D-MAX DCC-500DV User manual
Digital Day & Night
COLOR DOME CAMERA
USER MANUAL
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards : Do NOT use power sources
other than that specified. Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform
to all local codes
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK),
NO USER SERVICEABLE PARTS INSIDE.
REFER WERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2 3
PrecautionsWarning
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time,
fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
Do not install the camera in
extreme temperature conditions.
Only use the camera under conditions
where temperatures are between -10
and 50 . Be especially careful to
provide ventilation when operating
under high temperatures.
It can cause the irnage quality to be
poor.
Do not install or use the camera in
an environment where the humidity
is high
Do not install the camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly. It is one of the most important parts of
the camera. Be careful not to be
stained by fingerprint.
Do not touch the front lens of the
camera.
54
Do not drop the camera or subject it
to physical shocks.
It can cause malfunctions to occur. It can damage the CCD.
Never keep the camera face to strong
light directly.
Do not expose the camera to rain or
spill beverage on it.
If it gets wet, wipe it dry immedi-ately.
Lipuids can contain minerals that
corrode the elexctronic com-ponents.
if it is exposed to radioactivity, For heated
ccD, it Will be out of order.
Do not expose the camera to
radioactivity.
If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
Please check that the power satisfies the normal specification before connecting the
camera.
Note
Contents
1. Features 6
2. Components & Cable Connection 8
3. Names and functions of parts 9
4. Installation & Dimension 10
5. Setup Menu Operation 11
6. Special Menu operation 17
7. Troubleshooting 23
8. Specifications 25
7
Horizontal Resolution 540 TVLines
Clear image quality has been achieved by employing a SONY CCD with 410,000
(effective) pixels, which provides a horizontal resolution of 540 TV lines.
DAY & NIGHT
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions
to provide optimum colors, and BW mode operates in nighttime conditions to
enhance the definition of the image.
Electronic IRIS
The electronic IRIS function enables continuous automatic control of the shutter
between 1/60~1/120,000 seconds.
PRIVACY Function
The PRIVACY function conceals the areas you do not wish to appear on the screen.
3Axis built-in Vandal Resistant Dome Housing
6
1. Features
High Sensitivity
The built-in high sensitivity SONY COLOR CCD enables a clear image even in
0.3Lux(0.1Lux B/W) or as low as 0.002Lux with SENS-UP.
DNR (Digital Noise Reduction)
The amount of low illuminance noise has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as horizontal resolution have been improved,
resulting in a clear and sharp image display even in the dark.
Controlled by OSD Menu
The camera can be controlled by selecting text displayed on the monitor screen.
Additional Functions
SENS-UP, MOTION DETECTION, MIRROR, SHARPNESS and SYNC (INT/LL)
functions are also available.
Water Proof(IP65)
98
1) Components
1) COLOR DOME CAMERA
2) SCREWS
3) WRENCH
4) MANUAL
2) Cable Connection
1) Names
2) Functions
3AXIS BRACKET
- Please loosen screws and fix tilted and panned position.
LENS : Vari-Focal Auto Iris Lens ( 4.0mm ~ 9.0mm / F1.5 )
OSD PCB
-SETUP button : Used for the menu display. This button can be used to confirm
settings after changing the value of the selected function or current conditions.
-UP & DOWN buttons : Used for selecting items by moving the cursor up or
down on the menu screen.
-LEFT & RIGHT buttons : Used when changing item values, by moving the
cursor to the left or right on the menu screen
2. Components & Cable Connection 3. Names and Functions of Parts
POWER
VIDEO
D C only
DC12V
DC INDCIN
①
③
②
1110
4. Installation & Dimension 5. Setup Menu Operation
1) Installation
2) Dimension
1) SETUP MENU Please press the SETUP button Settings can now be
made. The SETUP menu is displayed on the monitor.
Please select any function you wish to activate by using
the UP and DOWN buttons.
The arrow can be moved up or down by using the UP
and DOWN buttons.
Please position the arrow to point to the function you wish
to operate.
Please press the LEFT or RIGHT button if you wish to change mode.
When the LEFT or RIGHT button is pressed, available values and modes are
displayed in order. Please keep pressing the button until you get to the mode you
wish to operate.
Please select 'EXIT' and then press the SETUP button to finish the setting.
If appears at the mode you wish to operate, it means that there is a sub-menu
which can be selected by pressing the SETUP button.
If appears at the mode item, it means that there is no mode available to be
selected.
2) LENS
This function is used to adjust the brightness of the screen.
When the SETUP menu is displayed on the screen, please position the arrow to
point to 'LENS' by using the UP and DOWN buttons.
Please select the type of the lens you wish to use by pressing the LEFT or RIGHT
Button
DOME COVER
DECOR ATION
RING
No.8-32
UNC
BASE
H O U SING
RU BB ER
B O TO TOM
BO LT
MO U NT
M 4*10
83.5
46.0
(unit :
100.0
145.0
Φ
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
Note
1312
Please press the SETUP button if you wish to return to
the previous menu
- MANUAL : Manual lens selection
- DC : Auto iris lens selection
The brightness of the screen can be adjusted in DC mode.
The brightness can be adjusted within the range of 1 ~ 70.
The optimum level of brightness for the user can be
achieved by adjustment.
If you select the MANUAL mode, it can be adjusted in
ESC mode.
3) SHUTTER
Auto or manual control can be selected.
When the SETUP menu is on the screen, please position
the arrow to point to 'SHUTTER' by using the UP and
DOWN buttons.
Please select the ESC shutter mode by pressing the
LEFT or RIGHT button.
- FLK : Please select 'FLK' mode when flickering occurs on
the screen, due to an imbalance between illumination and
frequency. (NTSC Model:1/100, PAL Model: 1/120)
- ESC : Auto control of the shutter speed can be achieved. When ESC mode is on,
the speed is controlled automatically according to the brightness of the screen.
- MANUAL : The shutter speed can be controlled manually.
While using the internal synchronous system, if the shutter setting is on 'ESC' and
the camera is directly facing a bright fluorescent light, the image on the screen can
be dversely affected. Therefore please choose the installation location with care.
When 'MANUAL' mode is on, the SENS UP function does not operate.
4) WHITE BALANCE
The screen color can be adjusted by using the WHITE BALANCE function.
Please position the arrow to point to 'WHITE BAL' on the
SETUP menu by using the UP and DOWN buttons
Please select the mode you wish to operate by pressing
the LEFT or RIGHT button.
- ATW(Auto Tracking White Balance) : This mode can
be used within the color temperature range 1,800°K ~
10,500°K (eg, fluorescent light, outdoor, sodium vapor
lamp or inside tunnels)
- AWC(Auto White Balance Control) : Please press the SETUP button while the
camera is directed at a piece of white paper to obtain the optimum state under
current illumination. If the environment including the light source is changed you
have to adjust the white balance again.
- MANUAL : The manual adjustment mode enables finer adjustment.
Please select ATW or AWC first. Please change to manual adjustment mode and
press the SETUP button. Please set the appropriate color temperature, and then
increase or decrease the red and blue color values while monitoring the color
changes on the object.
Under the following conditions the WHITE BALANCE function may not operate
properly. In such cases, please select the AWC mode.
LENS
brightness 50
Press Set to Return
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
SETUP
LENS DC
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
Note
Note
Note
1514
When the object's surroundings have a very high color temperature (eg, a clear sky
and sunset)
When the object's surroundings are dark
If the camera directly faces a fluorescent light or is installed in a place where there
are considerable changes in illumination, the WHITE BALANCE function may
become unstable.
5) BACKLIGHT
When there is a strong backlight behind the object, clear images of the background
as well as the object can still be obtained by using the backlight function.
Please position the arrow to point to 'BACKLIGHT' on the
SETUP menu by using the UP and DOWN buttons.
Please select the mode you wish to operate by pressing
the LEFT or RIGHT button.
- HIGH : The gain increases from 0dB up to 42dB.
- MIDDLE : The gain increases from 0dB up to 30dB.
- LOW : The gain increases from 0dB up to 18dB.
- OFF : BACKLIGHT function does not operate.
6) AGC (AUTO GAIN CONTROL)
Please position the arrow to point to 'AGC' on the SETUP
menu by using the UP and DOWN buttons.
Please select the mode you wish to operate by pressing
the LEFT or RIGHT button. As the level of gain increases,
the screen gets brighter and the level of noise also
increases.
- HIGH : The gain increases or decreases within the
range of 6dB ~ 42dB.
- MIDDLE : The gain increases or decreases within the range of 6dB ~ 30dB.
- LOW : The gain increases or decreases within the range of 6dB ~ 18dB.
- OFF : The gain is fixed at 6dB.
7) DNR
The background noise in the low light level decreases automatically as the level of
gain changes. Please position the arrow to point to 'DNR' on the SETUP
menu by using the UP and DOWN buttons.
Please select the mode you wish to operate by pressing
the LEFT or RIGHT button.
- OFF : There is no reduction in noise level.
- LOW : There is a small reduction in noise level with
almost no ghost image.
- MIDDLE : The most effective mode. There is a sufficient reduction in noise levels
without causing much ghost imaging.
- HIGH : The level of noise is reduced greatly, however there is an increase in ghost
imaging.
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
BACKLIGHT ON BACKLIGHT OFF
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
1716
When AGC is turned off, DNR does not operate.
8) SENS UP
SENS UP helps maintain a bright, clear screen image by automatically detecting
changes in the level of light in low light level conditions
Please position the arrow to point to 'SENS UP' on the
SETUP menu by using the UP and DOWN buttons.
Please select the mode you wish to operate by pressing
the LEFT or RIGHT button.
Please press the SETUP button when all the settings are
complete.
The maximum storage magnification in low light level
movement situations can be adjusted by pressing the
SETUP button in 'AUTO' mode.(X2~X128)
As the magnification increases, the screen gets brighter; however the after image
also increases
If storage magnification is increased while SENS UP is operating, it may cause
noise, and spots may appear; however this is normal.
- AUTO : Low light level auto mode
- OFF : The function does not operate
When SHUTTER is in the manual mode, SENS UP does not operate.
When AGC is turned off, SENS UP does not operate.
9) EXIT
Saves all the setting menus and then exits.
1) SPECIAL MENU
Please position the arrow to point to 'SPECIAL' on the
SETUP menu by using the UP and DOWN buttons.
Please select the mode you wish to operate by pressing
the UP or DOWN button
2) CAMERA ID
If the ID is input, the camera ID appears on the monitor.
Please position the arrow to point to 'CAMERA ID' by
using the UP or DOWN button.
Please select 'ON' by pressing the LEFT or RIGHT
button.
Please press the SETUP button.
Up to 15 letters can be used for the ID.
- Please move the cursor to the letter you wish to choose by using the UP and
DOWN button.
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
6. Special Menu Operation
SETUP
LENS MANUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
SETUP
CAMERA ID OFF
COLOR ON
SYNC INT
MOTION DET OFF
PRIVACY OFF
MIRROR OFF
SHARPNESS ON
RESET
RETURN
Camera ID
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-. 0123456789
CLR POS END
-------------------------
Note
Note
Table of contents
Other D-MAX Security Camera manuals
D-MAX
D-MAX DCC-500D User manual
D-MAX
D-MAX DCC-601DV User manual
D-MAX
D-MAX DWC-540DV User manual
D-MAX
D-MAX 650 TVL User manual
D-MAX
D-MAX DSC-300SE User manual
D-MAX
D-MAX DMC-20SEC User manual
D-MAX
D-MAX Pixim Seawolf DSP User manual
D-MAX
D-MAX DWC-548DV User manual
D-MAX
D-MAX DCC 600d Series User manual
D-MAX
D-MAX DMC Series User manual
D-MAX
D-MAX DSC-2000Si User manual
D-MAX
D-MAX DCC-700d Series User manual
D-MAX
D-MAX DIC-7030DV User manual
D-MAX
D-MAX DCC-520D series User manual
D-MAX
D-MAX 680 TVL User manual
D-MAX
D-MAX DSC-230SI User manual
D-MAX
D-MAX DCC-580D Series User manual
D-MAX
D-MAX DHC-10SITA User manual
D-MAX
D-MAX DCC-501DV User manual
D-MAX
D-MAX DCC-600F User manual
