D-Link DCS-4705E User manual
This document will guide you through the
basic installation process for your new
D-Link Network Camera.
DCS-4705E
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
Vigilance 5 Megapixel H.265 Outdoor Bullet Camera
Quick Installation Guide
Installationsanleitung
Guide d’installation
Guía de instalación
Guida di Installazione
Краткое руководство по установке
КОРОТКИЙ ПОСІБНИК ЗІ ВСТАНОВЛЕННЯ
Guia de Instalação Rápida
快速安裝指南
Petunjuk Pemasangan Cepat
1
D-Link DCS-4705E Quick Installation Guide 1
ENGLISH
Quick Installation Guide
This installation guide provides basic instructions for installing the Network
Camera on your network. For additional information about how to use the
camera, please see the User Manual which is available on the CD included in
this package or from the D-Link support website.
Package Contents
DCS-4705E Vigilance 5 Megapixel H.265 Outdoor Bullet Camera
Cable Waterproong Connector
Rubber Power Connector Plug
Mounting Kit
Manual and Software on CD-ROM
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to
conform to all local codes and prevent voiding your warranty.
2D-Link DCS-4705E Quick Installation Guide
2
ENGLISH
Hardware Overview
Camera Lens
IR LEDs
Provide illumination for
low-light environments
Adjustment Ring
Loosen to adjust camera
angle and tighten to lock
camera angle
Reset Button
Press and hold for 10
seconds to reset camera
back to the factory default
settings
Grounding Screw
Can be attached to a
grounding wire if desired
Power Connector
Connects to an optional 12 V / 1.5 A power
adapter (not included)
Ethernet Jack
RJ-45 connector for Ethernet, can
also be used to power the camera
using Power over Ethernet (PoE)
3
D-Link DCS-4705E Quick Installation Guide 3
ENGLISH
Conguring the Camera
Insert the DCS-4705E CD into your computer's CD-ROM drive to begin
the installation. If the Autorun function on your computer is disabled, or if
the D-Link Launcher fails to start automatically, click Start > Run. Type D:\
autorun.exe, where D: represents the drive letter of your CD-ROM drive.
Click on the D-Link Setup Wizard SE icon that
was created in your Windows Start menu (Start >
D-Link > Setup Wizard SE).
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you
have a DHCP server on your network, a valid IP
Address will be displayed. If your network does not
use a DHCP server, the network camera's default
static IP 192.168.0.20 will be displayed.
Select your camera, then click the Wizard button to
continue.
Click Setup Wizard and follow the instructions to
install the Setup Wizard.
Enter the Admin ID and password. When logging in
for the rst time, the default Admin ID is admin with
the password left blank.
Click the checkboxes if you wish to change the
admin ID and password for the camera, and enter
the new ID and password you wish to use.
Click Next to continue.
Select DHCP if your camera obtains an IP address
automatically from a DHCP server such as a router.
Select Static IP if you want to manually enter the IP
settings for the camera.
Click Next to continue.
4D-Link DCS-4705E Quick Installation Guide
4
ENGLISH
Take a moment to conrm your settings and click
Restart.
Viewing Your Camera via Web Browser
Click on the D-Link Setup Wizard SE icon that
was created in your Windows Start menu (Start >
D-Link > Setup Wizard SE).
Select the camera and click Link to access the web
conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
This section displays your camera’s live video. You
can select your video prole and view or operate
the camera. For additional information about web
conguration, please refer to the user manual
included on the CD-ROM or the D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.
5
D-Link DCS-4705E Quick Installation Guide 5
ENGLISH
Mounting Instructions
It is highly recommended that you congure and test your camera before
mounting it.
If you need to waterproof your installation, please continue to the next page.
Place the mounting sticker where you want to
position the camera. Make sure the camera base
will be positioned so that the cable channel is on
the bottom.
Use a 6 mm drill bit to make the required holes
approximately 25 mm deep, then insert the wall
anchors into the holes.
If you are running the camera cables through
the wall, drill a hole in the center and pull the
cables through the hole.
Connect the power and Ethernet cables, or just the
Ethernet cable if you are using a PoE connection.
Use the screws provided to mount the camera to
the wall.
If you are running the camera cables out the
side of the camera, guide the camera cables
through the cable channel on the base.
To adjust the camera's angle, turn the adjustment
ring counterclockwise to loosen it, then move the
camera to the desired position and angle. When
you are nished, turn the adjustment ring clockwise
to tighten it.
6D-Link DCS-4705E Quick Installation Guide
6
ENGLISH
To waterproof your camera installation, follow the instructions below. Round
Ethernet cable, a crimping tool, and RJ-45 plugs are required for this
procedure.
Waterproong Your Installation
Place the washer around the base of the Ethernet
connector as shown.
Connect the RJ-45 plug into the Ethernet
connector, then screw the waterproof connector
to the Ethernet connector by turning it about a
half-turn clockwise.
Thread bare Ethernet cable through the waterproof
connector as shown, then crimp an RJ-45 plug onto
the cable.
7
D-Link DCS-4705E Quick Installation Guide 7
ENGLISH
If you are using PoE to power your camera, use
the included rubber power connector plug to the
power connector.
If you are using a power adapter(not included)
to power your camera, wind waterproof tape
around the connection in an overlapping manner to
cover it.
Additional Information
Additional help and product information is available online at
http://www.dlink.com.
Warranty Information
Please visit http://warranty.dlink.com/ for warranty information for your region.
Screw the back part of the waterproof connector
clockwise until there is a tight seal around the
Ethernet cable.
8
8D-Link DCS-4705E Quick Installation Guide
DEUTSCH
Installationsanleitung
Diese Installationsanleitung bietet Ihnen grundlegende Anleitungen zur
Installation der Netzwerkkamera in Ihrem Netzwerk. Zusätzliche Informationen
zur Verwendung der Kamera nden Sie im Benutzerhandbuch, das Ihnen auf
der CD, die diesem Paket beiliegt, oder über die D-Link Support-Website zur
Verfügung steht.
Packungsinhalt
DCS-4705E Vigilance 5 Megapixel H.265 Outdoor Bullet Camera
Wasserdichter Anschlussstecker
Netzanschlussstecker aus Hartgummi
Montageset
CD-ROM mit Software und Handbuch
Installationsanleitung
Sollte einer der oben aufgeführten Artikel fehlen, wenden Sie sich bitte an
Ihren Fachhändler.
Sicherheitshinweis:
Installation und Wartungsarbeiten sollten nur von zertizierten Technikern
vorgenommen werden, zu jeder Zeit allen örtlich geltenden Richtlinien und
Anforderungen entsprechen sowie verhindern, dass Ihr Garantieanspruch
erlischt.
Other manuals for DCS-4705E
3
Table of contents
Languages:
Other D-Link Security Camera manuals
D-Link
D-Link DCS-3420 User manual
D-Link
D-Link DCS-2670L User manual
D-Link
D-Link DCS-4602EV User manual
D-Link
D-Link DCS-930L Manual
D-Link
D-Link DCS-4605EV User manual
D-Link
D-Link SECURICAM DCS-7110 User manual
D-Link
D-Link DCS-942L User manual
D-Link
D-Link SECURICAM Network DCS-5300G User manual
D-Link
D-Link DCS-3411 User manual
D-Link
D-Link DCS-7510 User manual
D-Link
D-Link DCS 6210 User manual
D-Link
D-Link DCS-71 Series User manual
D-Link
D-Link DCS-7513 User manual
D-Link
D-Link DCS-7517 User manual
D-Link
D-Link DCS-2310L User manual
D-Link
D-Link SECURICAM DCS-6511 User manual
D-Link
D-Link DCS-8000LH User manual
D-Link
D-Link DCS-942L User manual
D-Link
D-Link DCS-3430 User manual
D-Link
D-Link DCS-5029 User manual
