Comeup Seal Gen2 9.5i User manual

Automotive Winch

Thank you for purchasing a Winch.This manual covers operation and maintenance

of the winch. All information in this publication is based on the latest production information available

at the time of printing. We reserve the right to make changes without notice because of continued

product improvement.

The winch has been designed to give safe and dependable service if operated according to the

instructions. Please read and understand this manual before installation and operation of the winch.

Careless winch operation can result in serious injury or property damage.

When requesting information or ordering replacement parts, always give the following information:

1. Winch model and voltage

2. Serial Number

3. Item. No. and Part Number

4. Part Description

1. The winch is a very powerful machine. Treat with extreme care and observe all caution and

warnings.

2. The winch is rated at the first layer of wire/synthetic rope on the drum for intermittent-periodic

duty.

3. The winch is not to be used to lift, support or otherwise transport personnel.

4. A minimum of five (5) wraps of steel wire rope and of ten (10) wraps of synthetic rope around the

drum is necessary to support the rated load.

5. Keep clear of winch, rope, hook, and fairlead while operating.

6. Wire/synthetic rope can break without warning. Always keep a safe distance from the winch and

rope while under a load

7. Failure to adequately align, support, or attach the winch to a suitable mounting base could result

in a loss of efficiency of performance or damage to the winch, wire/synthetic rope and mounting

channel.

WARNING

Control Indicator Guide

To prevent any serious injury, do not install or operate this winch before reading this manual. Keep

this manual with the winch at all times. Winch operators must read and understand contents fully.

Know the specific function of your winch.

1. Cutout Switch：

Your Seal Gen2 9.5i/9.5si /9.5rsi winches have a cutout switch

It is to activate or deactivate the winch.

The cutout switch could also cut out the battery draw of

wireless control models when the engine is not running.

2. Vehicle Battery Level：

The dash board of your Seal Gen2 9.5i/9.5si/9.5rsi winch is with

battery indicator to show the status of vehicle battery level.

Icon (Green):Fully charged around 12V level

Icon (Green):Fair charged around11V

Icon (Green):Fair charged around 10 V

Icon (Green):Low charged around 9V

Icon (Red): Extreme low below 8V

3. Cable in /out direction indicators：

The green triangle icons on the IDBfor your Seal Gen2 9.5i / 9.5si / 9.5rsi will indicate the rope

winding direction.

a. Cable in: The green triangle icons moved from the outside toward the center indicate the

rope winding-in direction.

b. Cable out: The green triangles icons moved from the center toward the outside indicate

the rope winding-out direction.

c. Over-heat: The green triangles icons will turn red if the motor is over-heating, but the

direction remains unchanged.

4. Over heat Protection：

There are three kinds of overheat protection warnings to protect the motor and control from

being damaged or personal injury：

a. IDB warning: The flashing red temperature icon on (IDB) of your Seal Gen2 9.5rsi winch

indicates the motor is over-heating.

b. Handheld remote warning: The two green LED indicators on the wired remote control

will turn red if the motor is over-heating.

c. Buzzer warning: When motor is over-heating, the Seal Gen2 9.5rs /9.5rsi /12.5rs will

induce an buzzer alarm

Control Indicator Guide

Temperature Warning Handheld Remote Warning Buzzer warning

5. Wireless Remote Control Icon：

a. While using wireless control, the wireless signal icon of IDB of your Seal Gen2 9.5rsi will turn

on.

b. The LED indicators on the wireless transmitter indicate the signal condition. If green, the

signal is good; red is weak.

Wireless Signal Icon Wireless Transmitter

6. Wireless transmitter’s battery life：

If green LED indicator on the wireless transmitter is flashing, the battery of the transmitter need

to be replaced.

uWireless Receiver & Transmitter Operation

This wireless remote control device complies with CE mark, FCC and Industry Canada (IC) rules.

CE Mark Warning

•This is a Class B product, in a domestic environment, this product may cause radio

interference, In which case the user may be required totake adequate measures.

FCC and Industry Canada (IC) Warning:

•This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Control Indicator Guide

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio / TV technician for help.

►There are four control modules of Sean Gen2 series winches. All are similar in setup, but

with differing responses in regards to their control type.

1). Seal Gen2 9.5rsi：

a. With both wireless and wire remote control.

b. IDB with wireless remote control function +cut out switch +temperature warning and

overheat buzzer warning.

c. After activating the winch, the logo LED will light on and battery indicator shows the status

of battery level.At the same time, the wireless remote control icon will be blinking with

buzzer warning until the remote control is tuned.

d. Cable in / out direction indicators.

2). Seal Gen2 9.5i / 9.5si：

a. With wired remote control.

b. IDB with wireless remote control function +cut out switch + temperature warning and

overheat buzzer warning.

c. Cable in / out direction indicators.

3). Seal Gen2 9.5rs：

a. With both wireless and wire remote control.

b. Overheating buzzer warning.

4). Seal Gen2 9.5 / 9.5s：

a. With wire remote control.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the

user's authority to operate the equipment.

Control Indicator Guide

►Seal Gen2 9.5rsi with IDB, cut out switch and buzzer warning.

1).Wireless remote control module：

Applicable models Seal Gen2 9.5rsi

LED & Buzzer

LOGO Transmitter

LED

Turn on

on on

Blinking

2 short

beeps for

1 minutes

Press Transmitter for 5 seconds X

Turn on

Green

Programming Blue

Long beeps

for

5 seconds

If programming failed , Winch will automatically use the previous programming after 1 minute.

Cable in / IDB LED (Green)

Red

Cable out / IDB LED (Green)

Motor

overheating

warning

(Blinking)

Cable in / IDB

LED (Red) 2 short

beeps

every

5 seconds

Cable out / IDB

LED (Red)

No operation

Light

Light on

Green

Low voltage on transmitter

Green

Poor signal warning Red

Press the power button for 5

seconds to turn transmitter off. X

Press the power button

to turn winch off. X X

Control Indicator Guide

2).Wired remote control module：

Applicable models Seal Gen2 9.5i / 9.5si / 9.5rsi

LED & Buzzer

LOGO

Remote

Control

LED

Press the power button

to turn winch on. Light

Light

Blinking

(remark 1.)

2 short

beeps for

1 minutes

(remark 2)

Plug in connector Green

Cable in / IDB LED (Green)

X Green

Cable out / IDB LED (Green)

Motor

overheating

warning

(Blinking)

Cable in / IDB

LED (Red) 2 short

beeps

every

5 seconds

Red

Cable out / IDB

LED (Red)

No operation Light

Light

Light on

(remark 3)

Press the power button

to turn winch off. X

Remarks:

1. Seal Gen2 9.5i / 9.5si: No wireless signal icon.

2. Seal Gen2 9.5i / 9.5si: Buzzer won’t be activated accordingly.

3. Seal Gen2 9.5rsi: Turn winch on, winch will automatically use the previous

programming.

Control Indicator Guide

3).Wireless remote control with wired remote control (2 LEDs on wired remote control

and buzzer in the control box), For Seal Gen2 9.5rs / 12.5rs only：

Applicable models

Seal Gen2 9.5rs / 12.5rs

LED & Buzzer

Buzzer Transmitter

LED

Remote

Control LED

Press the power button on

transmitter for 5 seconds to

turn transmitter on.

X Green X

Cable in / out operation

Red

Green

Motor

overheating

warning

Cable in / out

2 short beeps every

5 seconds

Red

No operation Green

Low voltage on transmitter X

Blinking

green

Poor signal warning

Blinking red

Press the power button of

transmitter for 5 seconds to

turn transmitter off.

X X X

4).Wired remote control (2 LEDs on remote control),

For Seal Gen2 9.5 / 9.5s / 12.5 / 12.5s only：

Applicable models

Seal Gen2 9.5 / 9.5s / 12.5 / 12.5s

LED & Buzzer

Buzzer LEDs on remote control

Plug in connector

Green

Cable in / out opperation

Green

Motor overheating warning X Red

Plug out connector

Control Indicator Guide

uPower in the winch (Getting started)

1. Cut out Switch：

Your Seal Gen2 9.5i / 9.5si / 9.5rsi winches can be activated by the cut out switch.

1.1 Press the cutout switch button to activate the winch operation. Verify a red light appears

around the button.

1.2 The white COMEUP winch logo icon will bright up for Seal Gen2 9.5i / 9.5si / 9.5rsi,

battery indicator icons will lighton in green.

1.3 The wireless control device is in tuning.

2. Hand-held switch：

All automotive winches are supplied with a wired remote control to activate and operate the

winch. Two green LEDs indicator the winch is under operation.

3. Wireless Transmitter：

Your Seal Gen2 9.5rs / 9.5rsi /12.5rs and optional wireless transmitter for other automotive

winches can be operated by wireless remote control.

Press and hold the power button for 5 seconds to activate winch operation. The green LED

Indicator lights up.

Hand-held Switch Wireless Transmitter

uBattery replacement

When the green LED Indicator is flashing indicates an extreme low battery level of wireless

transmitter’s.The battery should be replaced.

1. Loose the three screws from the back cover of the wireless transmitter.

2. Separate the top section and remove the old battery and dispose it.

Cutout Switch

LED Indicator

Power Button

Cable In

COMEUP Winch Logo

Winding Direction

Thermal Protection

Wireless SignalVehicle Battery Life

Cable Out

This manual suits for next models

Table of contents

Popular Winch manuals by other brands

WARRIOR

WARRIOR Trojan 40PUS12 Assembly & operating instructions

SVERO

SVERO 16 User instructions

Warrior Winches

Warrior Winches C10000NH owner's manual

Badland Winches

Badland Winches 68146 Installation and operating instructions

Bush

Bush II Series quick start guide

Badland

Badland APEX 5500 user manual

Quadratec

Quadratec Q9000 Synthetic Operator's guide

C-Max

C-Max VIGO Installation & operation manual

Orvea

Orvea Italwinch 805 Installation and user manual

Prowinch

Prowinch PWJTHF300 user manual

Clas Ohlson

Clas Ohlson LD2000-A manual

Topex

Topex 97X080 Instructions for use

Eastbound

Eastbound MotoWinch 1707001 operating instructions

Runva

Runva EWD8000 Assembly & operating instructions

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Parts, operation and maintenance manual

Granit

Granit 11157675 operating instructions

TREX

TREX TB75 user manual

Badland

Badland ZXR 2500 user manual