D-Link DCS-4802E User manual
This document will guide you through the
basic installation process for your new
D-Link Network Camera.
DCS-4802E
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
Vigilance Full HD Outdoor PoE Mini Dome Camera
Quick Installation Guide
Installationsanleitung
Guide d’installation
Guía de instalación
Guida di Installazione
Краткое руководство по установке
Guia de Instalação Rápida
快速安裝指南
Petunjuk Pemasangan Cepat
D-Link DCS-4802E Quick Installation Guide 1
ENGLISH
Quick Installation Guide
This installation guide provides basic instructions for installing the DCS-4802E on your
network. For additional information about how to use the camera, please see the User
Manual, which is available on the CD included in this package, or you can download it
from the D-Link support website.
Package Contents
DCS-4802E Vigilance Full HD Outdoor PoE Mini Dome Camera
Cable Waterproong Connector
Rubber Power Connector Plug
Mounting Kit
Manual and Software on CD-ROM
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all
local codes and prevent voiding your warranty.
D-Link DCS-4802E Quick Installation Guide
2
ENGLISH
Hardware Overview
IR LEDs
Provide illumination for
low-light environments
Light Sensor
Detects lighting conditions
Reset Button
Resets camera back to the
factory default settings
Ethernet Jack
RJ-45 connector for Ethernet which can also be used to
power the camera using Power over Ethernet (PoE)
Power Connector
Connects to an optional 12 V / 1.5 A
power adapter (not included)
Camera Lens Camera Base Cover
D-Link DCS-4802E Quick Installation Guide 3
ENGLISH
Connecting the Camera
You can power the DCS-4802E two different ways: Power over Ethernet (PoE) or with a
power adapter.
Powering the camera using PoE (Class 2):
Connect an Ethernet cable to the Ethernet jack on the camera. Connect the other
end of the cable to your PoE switch or PoE injector.
Powering the camera with a power adapter
(not included):
Connect a 12 V, 1.5 A power adapter to the power connector.
Connect an Ethernet cable to the Ethernet jack on the camera. Connect the other
end of the cable to your network.
D-Link DCS-4802E Quick Installation Guide
4
ENGLISH
Conguring the Camera
Insert the DCS-4802E CD into your computer's CD-ROM drive to begin the installation.
If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to
start automatically, click the Start button and type D:\autorun.exe (where D: represents
the drive letter of your CD-ROM drive) and press Enter.
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu (Start > D-Link >
Setup Wizard SE).
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you have a
DHCP server on your network, a valid IP Address will be
displayed. If your network does not use a DHCP server,
the network camera's default static IP 192.168.0.20 will be
displayed.
Select your camera, then click the Wizard button to
continue.
Click Setup Wizard and follow the instructions to install
the Setup Wizard.
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click the checkboxes if you wish to change the admin ID
and password for the camera, and enter the new ID and
password you wish to use.
Click Next to continue.
Select DHCP if your camera obtains an IP address
automatically from a DHCP server such as a router.
Select Static IP if you want to manually enter the IP
settings for the camera.
Click Next to continue.
D-Link DCS-4802E Quick Installation Guide 5
ENGLISH
Viewing Your Camera via Web Browser
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu (Start > D-Link >
Setup Wizard SE).
Select the camera and click Link to access the web
conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
This section displays your camera’s live video. You can
select your video prole and view or operate the camera.
For additional information about web conguration, please
refer to the user manual included on the CD-ROM or the
D-Link website.
Enter your username (default is admin) and your
password (default is blank). Click OK to continue.
Take a moment to conrm your settings and click Restart.
D-Link DCS-4802E Quick Installation Guide
6
ENGLISH
Mounting Instructions
It is highly recommended that you congure and test your camera before mounting it.
Place the mounting sticker where you want to position the
camera.
Use a 6 mm drill bit to make the required holes
approximately 25 mm deep, then insert the wall anchors
into the holes.
If you are running the camera cables through the wall
or ceiling, drill a hole in the center and pull the cables
through the hole. If not, then guide the camera cables
through the cable channel on the base after mounting to
the wall or ceiling.
Use the screws provided to mount the camera to the wall
or ceiling.
Attach the camera base cover by lining up the cable
channel with the mark on the camera base, then turn the
camera base cover clockwise until it clicks.
D-Link DCS-4802E Quick Installation Guide 7
ENGLISH
To waterproof your camera installation, follow the instructions below. Round Ethernet
cable, a crimping tool, and RJ-45 plugs are required for this procedure.
Waterproong Your Installation
Place the washer around the base of the Ethernet
connector as shown.
Connect the RJ-45 plug into the Ethernet connector, then
screw the waterproof connector to the Ethernet connector
by turning it about a half-turn clockwise.
Thread bare Ethernet cable through the waterproof
connector as shown, then crimp an RJ-45 plug onto the
cable.
D-Link DCS-4802E Quick Installation Guide
8
ENGLISH
If you are using PoE to power your camera, attach
the included rubber power connector plug to the power
connector.
If you are using a power adapter (not included) to
power your camera, wind waterproof tape around the
connection in an overlapping manner to cover it.
Additional Information
Additional help and product information is available online at http://www.dlink.com.
Warranty Information
Please visit http://warranty.dlink.com/ for warranty information for your region.
Turn the back part of the waterproof connector clockwise
until there is a tight seal around the Ethernet cable.
Other manuals for DCS-4802E
3
Table of contents
Other D-Link Security Camera manuals
D-Link
D-Link DCS-930L User manual
D-Link
D-Link DCS 6513 User manual
D-Link
D-Link DCS-850L User manual
D-Link
D-Link DCS-8000LH User manual
D-Link
D-Link DCS-1130 - mydlink-enabled Wireless N Network... User manual
D-Link
D-Link DCS-4701E User manual
D-Link
D-Link DCS-8000LHV3 User manual
D-Link
D-Link DCS-3710 User manual
D-Link
D-Link DCS-6045L User manual
D-Link
D-Link DCS-2802KT-EU User manual
D-Link
D-Link DCS-6517 User manual
D-Link
D-Link SECURICAM DCS-6511 User manual
D-Link
D-Link DCS-5020L User manual
D-Link
D-Link SECURICAM DCS-6511 User manual
D-Link
D-Link DCS-6315 User manual
D-Link
D-Link DCS-932L User manual
D-Link
D-Link DCS-3710 User manual
D-Link
D-Link DCS-960L Operating and maintenance instructions
D-Link
D-Link Securicam DCS-3415 User manual
D-Link
D-Link DCS-H100 User manual
