Clarke CTJ2000LPB Instruction Manual

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1217 - ISS1

LOW PROFILE TROLLEY JACK

MODEL NO: CTJ2000LPB

PART NO: 7623067

INTRODUCTION

Thank you for purchasing this CLARKE trolley jack.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATION

Model number CTJ2000LPB

Length (exc handle): 560 mm

Width: 215 mm

Height of lifting cup (at rest): 90 mm

Maximum lifting height from floor: 380 mm

Distance raised perstroke (average): 6.5 mm

Weight: 12.9 kg

Pump Oil Capacity: 160-170 ml

Rated Capacity: 2 Tonnes

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

SAFETY PRECAUTIONS

1. This jack is for lifting only. Do not move a load using the jack as a dolly.

2. Do not use to lift people.

3. Always inspect the jack before use. Make sure that all parts are in good

condition and operating smoothly, and that no cracks or distortion is

apparent. If in doubt do not use. Have the damaged parts replaced or

consult your CLARKE dealer.

4. Make sure that the jack is on a firm level base, and there is no possibility of

it slipping when under load.

5. Make sure the load is taken by the full saddle and that the point of lift on

the load, is strong enough to support the load adequately.

6. Do not work under the raised vehicle until it is supported by suitable means

e.g. axle stands, NEVER rely on the jack to support the vehicle by itself.

7. Never push a load off the jack.

8. Ensure that all personnel are well clear of a load being raised or lowered.

9. Do not try to lift more then the rated load for the jack.

10. Do not use the jack if an oil leak is apparent. Consult your Clarke dealer.

11. Consult the vehicle handbook to determine the correct lifting points.

12. Always watch the jack and the load during operation.

13. Check the condition of the labels regularly and replace as required.

14. The jack must be maintained and repaired by suitably qualified persons.

15. Do not make any modifications to this jack or adjust any valves.

ENVIRONMENTAL PROTECTION

One of the most damaging sources of environmental pollution is oil products.

Never throw away used hydraulic oil with domestic refuse or flush it down a

sink or drain. Collect any hydraulic oil in a leak proof container and take it to

your local waste disposal site.

If disposing of this product or any damaged components, do not dispose of

with general waste. This product contains valuable raw materials and should

be taken to your local civic amenity site for recycling of metal products.

WARNING: THE OPERATOR MUST FOLLOW ALL INSTRUCTIONS WITHIN THIS

INSTRUCTION BOOKLET

BEFORE USE

1. Before use, attach the lifting

handle by clipping it over the two

large nuts at the main arm pivot.

2. Fit the rubber puck on the saddle.

3. Inspect the jack for oil leaks or any

other sign of damage. Should any

be apparent, have the jack

repaired by a qualified technician.

4. Check the piston for dirt, rust etc

which can damage the piston and

internal components.

5. Inspect the jack for distortion of components and security of all nuts and

bolts. If in doubt, do not use. Have damaged parts repaired or replaced. If

necessary, consult your CLARKE dealer.

The jack is now ready to use.

OPERATION

1. Ensure the vehicle to be raised is stable and on firm level ground with the

wheels chocked.

NOTE: The jack may move slightly during operation. It is important

therefore, that the floor is clean and completely free from debris.

2. Position the jack so that the

saddle is directly beneath the

lifting point.

• Consult the vehicle handbook

to determine suitable lifting

points.

3. Place the operating lever over the

release valve and turn it fully

clockwise to close the valve.

WARNING: NEVER WORK ON THE VEHICLE WHEN SUPPORTED ONLY BY A

JACK. THIS IS HIGHLY DANGEROUS. THE VEHICLE MUST BE SUPPORTED ON

AXLE STANDS OR SUITABLE SUPPORTS BENEATH THE CORRECT JACKING/

SUPPORT POINTS.

4. Fit the operating lever into the jacking port and pump the operating lever

to raise the saddle until it reaches the jacking point.

5. Make sure that the saddle is in full contact with the lifting point and that

there is nothing that will prevent a clean lift. Keep all personnel at a safe

distance before lifting.

6. Pump the operating lever to raise the vehicle to the required level.

NOTE: If, at any time, the jack feels spongy, follow the bleeding

procedure under Maintenance.

7. Position suitable, good quality axle stands directly beneath the supporting

points on the vehicle. Place the operating lever over the release valve and

very gently twist anti-clockwise to lower the load onto the stands.

8. Check constantly, preferably with an assistant, that the vehicle is resting

correctly on the axle stands and that the stands are stable before the

weight is taken.

9. Ensure that the axle stands cannot move when supporting the load.

10. To stop it lowering at any point, turn the operating lever clockwise again.

Always avoid a rapid descent by turning the operating lever slowly.

NOTE: Ensure this is carried out under complete control. DO NOT allow

the load to drop suddenly as this could damage internal parts.

11. Completely remove the jack from the vehicle.

MAINTENANCE

CHECKING THE OIL LEVEL

1. Ensure the jack is fully lowered by

turning the release valve fully anti-

clockwise.

2. Remove the cover plate and filler

plug.

• The oil should be almost level

with the bottom of the filler hole

• Oil can be topped up using

Clarke Hydraulic Oil (p/n

3050830 1 litre).

3. Replace the filler plug/cover plate and bleed any air from the system.

BLEEDING AIR FROM THE SYSTEM

1. Use the operating lever to turn the release valve anti-clockwise, relieving

pressure inside the jack.

2. Pump the operating lever several times to purge air from the system.

3. Turn the release valve clockwise and test the jack. If efficiency is still low,

check the oil level as described.

4. Wipe up any oil spillage and dispose of old/spilled oil appropriately.

TROUBLESHOOTING

If any of these remedies fail to restore your jack, consult your Clarke dealer.

SPARE PARTS

The Operating Lever, Rubber Puck, Rear Castor assembly are available as user

serviceable parts from your Clarke dealer, or Clarke International Parts

Department.

PROBLEM CAUSE SOLUTION

Jack will not lift the

rated load

Low oil level Check for leakage and top up

if required.

Release valve not

closed

Turn release knob fully

clockwise.

Air in the hydraulic ram Purge of air as on page 4.

Jack lowers when

under load

Release valve not fully

closed

Turn the release knob fully

clockwise.

Air in the hydraulic ram Purge of air as on page 4.

Pump feels spongy Low oil level Check for leakage and top up

if required.

Air in the system Purge of air as on page 4.

Handle raises or flies

back under load

Air in the hydraulic ram Purge of air as on page 4.

Jack will not lift full

height

Low oil level Check for leakage and top up

if required.

Air in the hydraulic ram Purge of air as on page 4.

Jack will not lower

completely

Return spring may be

faulty.

Return to your Clarke dealer for

repair.

DECLARATION OF CONFORMITY

This manual suits for next models

Table of contents

Other Clarke Jack manuals

Clarke

Clarke STRONG-ARM CTJ3GLC User manual

Clarke

Clarke CAX2TA User manual

Clarke

Clarke STRONG-ARM CTJ3000G Instruction Manual

Clarke

Clarke Strong-Arm CTJ2500QLP Instruction Manual

Clarke

Clarke CFTJ500 Troubleshooting guide

Clarke

Clarke STRONG-ARM CTJ2QLP Instruction Manual

Clarke

Clarke Strong-Arm CTJ4000G Instruction Manual

Clarke

Clarke CTJ2001G Instruction Manual

Clarke

Clarke CTBJ5 Troubleshooting guide

Clarke

Clarke CGK4 User manual

Clarke

Clarke Strong-Arm CTJ100 Installation and operation manual

Clarke

Clarke CTJ2000G User manual

Clarke

Clarke STRONG-ARM VPJ300 Installation and operation manual

Clarke

Clarke STRONG-ARM VPJ300 User manual

Clarke

Clarke Strong-Arm CTJ2250Q Instruction Manual

Clarke

Clarke STRONG-ARM CTJ3LQLPRO Installation and operation manual

Clarke

Clarke STRONG-ARM CTJ2GLC User manual

Clarke

Clarke CBJ32 Instruction Manual

Clarke

Clarke CTJ2500QLG Installation and operation manual

Clarke

Clarke CTJ3QLGB Instruction Manual

Clarke

Clarke CTJ3000C Instruction Manual

Clarke

Clarke CTJ1250AC Instruction Manual

Clarke

Clarke CFJ60 User manual

Clarke

Clarke STRONG-ARM CTJ10GLB Instruction Manual

Popular Jack manuals by other brands

Omega Lift Equipment

Omega Lift Equipment 18122C Operating instructions & parts manual

Pittsburgh

Pittsburgh 58816 Owner's manual & safety instructions

Unimec

Unimec TP Assembly instructions

Sonic

Sonic 4800703 instructions

BGS technic

BGS technic 70039 instruction manual

TradeQuip

TradeQuip 1128T owner's manual

VEVOR

VEVOR TJD-12000SP-F quick start guide

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK operating instructions

Stels

Stels 51131 user manual

Bushranger

Bushranger RJX01 instruction manual

Valex

Valex 1650520 Translation of the original instructions

Pfaff

Pfaff Merkur M0 Operating instruction

Beta

Beta 3050/K Operation manual and instructions

Sealey

Sealey 1050CXHV manual

Jung

Jung JH Series operating instructions

URIAH

URIAH UC200020 quick start guide

Kennedy

Kennedy KSJ010 instruction manual

Grizzly

Grizzly H8097 quick start guide