D-Link DGE-560SX User manual

Gigabit Ethernet 1000BASE-SX(LC)

PCI-Express X4 Adapter

User Manual

(September 2006) Ver.1.00

P/N: 6DGE560SX.01G

RECYCLABLE

Contents

IMPORTANT INFORMATION............................................................................................................ 1

What’s New ............................................................................................................................................... 1

System Hardware Requirements ....................................................................................................... 1

Operating Systems Supported:................................................................................................................... 1

INTRODUCTION ................................................................................................................................ 2

Summary of Features ......................................................................................................................... 2

LED Indicators .................................................................................................................................... 2

INSTALLATION ................................................................................................................................. 3

Unpack and Inspect............................................................................................................................ 3

Installing the Adapter.......................................................................................................................... 3

Connecting the Network Cable........................................................................................................... 4

Software Installation ........................................................................................................................... 4

D-Link Network Control Program ....................................................................................................... 5

Advanced Adapter Configuration ....................................................................................................... 8

TECHNICAL SPECIFICATIONS ....................................................................................................... 9

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

Important Information

Please read the information below before installing the D-Link Gigabit Ethernet 1000BASE-SX(LC) PCI-

Express X4 Adapter on your system.

What’s New

The latest generation PCI (Peripheral Component Interconnect) bus architecture called PCI Express, uses a 2.5-

GHz serial Input/Output structure for higher bandwidth and better scalability than its previous architectures. The

DGE-560SX 1000BASE-SX (LC) PCI-Express x4 supports up to 2 Gbps total bidirectional throughput. The

faster serial-bus architecture provides bidirectional dedicated Input/Output with 2.5-GHz clocking, compared to

133-MHz parallel bus of the previous generation PCI-Expanded (PCI-X).

System Hardware Requirements

Before installing the DGE-560SX, check to be sure your system meets the following minimum requirements:

• Available PCI-Express (x4 or higher) card slot

• 64 MB of System Memory

• 150 MHz or faster processor

• The most recent BIOS version for your system

• In addition to these system requirements, the optical network interface requires a 850nm LC Fiber

Optical connector

Hardware Driver Compatability

To ensure optimal performance, it is recommended that you download the latest hardware drivers for all your

particular adapters from the manufacturer's web site.

It is recommended that you install the latest Service Packs and/or Hot Fixes from Microsoft prior to installing D-

Link PCI-Express Card Software. Refer to the Release Notes for the latest list of Service Packs and/or Hot Fixes

that are required.

Operating Systems Supported:

• Microsoft Windows 2000, 2000 server

• Microsoft Windows Server 2003, Server 2003 x64 Edition

• Microsoft Windows XP

• Microsoft Windows XP x64 Edition

• Linux for Kernel 2.4.x, 2.6.x

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

Introduction

The DGE-560SX 1000BASE-SX (LC) PCI-Express x4 network adapter card is ideal for optical Gigabit

Ethernet to desktop PC networking. The card is capable of supporting total bidirectional bandwidth of up to 2

Gbps and can be installed on a desktop PC or server.

Notable features of the DGE-560SX include VLAN tagging, LED display for linkage and activity, Flow Control

and 802.1p Priority support.

Summary of Features

Designed for versatility and performance, the DGE-560SX provides the following:

• Compliant with IEEE 802.3z specification for 1000Base-SX Ethernet standards

• Support PCI-E 1.0a interface with 2.5GHz signaling

• 9K bytes Jumbo frame support

• Support IEEE 802.1p (QoS)

• Support IEEE 802.1q VLAN

• With D-Link Network Control Program for advanced feature setting

• Simple Network Management Protocol (SNMP) Support

• Compliant to IEEE 802.3x for flow control and full-duplex operation

• Promiscuous Mode

• Support Full-duplex operation

• Link / Act LED

• Transmission distance range:

- 75 meter in 62.5 / 125 micron-meter multi-mode fiber cable

- 550 meter in 50 / 125 micron-meter multi-mode fiber cable

Driver Support for:

- Microsoft Windows 2000, 2000 server

- Microsoft Windows Server 2003, Server 2003 x64 Edition

- Microsoft Windows XP

- Microsoft Windows XP x64 Edition

- Linux for Kernel 2.4.x, 2.6.x

LED Indicators

The DGE-560SX Adapter features three LED indicators:

• Act (Activity) Flashing green indicates activity (transmitting or receiving) within the adapter.

• Link Steady green indicates good linkage between the DGE-560SX and its supporting server or switch.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

Installation

Follow the instructions in this section to install the adapter.

Unpack and Inspect

Caution: Under ordinary circumstances, a DGE-560SX card will not be affected

by static charge. In some circumstances where you may carry an extraordinarily

high static charge, it is good practice to reduce the charge by touching a ground

before handling the adapter card.

Open the shipping carton and carefully remove all items. Make sure you have the following items:

• One DGE-560SX 1000BASE-SX(LC) PCI-E x4 Adapter Card

• CD-ROM containing system drivers, and Quick Installation Guide

Installing the Adapter

1. Shut down the computer, unplug its power cord, and remove the chassis cover.

2. Insert the contact edge of the DGE-560SX card into the connector of an available PCI-Express (x4 or

higher) Bus expansion slot. Press the card firmly into the connector such that the card’s contacts are fully

seated in the PCI connector.

3. Install the bracket screw that secures the card to the computer chassis.

4. Replace the computer’s chassis cover.

5. Reconnect the computer’s power cord, and switch computer power on. If the BIOS section of your

computer’s boot program is Plug-and-Play compliant, then at power-up the BIOS will automatically

configure any newly installed DGE-560SX adapter.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

Connecting the Network Cable

The DGE-560SX 1000Base-SX Gigabit Ethernet network adapter card enables operation over 850nm 62.5/125

fiber optic cable up to 75 meters and 850nm 50/125 fiber optic cable up to 550 meters. The network adapter card

connects to fiber optic cabling equipped with an LC Fiber Optical connector.

Software Installation

To install the driver or the D-Link Network Control Program, insert the CD-ROM in the CD-ROM drive of the

system with the installed adapter.

The D-Link Network Control Program is included with the DGE-560SX. This program is used to monitor the

adapter and create VLAN information including VLAN Identifier and name for the system in which it is

installed.

To install the D-Link Network Control Program, insert the CD-ROM in the system CD-ROM drive and click the

Install link. Follow the instructions that appear to install the program.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

D-Link Network Control Program

To launch the D-Link Network Control program, double-click the D-Link Network Control icon in the Control

Panel folder.

NOTE: D-Link Network Control Program can be installed and used on Windows 2000,

Windows XP and Windows Server 2003.

The Network Control menu lists adapters installed on the system. For systems with multiple adapters installed,

select the DGE-560SX from the list and click OK. Click the menu tab for the menu you want to view.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

NOTE: The Power Management and Sensors functions are not currently supported on

the adapter.

To add VLAN ID, click the Virtual LAN menu tab.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

In the Virtual LAN menu tab, click the Add VLAN button.

In the Add Virtual LAN pop-up menu, select the Virtual LAN ID (VID) number used for the system. A Virtual

LAN Name can also be created but is optional. The Add Virtual LAN menu is also used to configure Jumbo

Frames, Transmit Buffers, and Receive Buffers.

Gigabit Ethernet 1000BASE-SX(LC) PCI-Express X4 Adapter

Advanced Adapter Configuration

The DGE-560SX supports advanced features including the SNMP agent described in the separate SNMP Agent

Manual, and support for 802.1p priority. To enable or disable 802.1p support on the adapter, go to the

Properties menu (right-click on Local Area Connection icon in Network Connections) and click the

Configure button:

Click the Advanced tab in the men that appears:

Use the Advanced configuration menus to configure 802.1p, select 802.1p Support from the Property list and

choose On to enable or Off to disable from the Value pull-down menu.

Other advanced configuration features that can be changed or enabled include Flow Control, Jumbo Frames,

Log Status Messages, Transmit and Receive buffers and others.

Other manuals for DGE-560SX

Table of contents

Other D-Link Adapter manuals

D-Link

D-Link DWA-180 User manual

D-Link

D-Link DVG-2102S User manual

D-Link

D-Link DWM-152 User manual

D-Link

D-Link AirPlus XTREME G DWL-G680 User manual

D-Link

D-Link DHP-W610AV User manual

D-Link

D-Link AirPro DWL-A650 User manual

D-Link

D-Link AirPro DWL-AB650 User manual

D-Link

D-Link DWA-525 User manual

D-Link

D-Link 802.11g Wireless LAN USB Adapter DWL-G122 User manual

D-Link

D-Link DWL-500 - 11Mb Wireless LAN PCI Network Card User manual

D-Link

D-Link DHP-P500AV User manual

D-Link

D-Link DHP-341 User manual

D-Link

D-Link DWL-P200 User manual

D-Link

D-Link DHP-501AV User manual

D-Link

D-Link DFE-530TX User manual

D-Link

D-Link DWA-582 User manual

D-Link

D-Link DE-220PCT - Ethernet 10 Mbps ISA Nic Combo User manual

D-Link

D-Link DWL-G630 - AirPlus G 802.11g Wireless PC... User manual

D-Link

D-Link DUB-2312 User manual

D-Link

D-Link DWA-566 User manual

D-Link

D-Link DWA-547 User manual

D-Link

D-Link DWB-120M User manual

D-Link

D-Link DHP-700AV User manual

D-Link

D-Link PowerLine DHP-302 User manual

Popular Adapter manuals by other brands

PCB Piezotronics

PCB Piezotronics 090B274 Installation and operating manual

Auvidea

Auvidea J20 Technical reference manual

Gossen MetraWatt

Gossen MetraWatt AT3-III E operating instructions

Akribis

Akribis ITF-21-BISS-MIT user manual

Tenda

Tenda W54U user guide

ROHO

ROHO AGILITY Operation manual

PROLiNK

PROLiNK WN2001 Quick installation guide

Hawking

Hawking HUF2 Specifications

Airlink101

Airlink101 AWLC4030 user manual

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter user manual

Philips

Philips SWA4554S/10 user manual

JVC

JVC TS-C9D2B Assembly and installation instructions

NETGEAR

NETGEAR A6100 quick start

Philips

Philips SWA2037 Specifications

Basalte

Basalte 0610-20 installation manual

Yealink

Yealink EHS40 user guide

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A installation guide

RCA

RCA AH57R manual