Code Alarm Ca6554 User manual

CCJCc:~LA~m

i=)~OFESSIONAI

SE~IES

Security and Remote Start Installation Guide

for models:

ca6554

428592

Table

Contents

Before You Begin.........................................................................................4

Wire Connection Guide...............................................................................5

4 Pin Main Harness ...................................................................................7

6 Pin Start Harness ...................................................................................8

6 Pin Output Harness ..............................................................................10

8 Pin Input Harness.................................................................................

4 Pin Alternate Output Harness...............................................................14

4 Pin AUX Output Harness......................................................................15

3 Pin Door Lock Output Harness.............................................................16

AdditionaI Ports.........................................................................................

Antenna I LED I Programming Port........................................................20

OBI

Port...................................................................................................20

Telematic Interface Port...........................................................................20

Set Up &Programming .............................................................................

Transmitter Programming........................................................................

Manual Feature Programming.................................................................

Programming Feature Banks ..................................................................22

Tach

Programming ..................................................................................25

Smart Tachless Mode..............................................................................25

Adjusting the Shock Sensor ....................................................................26

Testing the Shock Sensor

........................................................................26

Chirp Delete -UserAccessible................................................................26

Dome Light Delay I Theater Dimming .....................................................26

2 ca6554 Install revA

Feature Descriptions.................................................................................

Transmitter Button Functions..................................................................

Security

TriggerZones..............................................................................

Remote

Start

Shutdown Diagnostics ......................................................

System

Layout

...........................................................................................

BEFoRE

YOU BEGIN

FOR AUTOMATIC TRANSMISSION VEHICLES ONLY.

•

PROFESSIONAL INSTALLATION

STRONGLY RECOMMENDED

Roll down window to avoid locking keys

vehicle

during installation

Avoid mounting components or routing wires near

hot surfaces

Avoid mounting components or routing wires near

moving parts

Tape or loom wires under hood for protection and

appearance

Use a Digital Multi Meter for testing and verifying

circuits. DO NOT USE A TEST LIGHT,

"COMPUTER SAFE PROBE" as these can set off air

bags

damage vehicle computers.

Technical Support

(BOO)

421-3209

http://avxtech1.com

ca6554 Install revA

WHITE/RED PARKING LIGHT INPUT

WHITE PARKING LIGHT OUTPUT

BLACK GROUND

.q-

BROWN SIREN OUTPUT (

+ )

PURPLE STARTER

OUTPUT-

MOTOR SIDE

RED BATTERY 12V (

ex:

ORANGE ACCESSORY 1 (

+ )

(/)

z PINK/WHITE IGNITION 2 ( + )

c:o

RED/WHITE BATTERY 12V (

PINK IGNITION 1 (

BROWN/BLACK HORN OUTPUT ( - )

BLUE/BLACK START STATUS

ACTIVE OUTPUT

(-)

::>

VIOLET/BLACK

AUX

1 OUTPUT

)

::>

RED/WHITE TRUNK RELEASE OUTPUT ( - )

c:o

LT GREEN/BLACK FACTORY DISARM

PULSE BEFORE START ( - )

ORANGE GROUND

WHEN

ARMED OUTPUT ( - )

::J

a..

x,_

=>::::>

<(a_

Zl-

-:::>

a..o

-(.)

a..

('t')_J

Input

Harness

BLUE/WHITE INSTANTTRIGGER INPUT ( - )

GREEN

DOOR

TRIGGER INPUT

)

PURPLE

DOOR

TRIGGER INPUT (

+ )

WHITE/BLUE

ExrRENAL

START

INPUT ( - )

GRAY

HOOD

PIN INPUT

(-)

GRAY/RED

PARKING

BRAKE

INPUT ( - )

BROWN/RED

BRAKE

INPUT ( + )

PURPLE/WHITE

TACH INPUT

··

···.·······

terriate

··.

Outp

·llt .

rness

BLACK/YELLOW PULSE DURING

CRANK

)

GREEN/WHITE PULSE

AFTER

SHUTDOWN

)

LT BLUE

FACTORY

ARM

PULSE

AFTER

START

(-)

LT GREEN/BLACK

FACTORY

DISARM

PULSE BEFORE

START

( - )

PINK/BLACK

AUX

5 OUTPUT ( - )

ORANGE/BLACK

AUX

OUTPUT

( - )

GRAY/BLACK

AUX

OUTPUT

( - )

WHITE/BLACK

AUX

OUTPUT

( - )

BLUE

UNLOCK

(-)

OPEN

GREEN

LOCK

(-)

ca6554 Install revA

Pln

Mail"l

Harness

WHITE/RED PARKING LIGHT INPUT

WHITE PARKING LIGHT OUTPUT

Locate the parking light output wire at the vehicle's light switch.

Verification:

This wire registers positive voltage when the parking lights are

turned on.

Positive switching Parking Lights:

Connect the WHITE/RED wire to a

Amp max fused battery source.

Connect the WHITE wire to the parking light output wire.

Negative switching Parking Lights:

Connect the WHITE/RED wire to a good chassis ground.

Connect the WHITE wire to the parking light output wire.

BLACK GROUND

Connect the BLACK wire to a solid chassis ground point using a ring terminal and

self tapping screw (not supplied). Scrape away paint from the grounding point to

ensure a good connection. The recommended grounding point is a metal surface

the driver's side kick panel area.

NOTE:

Do not ground the BLACK wire with any other vehicle components.

BROWN SIREN OUTPUT (

Locate a suitable mounting location

the engine compartment for the siren, away

from moving parts.

With the bell ofthe siren aiming downwards, secure the siren

place using self

tapping screws, being careful not do drill into any hoses, wiring or components.

Connect the BLACK siren wire to a chassis ground using a ring terminal and self

tapping screw (not supplied).

Route the BROWN siren output wire from the control module through the firewall and

connect to the RED wire on the siren.

NOTE:

Be sure to loom the siren wires, and seal the grommet.

1 PURPLE STARTER OUTPUT ( + )

Locate the vehicle starter wire.

Verification: This wire registers voltage onlywhen the key is turned to

the

START position. Cut the vehicle's starter wire

halfwhen installing

the

starter kill relay.

Verification afterstarter wire is cut:

KEY SIDE

starter wire registers voltage when the key is turned to

the

START position.

MOTOR SIDE

starter wire registers no voltage.

Connect the PURPLE wire to the vehicle starter wire, use the MOTOR SIDE

the

vehicle starter wire when installing the starter kill relay.

2 RED BATTERY 12V (

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification: This wire will register ( + ) voltage

all positions

the ignition

switch.

Connect the RED wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

3 ORANGE ACCESSORY 1 ( + )

Locate the vehicle's accessory wire at the ignition switch.

Verification: This wire registers voltage when the key is turned to

ACC

(Accessory) and the ON (or RUN) position. The voltage drops out

when

the

key is turned to the START (or CRANK) position.

Connect the ORANGE wire to the vehicle's accessory wire.

ca6554 Install revA

PINK/WHITE IGNITION 2 ( + )

Locate the vehicle's 2nd ignition wire at the ignition switch (if equipped).

Verification:

This wire registers voltage when the key is turned to the

(or

RUN) position, but not the ACC (Accessory) position. The voltage does not

drop out when the key is turned to the START (or CRANK) position.

Connect the PINK/WHITE wire to the vehicle's ignition 2 wire.

Programmable output: IGN, ACC, Start.

RED/WHITE BATTERY 12V (

Locate 1

the vehicle's constant 12 Volt battery wires at the ignition switch.

Verification:

This wire will register ( + ) voltage

all positions

the ignition

switch.

Connect the RED/WHITE wire to the constant 12 Volt battery wire.

NOTE: Remove all fuses until all connections are made.

PINK IGNITION 1 (

Locate the vehicle's ignition wire at the ignition switch.

Verification:

This wire registers voltage when the key is turned to the ON (or

RUN) position. The voltage does not drop out when the key

turned to the

START (or CRANK) position.

Connect the PINK wire to the vehicle's Ignition wire.

This wire is also used for Ignition 1 Output.

6 Pin

Output

Harness

BROWN/BLACK HORN OUTPUT ( - )

Locate the vehicle's horn wire.

Verification: This wire will register at positive voltage and register

ground when the horn switch is pressed.

Connect the BROWN/BLACK wire to the vehicle's horn wire. This is a low current

output, 200mA.

2 BLUE/BLACK START STATUS I ACTIVE OUTPUT ( - )

This wire provides a

(-)

200mA output when the remote start function is activated

and remains

until4

seconds after the remote start

shutdown. Ifthis wire will be

used for multiple application's a 1 amp diode

required in-line with the stripe facing

the control module.

VIOLET/BLACK AUX 1

This wire provides a

(-)

200mA output capable

driving relays. For Control

optional accessories (i.e. Power Window/Sunroof, etc.).

activate refer to the transmitter button configuration chart. Please refer to

the

selectable options for timing.

RED/WHITE TRUNK RELEASE OUTPUT ( - )

Locate the vehicle's trunk release wire at the trunk release switch.

Verification: This wire will register either positive voltage or ground when

the trunk release

activated.

This is a low current 200mA output and

configurable

option programming.

ca6554 Install revA

Other manuals for ca6554

Other Code Alarm Remote Starter manuals

Code Alarm

Code Alarm CA-550 User manual

Code Alarm

Code Alarm Professional Series CA 1050 User manual

Code Alarm

Code Alarm ca5554 Professional series User manual

Code Alarm

Code Alarm CA 521 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm SRT 9000 User manual

Code Alarm

Code Alarm CA611 User manual

Code Alarm

Code Alarm CA 5053 User manual

Code Alarm

Code Alarm PROFESSIONAL SERIES User manual

Code Alarm

Code Alarm SRT 6700 User manual

Code Alarm

Code Alarm CSI-100 User manual

Code Alarm

Code Alarm CA-630 User manual

Code Alarm

Code Alarm PC 4400 User manual

Code Alarm

Code Alarm ca5554 Professional series User manual

Code Alarm

Code Alarm F60 User manual

Code Alarm

Code Alarm ca5154 professional Series User manual

Code Alarm

Code Alarm CA-630 User manual

Code Alarm

Code Alarm CA 411 User manual

Code Alarm

Code Alarm CA-430 User manual

Code Alarm

Code Alarm CA-630 User manual

Code Alarm

Code Alarm Professional Series CA 4050 User manual

Code Alarm

Code Alarm ca6554 User manual

Code Alarm

Code Alarm ca4053 User manual

Code Alarm

Code Alarm PROFESSIONAL CASECRS User manual

Popular Remote Starter manuals by other brands

AstroStart

AstroStart 803U user manual

Durite

Durite 0-649-20 Leaflet

EINHELL

EINHELL BT-PS 1000 Directions for use

Linear

Linear ACCESS AK-21 Installation and programming instructions

Soundstream

Soundstream TARANTULA RS.2 installation guide

Jaycar Electronics

Jaycar Electronics MB3752 instruction manual

Ultra Start

Ultra Start 72 Series owner's manual

ADS

ADS FLASHLOGIC FLRSVW1 Product guide

Selecta

Selecta JS012 instruction manual

Black Widow Security

Black Widow Security BW RAS 400 installation manual

Vector

Vector Power City DK080706 Owner's manual & warranty

Ozito

Ozito OJS-800 instruction manual

Profi-Partner

Profi-Partner 46387 instruction manual

EZ STARTER

EZ STARTER EZ-45 user guide

Viper

Viper 4204 owner's guide

Essex Electronics

Essex Electronics KE-1701 user guide

EINHELL

EINHELL EGS 3600 Directions for use

Rooboost

Rooboost RB-1750WP user manual