Code Alarm Professional ca5054 User manual

CCJCic~LA~m

~r::lOFESSIONA

SEr::liES

Remote Start with Keyless Entry

Installation Guide

ca5054

Table

Contents

Before

You

Begin.........................................................................................3

Wire Connection Guide...............................................................................4

7 Pin Main Harness ...................................................................................5

3 Pin Parking Light Harness......................................................................7

6 Pin Start Harness ...................................................................................7

4 Pin Alternate Harness.............................................................................9

2 Pin Door Lock Harness ........................................................................10

Additional Ports.........................................................................................14

Antenna I LED I Programming Port........................................................ 14

OBI

Port...................................................................................................14

Set Up &Programming .............................................................................15

Transmitter Programming........................................................................15

Manual Feature Programming................................................................. 15

Programming Feature Banks ..................................................................16

Tach Programming ..................................................................................18

Smart Tachless Mode..............................................................................19

Feature Descriptions.................................................................................19

Transmitter Button Functions ..................................................................26

Remote Start Shutdown Diagnostics ......................................................27

System Layout...........................................................................................28

2 ca5054 Install rev

BEFORE YOU BEGIN

FOR AUTOMATIC TRANSMISSION VEHICLES

ONLY.

. .

•

....

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Installation Precautions:

Roll down window to avoid locking keys

vehicle

during installation

Avoid mounting components or routing wires near

hot surfaces

Avoid mounting components or routing wires near

moving parts

Tape or loom wires under hood for protection and

appearance

Use grommets when routing wires through metal

surfaces

Use a Digital Multi Meter for testing and verifying

circuits. DO NOT USE A TEST LIGHT, OR

"COMPUTER SAFE PROBE" as these can set off air

bags or damage vehicle computers.

Technical

Support

(800) 421-3209

http://avxtech1.com

c..

,...._

(f)

zr-

-I

a..

('I)-

.....J

.....

a::

.....

(f)

z:::S:::

-(.)

a..

N.....J

7 Pin Main Harness

BLACK/WHITE ILLUMINATED ENTRY OUTPUT ( - )

BROWN/BLACK

HORN OUTPUT

(-)

RED/WHITE TRUNK

RELEASE

OUTPUT ( - )

BLUE/BLACK

START

STATUS

ACTIVE OUTPUT ( - )

PURPLE/WHITE TACH INPUT

GRAY

HOOD PIN INPUT

(-)

BROWN/RED

BRAKE

INPUT ( + )

3 Pin Parking Light Harness

BLACK GROUND

WHITE/RED PARKING LIGHT INPUT

WHITE

PARKING LIGHT

OUTPUT

6 Pin Start Harness

PURPLE STARTER

OUTPUT-

MOTOR SIDE

RED BATTERY 12V (

ORANGE ACCESSORY 1 ( + )

PINK/WHITE IGNITION 2 ( + )

RED/WHITE BATTERY 12V (

PINK IGNITION 1 ( + )

4 Pin Alternate Harness

BLACK/YELLOW PULSE DURING CRANK ( - )

GREEN/WHITE PULSE AFTER SHUTDOWN ( - )

LT BLUE FACTORY ARM

PULSE AFTER START

(-)

LT GREEN/BLACK FACTORY DISARM

PULSE BEFORE START ( - )

2 Pin Lock Harness

BLUE UNLOCK

(-)

GREEN LOCK

(-)

ca5054 Install rev A.

Main

H.arness

BLACK/WHITE ILLUMINATED ENTRY OUTPUT

(-)

This wire provides a ( - ) 200mA output for 30 seconds when the system

disarmed

capable

driving relays.

Locate the vehicle's dome light or pin switch wire.

Verification: This wire will register positive voltage or ground when the

vehicle's dome light

turned ON.

BROWN/BLACK HORN OUTPUT ( - )

Locate the vehicle's horn wire.

Verification: This wire will register at positive voltage and register

ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current

output, 200mA.

3 RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle's trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when

the trunk release is activated.

This is a low current output, 200mA and is configurable

option programming

4 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )

This wire provides a ( - ) 200mA output when the remote start function is activated

and remains

until4

seconds after the remote start is shutdown. If this wire will be

used for multiple application's a 1 amp diode is required in-line with the stripe facing

the control module.

PURPLE/WHITE TACH INPUT

Locate the vehicle's ignition coil

fuel injector

the engine compartment.

Verification:

Test using the following procedure:

Set voltmeter to AC VOLTS.

Attach positive lead

a volt meter to a constant 12-volt source.

Attach negative lead

a volt meter to the wire to be tested.

Start the engine.

Have someone press on the gas pedal slightly as you monitor the meter. If

connected to the correct wire, the voltage reading will increase as the engine's

RPM increases.

Connect the PURPLE/WHITE wire to the negative side

the vehicle ignition coil

fuel injector.

6 GRAY HOOD PIN INPUT

(-)

Install a Hood Pin Switch and connect to the GRAY wire. This connection is required

for Remote Start.

Verification:

This wire when connected will register ground when the

vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE:

Be sure to loom the wire, and seal the grommet.

BROWN/RED BRAKE

INPUT(+)

Locate the vehicle's brake light wire at the brake pedal mounted switch. This

connection is required for Remote Start.

Verification:

This wire registers positive voltage when the brake pedal is

pressed.

Connect the BROWN/RED wire to the vehicle's brake light wire.

ca5054 Install rev

3 Pin Parking Light Harness

1 BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and

selftapping screw (not supplied). Scrape away paint from the grounding point to

ensure a good connection. The recommended grounding point is a metal surface

the driver's side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

2 WHITE/RED PARKING LIGHT INPUT

WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification: This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a 15 Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

6 Pin Start Harness

PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage onlywhen the key is turned to the

START position.

Connect the PURPLE wire to the vehicle starter wire.

RED

BATTERY

12V

(

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification:

This wire will register ( + ) voltage

all positions

the ignition

switch.

Connect

the RED wire to the constant 12 Volt battery wire.

NOTE:

Remove

all fuses until all connections are made.

ORANGE

ACCESSORY

1 ( + )

Locate the vehicle's

accessory

wire

the ignition switch.

Verification:

This wire registers voltage

when

the key is turned to

ACC

(Accessory) and

the

ON (or

RUN)

position.

The

voltage

drops

out

when

the

key is turned to the START (or

CRANK)

position.

Connect

the

ORANGE

wire to the vehicle's accessory wire.

PINK/WHITE

IGNITION 2 (

+ )

Locate the vehicle's 2nd ignition wire

the ignition switch (if equipped).

Verification:

This wire registers voltage

when

the key is turned to the

(or

RUN) position, but not the

ACC

(Accessory) position.

The

voltage

does

not

drop

out

when

the key is turned to the START (or

CRANK)

position.

Connect

the

PINK/WHITE

wire to

the

vehicle's ignition 2 wire.

Programmable output:

IGN, ACC, Start.

RED/WHITE

BATTERY

12V

(

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification:

This wire will register ( + ) voltage in all positions

the ignition

switch.

Connect

the

RED/WHITE

wire to

the

constant 12 Volt battery wire.

NOTE:

Remove

all fuses until all connections are made.

ca5054 Install rev

6 PINK IGNITION 1 (

Locate the vehicle's ignition wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key is turned to the

START (or CRANK) position.

Connect the PINK wire to the vehicle's Ignition wire.

This wire is also used for Ignition 1 Output.

4 Pin Alternate Harness

1 BLACK/YELLOW PULSE DURING

CRANK

(-)

Locate the vehicle's second starter (crank) wire at the ignition switch. (if equipped)

Verification: This wire registers voltage only

the start (crank) position

the ignition switch.

This wire will supply a

(-)

200mA

output and can be configured

option

programming.

2 GREEN/WHITE PULSE

AFTER

SHUTDOWN ( - )

This wire will supply a ( - )

200mA

pulse after the remote start shuts down. This

is typically used to re-lock the vehicle's doors

they unlock upon remote start

shutdown. It can also be used to pulse a door pin-switch wire to prevent the vehicle's

accessories from remaining on after remote start shutdown.

This output is configurable

option programming.

BLUE FACTORYARM I

PULSE

AFTER

START ( - )

This wire will supply a ( - )

200mA

pulse both upon arming the system and upon

successful completion

the remote start activation sequence and is typically used to

re-lock the vehicle's doors upon remote start

necessary.

This output is configurable

option programming.

GREEN/BLACK FACTORY DISARM I

PULSE BEFORE START ( - )

This wire will supply a ( - ) 200mA pulse both upon disarming the system and when

the remote start feature is activated. Locate the factory perimeter alarm disarm wire

from the key cylinder inside the drivers door.

Verification: This wire registers ground ifthe key is turned to the unlock

position in the driver's door cylinder.

This output

conffgurable

option programming.

2 Pin Door Lock Harness

1 BLUE UNLOCK

(-)

2 GREEN LOCK

(-)

The door lock I unlock outputs are designed to control several different types

systems which may require additional parts. Please review the wire and location

chart to see which type

door lock system is

your vehicle. The most common

types are shown

the following diagrams.

These wires supply a

(-)

500mA output.

ca5054 Install rev

Other manuals for Professional ca5054

Table of contents

Other Code Alarm Remote Starter manuals

Code Alarm

Code Alarm ca5354 User manual

Code Alarm

Code Alarm CA 1055 User manual

Code Alarm

Code Alarm Professional Series CA 5050 User manual

Code Alarm

Code Alarm CSM-3 User manual

Code Alarm

Code Alarm ca5554 Professional series User manual

Code Alarm

Code Alarm Professional ca5054 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm CSM-3 User manual

Code Alarm

Code Alarm Professional Series CA 4050 User manual

Code Alarm

Code Alarm Professional Series CA 5050 User manual

Code Alarm

Code Alarm CA611 User manual

Code Alarm

Code Alarm ca 2051 User manual

Code Alarm

Code Alarm F40 User manual

Code Alarm

Code Alarm Elite ca6555E User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm ca4054 User manual

Code Alarm

Code Alarm PC 7400 User manual

Code Alarm

Code Alarm GUARDIAN CPL 100 User manual

Code Alarm

Code Alarm PC 4300 User manual

Code Alarm

Code Alarm CA-630 User manual

Code Alarm

Code Alarm CA-535 User manual

Code Alarm

Code Alarm SRT 9000 User manual

Code Alarm

Code Alarm SRT 6700 User manual

Code Alarm

Code Alarm CA 4055 User manual

Popular Remote Starter manuals by other brands

AstroStart

AstroStart 803U user manual

Durite

Durite 0-649-20 Leaflet

EINHELL

EINHELL BT-PS 1000 Directions for use

Linear

Linear ACCESS AK-21 Installation and programming instructions

Soundstream

Soundstream TARANTULA RS.2 installation guide

Jaycar Electronics

Jaycar Electronics MB3752 instruction manual

Ultra Start

Ultra Start 72 Series owner's manual

ADS

ADS FLASHLOGIC FLRSVW1 Product guide

Selecta

Selecta JS012 instruction manual

Black Widow Security

Black Widow Security BW RAS 400 installation manual

Vector

Vector Power City DK080706 Owner's manual & warranty

Ozito

Ozito OJS-800 instruction manual

Profi-Partner

Profi-Partner 46387 instruction manual

EZ STARTER

EZ STARTER EZ-45 user guide

Viper

Viper 4204 owner's guide

Essex Electronics

Essex Electronics KE-1701 user guide

EINHELL

EINHELL EGS 3600 Directions for use

Rooboost

Rooboost RB-1750WP user manual