behind

Beam or Valance

Figure 1

For Ceiling

Screen may be mounted on a wall, suspended from ceiling or

extension brackets. Wall screens must be mounted level and with

the case-back parallel to the wall.

Wall Mounting

1. Select fasteners of proper type for wall or ceiling involved.

2. Insert fasteners through proper openings provided in back side

of end caps. See igure 1.

NOTE: DO NOT over tighten fasteners or damage may occur.

3. Attach screen securely to studding or other solid surface - never

to plaster only.

4. MAKE SURE SCREEN IS MOUNTED LEVEL.

Ceiling Mounting

1. Heavy screw hooks may be installed into wood joists. Other

types of hooks or chain may be used for other ceilings or for

stage installations.

2. Insert hooks or chain through proper openings provided in sides

of end caps. Screen must hang so that lat back of case is

perpendicular to loor.

NOTE: DO NOT hang from the end caps at an angle. See Figure

3. Must be perpendicular to the mounting See Figure 4.

3. MAKE SURE SCREEN IS MOUNTED LEVEL.

90°

Figure 2

Figure 3

Figure 4

120V Wiring Diagram

Side View

Of Switch

And Box

This Switch Cannot Be Used With LVC.

NOTE: A single switch cannot be used to operate more than one

screen. Contact the factory for further information.

Down Black

Black

White

Red

Down

AC Hot

Of

Common

White

Black With

Yellow

Up Red

Rocker

Switch

AC Common

120 V. 60 Hz. 2.5 Max. Amp

Operating Switch

And Plate Furnished

With Screen (SPDT

With Center Of)

In Multiple Control

Installations This

Switch Is Replaced By

The Low Voltage

Control, Operated

From Push Button

Stations.

To Junction Box, Mounted In Screen Case,

In Which Internal Wiring Terminates In

White, Black and Red Leads

Down

White Limit

Switch

Adjustment

Wiring Enclosure Cover

120V Wiring Diagram with Optional Built-In Low Voltage Control

RJ45

Receptacle

RJ22

Output

(QAUX)

RJ22

Inputs

(QEYE)

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Green

Red

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the

BUS terminals on the wall switch to the corresponding BUS

terminals on the splitter board.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

STOP

DOWN

BUS

COM

Power Input 120VAC / 60Hz

Green (Ground)

(Ground–Must be Connected

to Building Ground)

Black

(Hot)

White

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Installation Video

To view a video of this installation,

visit http://youtu.be/t2ZQ9PVAhEg

or use the QR code below.

220V Wiring Diagram - European Switch

NOTE: A single switch cannot be used to operate more than one screen. In multiple control installations this switch is replaced by the low

voltage control, operated from push button stations. Contact the factory for further information.

220V Wiring Diagram - Rocker Switch

To Junction Box, Mounted In Screen Case,

In Which Internal Wiring Terminates In

Black, Brown and Blue Leads

This Switch Cannot Be Used With LVC.

Rear View

of Switch

Black (Up)

Brown (Down)

Blue (Common)

Green & Yellow

(Ground)

Black (Up)

Brown (Down)

Blue (Common)

NOTE: Must be wired to conform to local wiring code.

Blue AC Common

Brown AC Hot

230V AC 50Hz

Green & Yellow (Ground)

Jumper Wire

Green & Yellow

(Ground)

Motor

NOTE: A single switch cannot be used to operate more than one screen. In multiple control installations this switch is replaced by the low

voltage control, operated from push button stations. Contact the factory for further information.

To Junction Box, Mounted In Screen Case,

In Which Internal Wiring Terminates In

Black, Brown and Blue Leads

This Switch Cannot Be Used With LVC.

Rear View of DPDT, With

Center Of, Switch in Box

Black (Up)

Brown (Down)

Blue (Common)

Green & Yellow

(Ground)

Black (Up)

Brown (Down)

Blue (Common)

NOTE: Must be wired to conform to local wiring code.

Blue AC Common

Brown AC Hot

230V AC 50Hz

Green & Yellow (Ground)

Blue

Jumper Wire

Green & Yellow

(Ground)

Motor

Brown

Yellow

Of

Down

220V Wiring Diagram with Optional Built-In Low Voltage Control

RJ45

Receptacle

RJ22

Output

RJ22

Inputs

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Red

Green

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

220V Wiring Diagram with Operation & Limit Adjustment Wall

Switch

3-conductor 2024 gauge wire can be used in place of the supplied

RJ14 cable to connect the wall switch. Connect the BUS terminals on

the wall switch to the corresponding BUS terminals on the splitter

board.

IMPORTANT NOTE: The wall switch is REQUIRED to make any limit

switch adjustments, EVEN if a third party control system is used.

Therefore, it is advised to wire the switch or provide a 3-conductor

connection that is accessible.

STOP

DOWN

BUS

COM

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

220V Wiring Diagram with Optional Built-In Low Voltage Control (continued)

220V Wiring Diagram with European Style Wall Switch

Use 3-conductor 2024 gauge wire for wall switch connections.

IMPORTANT NOTE: The European style wall switch is for operation

only and CANNOT be used to make limit switch adjustments.

Therefore, it is advised to wire the limit adjustment switch or provide

a 3-conductor connection that is accessible.

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

Black (Down)

White (Common)

Red (Up)

Red

Black

White

Inputs

Output

Black (Down)

White (L / Common)

Red (Up)

Push Down on Tab to

Insert Wire

Other manuals for Cosmopolitan Electrol

Table of contents

Other Da-Lite Projection Screen manuals

Da-Lite

Da-Lite C User manual

Da-Lite

Da-Lite DESIGNER CONTOUR MANUAL User manual

Da-Lite

Da-Lite Model C User manual

Da-Lite

Da-Lite Cosmopolitan Electrol User manual

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL User manual

Da-Lite

Da-Lite Deluxe Insta-Theater User manual

Da-Lite

Da-Lite ViewShare Advantage Electrol Retrofit User manual

Da-Lite

Da-Lite senIor electrol User manual

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite Boardroom ElEctrol User manual

Da-Lite

Da-Lite HORIZON ELECTROL User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Da-Lite

Da-Lite PROFESSIONAL ELECTROL User manual

Da-Lite

Da-Lite MULTI-MASK IMAGER User manual

Da-Lite

Da-Lite TENSIONED DUAL MASKING ELECTROL User manual

Da-Lite

Da-Lite Tensioned Contour Electrol 38798LC User manual

Da-Lite

Da-Lite Tensioned Conference Electrol User manual

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL User manual

Da-Lite

Da-Lite C with CSR User manual

Da-Lite

Da-Lite ViewShare Tensioned Advantage Electrol... User manual

Da-Lite

Da-Lite Tensioned Advantage Deluxe Electrol Series User manual

Da-Lite

Da-Lite Picture King User manual

Popular Projection Screen manuals by other brands

FART PRODUKT

FART PRODUKT Standard SCREEN Installation instruction

Draper

Draper E Series Installation & operating instructions

Elite Screens

Elite Screens Elite Tripod Series user guide

Laarhoven

Laarhoven Companion II General assembly instructions

Renogy

Renogy RMS-LFPS-US manual

Samsung

Samsung S*H65* user manual

FONESTAR

FONESTAR PPTR-43100-FA quick start guide

Slide Clear

Slide Clear Varro XL installation instructions

Elite Screens

Elite Screens M85XWS1-SRM manual

OS РХ-090Н user manual

Niko

Niko 10-845 Product information

Speaka Professional

Speaka Professional 2357532 Important information

Sima

Sima XL-72 instruction manual

Jasic

Jasic EVO 2.0 ET-200P Fitting instructions

Elite Screens

Elite Screens Starling 2 Series user guide

InFocus

InFocus SC-WALL GRY-92H Instruction guide

Barco

Barco OverView MVL-615 Brochure & specs

Draper

Draper Envoy Installation & operating instructions