D-Link DCS-6314 User manual
This document will guide you through the
basic installation process for your new D-Link
Network Camera.
DCS-6314
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
Full HD Outdoor Fixed Dome Network Camera
D-Link DCS-6314 Quick Install Guide 1
ENGLISH
DCS-6314 Quick Install Guide
This installation guide provides basic instructions for installing the DCS-6314 Network
Camera on your network. For additional information about how to use the camera,
please see the User’s Manual which is available on the CD included in this package or
from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. Micro SD Card Installation
4. Hardware Installation
5. Conguration with Wizard
6. Adjusting the lens 3-axis angel
1. Package Contents
DCS-6314 Network Camera
Manual and Software on CD-ROM
Quick Install Guide
Power Adapter
Security Wrench
CAT-5 Ethernet Cable
Screws and wall socket
Weather Shield
4Pin Terminal Block
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all
local codes and prevent voiding your warranty.
D-Link DCS-6314 Quick Install Guide
2
ENGLISH
2. Hardware Overview
Power Connector
Connects to 12 V DC power
Ethernet Jack
RJ-45 connector for Ethernet
whichcan also be used to power
the camera using Power over
Ethernet (PoE)
Reset Button
Resets camera to factory
default settings
Audio In
Connects to a microphone
DI/DO Wiring, 12V DC output
I/O connectors for external
devices
Audio Out
Connects to speakers
Install the Micro SD Card
Push the Micro SD card into the camera with the gold
contacts oriented towards the base of the camera. To eject
the Micro SD card, push the Micro SD card into the slot.
3. Micro SD Card Installation
Disassemble the Camera
Open the camera enclosure by loosen the
3 screws. Lift the dome off the base of the
camera.
D-Link DCS-6314 Quick Install Guide 3
ENGLISH
4. Standard Mounting Instructions
Mounting Installation
Please see the User Manual for detailed instructions regarding installation and mounting
of the camera using a mounting bracket.
Style 1 - Concealed Cable Installation
Height: 25.6 mm (1.0 inches)
Diameter: 122 mm (4.8 inches)
Weight: 135g (0.3 lbs)
Figure 2.2Figure 2.1
Weather Shield
Weather shield
screw
D-Link DCS-6314 Quick Install Guide
4
ENGLISH
Style 2 - Exposed Cable Installation
Height: 25.6 mm (1.0 inches)
Diameter: 122 mm (4.8 inches)
Weight: 135g (0.3 lbs)
Figure 2.3 Figure 2.4
Figure 2.5
D-Link DCS-6314 Quick Install Guide 5
ENGLISH
Pendant Mount (DCS-34-2)
Height: 201 mm (7.9 inches)
Diameter: 150 mm (5.9 inches)
Weight: 665 g (1.45 lbs)
Figure 3.4
Pendant
Bracket
Bracket
Cap
Rubber
Seal
Figure 3.2
Figure 3.3
Figure 3.1
Bracket
Cap
Mounting
Plate
D-Link DCS-6314 Quick Install Guide
6
ENGLISH
Bent Mount (DCS-34-3)
Height: 253 mm (9.96 inches)
Diameter: 150 mm (5.9 inches)
Weight: 770 g (1.7 lbs)
Bracket Cap
Bent
Bracket
Figure 4.2
Figure 4.4Figure 4.3
Figure 4.1
Bracket
Cap
Mounting
Plate
Dome
Camera
Bent
Bracket
D-Link DCS-6314 Quick Install Guide 7
ENGLISH
Connection with a PoE Hub
If you are using a PoE hub, connect the IP camera to the hub via an Ethernet cable,
which will provide transmission of both power and data over a single cable.
General Connection Using 12 V DC Power Adapter
1. Connect the network camera to a hub via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.
D-Link DCS-6314 Quick Install Guide
8
ENGLISH
5. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6314 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to
nish.
D-Link DCS-6314 Quick Install Guide 9
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click
Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select static IP if the
camera will use the same IP address each time it is
started.
Click Next, to proceed to the next page.
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click Next, to proceed to the next page.
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you have
a DHCP server on your network, a valid IP Address
will be displayed. If your network does not use a
DHCP server, the network camera's default static IP
192.168.0.20 will be displayed.
Click the Wizard button to continue.
Other manuals for DCS-6314
8
Table of contents
Other D-Link Security Camera manuals
D-Link
D-Link SECURICAM DCS-6511 User manual
D-Link
D-Link DCS-3710 User manual
D-Link
D-Link DCS-4703E User manual
D-Link
D-Link DCS-2130 User manual
D-Link
D-Link DCS-8325LH User manual
D-Link
D-Link DCS-936L User manual
D-Link
D-Link DCS-942L User manual
D-Link
D-Link DCS-6915 User manual
D-Link
D-Link DCS-6314 User manual
D-Link
D-Link DCS-942L User manual
D-Link
D-Link DCS-4703E User manual
D-Link
D-Link DCS-3411 User manual
D-Link
D-Link SECURICAM Network DCS-3220G User manual
D-Link
D-Link DCS-4712E User manual
D-Link
D-Link DCS-7413 User manual
D-Link
D-Link DCS-7410 User manual
D-Link
D-Link DCS-3716 User manual
D-Link
D-Link DCS?6010L User manual
D-Link
D-Link SECURICAM DCS-5605 User manual
D-Link
D-Link SECURICAM DCS-5605 User manual
