Creo Trendsetter NEWS SA User manual

www.creo.com

Internal 732-00041A-EN-RevA

Visual Quick Reference

English

653-00979A-EN-A

February 2005

Trendsetter® NEWS SA

Trendsetter NEWS SA Operational Lights and What They Mean

Operator interface lights

Operator Interface Lights Operator Action

Imaging Light Flashing green Wait—the device is imaging a plate.

Load Light Flashing green

Semi-automatic mode—load one or two plates for imaging.

Semi-automatic mode—wait, the device is unloading a plate.

Error Light Flashing yellow An error has occurred and the job is suspended.

Trendsetter NEWS SA

Imaging Plates Using Different Workﬂ ows

Prinergy

Brisque

TIFF Workﬂ ow

1In Prinergy, click OK to submit the ﬁ le.

1In Brisque, click Submit to submit the ﬁ le.

1In Print Console, click Open to

submit the ﬁ le.

2Right-click the job and

select Approve.

The output device receives the job in Print Console.

The output device receives the job.

Trendsetter NEWS SA Imaging a Plate

* Refer to the Operator Guide for full details.

2In Print Console:

a. Click Open to submit the ﬁ le. b. Ensure that the correct media

is available for loading.

The load light glows green.

Plate imaging

7Press the Start button. 8Unload the media.

4Position media on the load ramp.

3Remove all slip sheets.

The load light ﬂ ashes green.

The load light glows solid green.

Media alignment label

The imaging light ﬂ ashes green.

5Lower the media gently until it

touches the registration pins.

6Align the media on the load ramp.

Double-wide

(panorama)

Single-wide

(broadsheet)

1Ensure the device is ready.

CAUTION: Wear protective

gloves when handling plates.*

Trendsetter NEWS SA

Operator Operations and Maintenance

Operations

Turn on the output device 2

These operations are required for some of

the maintenance procedures listed below.

Turn off the output device 3

Reset the output device 8

Maintenance Work To

Be Done

How

Often

Date Work

Completed

Exterior surfaces Clean

Weekly

Load ramp 1Clean

Plate roller * 9Clean Monthly

Edge detection strips * 10 Clean Every three

months

Compressed air supply

ﬁ lters:

Six months

or as

needed

5 micron ﬁ lter * 4Replace

0.01 micron ﬁ lter * 5Replace

Intake air ﬁ lter * 7Replace

Universal Debris Removal

Cabinet (UDRC) ﬁ lter ** 6Replace As needed N/A

* Procedures for these items are included in this visual quick reference guide.

** Optional equipment—media dependent.

Note: This document is not intended as a substitute for the Trendsetter NEWS SA

Operator Guide. Refer to the operator guide for detailed procedures.

Software may display differently depending on the version of Print Console in use.

4 5

OFF

Optional

Trendsetter NEWS SA Replacing the Air Supply Filters

5 micron ﬁ lter 0.01 micron ﬁ lter

Air supply ﬁ lter kit

Part number 332-00003

2 Turn off the compressed air. 1

Replacing the 5 Micron Filter

Replacing the 0.01 Micron Filter

Turn off the compressed air.

Bowl

Tab

Unscrew the bowl by pulling the tab

down and turning the bowl to the left.

Remove the old ﬁ lter and

Install the new one.

4Clean inside the bowl.

5Replace the O-ring,

if necessary.

6Reattach the bowl by pushing

it up and turning it to the

right until it clicks. Turn on the compressed air.

90 psi

0.01 micron

ﬁ lter

4Clean inside the bowl.

5Replace the O-ring,

if necessary.

0 psi

5 micron

ﬁ lter

Unscrew the bowl by pulling the tab

down and turning the bowl to the left.

Tab

Bowl

0.01 micron

ﬁ lter

0.01 micron

6Reattach the bowl by pushing

it up and turning it to the

right until it clicks.

Remove the old ﬁ lter and

Install the new one.

* Refer to the Operator Guide for full details.

WARNING: Remove air pressure from the

device before replacing an air ﬁ lter.*

Trendsetter NEWS SA

Cleaning Inside the Output Device

Cleaning the Edge Detection Strip

Cleaning the Plate Roller

1To open the front panel:

a. In Print Console software, unlock

the front panel.

b. Rotate the two latches

and lift the front panel.

Rotate the drum to expose the two edge

detection strips.

Dampen a cloth with isopropanol and swipe it along

each strip once, in one direction only.

2 3

Locate the blue plate roller.

Dampen a cloth with water, and

slide the cloth over the plate roller.

To close the panels:

a. Pull down the front panel

and turn the locking latches.

b. Pull down the top panel

and then push on the two

corners to lock the internal

latches.

The top panel opens automatically.

Edge detection strips

* Refer to the Operator Guide for full details.

WARNING: Risk of electrical shock if liquids are

alowed to run freely into the output device.*

CAUTION: Be careful not to bump your head on

the raised panel.*

Trendsetter NEWS SA Replacing the Intake Air Filter

Remove the fan box panel:

a. Push the upper corners of the fan box panel

in until you hear both latches click.

b. Lift the fan box panel up and out.

Remove the old intake air ﬁ lter

from inside the fan box panel.

b. Push the upper corners of

the fan box panel in until

you hear both latches click.

Intake air ﬁ lter

Part number 55-0700

Fan box panel

Clean the intake air ﬁ lter frame. Install the new intake air ﬁ lter. Replace the fan box panel:

a. Lift the fan box panel and lower

it onto the locating pins.

Locating pin

Airﬂ ow arrows point inward.

3 4 5

Trendsetter NEWS SA

Removing a Flyoff

8 9

b. Rotate the two latches

and lift the front panel.

Rotate the drum to expose

the trailing-edge clamps.

Slide the trailing-edge clamps

off the plate.

Fold over the corners

of the plate.

Press the leading-edge

clamps to free the plate.

Clean out any debris

left behind.

In Print Console, click Resume.Reposition the trailing-edge clamps:

a. Align the trailing-edge clamps. b. Slide the trailing-edge

clamps into position.

* Refer to the Operator Guide for full details.

Open the front panel:

a. In Print Console software, unlock

the front panel.

3 4 5 6 7

The top panel opens

automatically.

In Print Console, click Resume.

10 Close the panels:

a. Pull down the front panel and rotate

the locking latches.

b. Pull down the top panel, and then push on

the two corners to lock the internal latches.

21 The device suspends activity.

CAUTION: Wear protective

gloves when handling plates.*

CREO PRODUCTS LABEL

FABRICATION DRAWING

PART NO.

SCALE

DOC

REV SHEET

SIZE

DRAWN BY

DATE

MILLIMETERS

UNLESS SPECIFIED

REV ECO DRAWING CHANGES BY

DATE APPROVED BY

2000:MAR:14

74-3260A A

WARNING STRONG MAGNETIC FIELDS

1) LABEL ADHESIVE: 3M 467 OR EQUIV.

2) MATERIAL: 3M 7980 MATERIAL

3) COLOUR: BLACK GRAPHICS ON BACKGROUND COLORS AS SHOWN

4) TOLERANCE: +/- 1mm

5) COMPUTER FILE AVAILABLE.

6) LABEL TO BE CSA APPROVED - VENDOR ID MARK REQUIRED.

1:1

G. BESTR. LEVASSEUR

A D394 2000:MAR:14 GREG BEST

LABEL SPECIFICATIONS

WARNING!

AVERTISSEMENT!

WARNUNG!

STRONG

MAGNETIC

FIELDS

STARKES

MAGNETFELD

74-3260A-A

YELLOW (PANTONE 108C)

BACKGROUND AND EXCLAMATION MARK

WHITE BACKGROUND

CHAMPS

MAGNETIQUE

INTENSE

LABEL SIZE: 26.0mm x 31.0mm

2mm Rad. corners, typ.

CAUTION: If you have an implanted

cardiac pacemaker, ensure that

magnetic clamps are kept more

than 7 cm (2.75 in.) away from the

pacemaker.*

Other Creo Printer manuals

Creo

Creo Trendsetter 400 User manual

Creo

Creo Trendsetter 3244+ AL User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide