Clarke CAX2TA User manual

INSTRUCTIONS

GC0119 - ISS 2

MODEL NO: CAX2TA

PART NO: 7600010

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS

For your own safety and that of others around you, please read and observe

these safety instructions.

A warning label is attached to each stand and should be replaced if it is

removed or damaged. A replacement label can be obtained from your

Clarke dealer.

The following precautions are for guidance only. If you are in any doubt about

the use of these stands, please contact the Clarke International Service

Department for advice.

1. ALWAYS refer to the vehicle manufacturer’s instructions before raising the

vehicle.

2. ALWAYS ensure the working area is safe, i.e. not on the highway etc.

3. Do not use the axle stands on uneven ground.

4. ALWAYS ensure the vehicle is securely chocked before use.

5. ALWAYS ensure, before laying underneath the vehicle, a responsible person

is made aware in case of injury or accident.

6. ALWAYS ensure it is not possible under any circumstances, for the vehicle to

move, before getting underneath the vehicle.

7. NEVER allow children or animals to play in or near the area.

8. NEVER leave the vehicle on axle stands where it could be considered a

hazard to others.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

9. Do not overload the stands.

10. Never use more than a single pair of stands.

11. Only use on a hard level surface e.g. concrete.

12. Securely chock wheels remaining on the ground.

13. Make sure that each stand is securely located under a strong point on the

vehicle; consult the user’s handbook for guidance.

14. Lower the vehicle onto the stands slowly and gently.

15. Exercise extra care when using with a three wheeled vehicle or trailer.

16. Upper and lower columns are to be used only as a pair supplied.

17. It must be ensured that the vehicle/load is carefully located on the centre

of the axle stand saddle. Failure to do this can result in damage to the axle

stands, loss of support to the load, serious personal injury or loss of life.

ASSEMBLY

1. Slide the column into the base as

shown.

• If required remove the bolt (2) in

the base.

2. Slide the bolt into position and

secure using the nut supplied.

USING THE AXLE STANDS

1. Remove the locking pin.

2. Adjust the height of the axle stand.

3. Replace the locking pin.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATION

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Maximum Height 390 mm

Minimum Height 265 mm

Maximum Load 3 Tonnes per pair (1.5 tonnes each)

Product Weight 4.4 kg

This manual suits for next models

Table of contents

Other Clarke Jack manuals

Clarke

Clarke CTJ2500QLG Installation and operation manual

Clarke

Clarke Strong-Arm CTJ100 Installation and operation manual

Clarke

Clarke CTJ2500SUV Instruction Manual

Clarke

Clarke Strong Arm CTJ1250AB Installation and operation manual

Clarke

Clarke CTJ3GLS Instruction Manual

Clarke

Clarke Strong-Arm CTJ2500QLP Instruction Manual

Clarke

Clarke CTT320 User manual

Clarke

Clarke Strong-Arm CTJ2250LP Instruction Manual

Clarke

Clarke Strong-Arm CBJ2B Troubleshooting guide

Clarke

Clarke STRONG-ARM CTJ2QLP Instruction Manual

Clarke

Clarke CTJ2000LPB Instruction Manual

Clarke

Clarke Strong-Arm CTJ1500QULP Instruction Manual

Clarke

Clarke STRONG-ARM CTJ1500QL Installation and operation manual

Clarke

Clarke CBJ32 Instruction Manual

Clarke

Clarke CFTJ500 Troubleshooting guide

Clarke

Clarke CFJ48 Installation and operation manual

Clarke

Clarke Strong-Arm CTJ 50 Installation and operation manual

Clarke

Clarke CTJ2000LP Instruction Manual

Clarke

Clarke CTJ30 Troubleshooting guide

Clarke

Clarke STRONG-ARM CTJ5GLB Instruction Manual

Clarke

Clarke CTJ10GLS Instruction Manual

Clarke

Clarke STRONG-ARM CTJ3LQLPRO Installation and operation manual

Clarke

Clarke CTJ2000G User manual

Clarke

Clarke CTJ1800A Instruction Manual

Popular Jack manuals by other brands

Omega Lift Equipment

Omega Lift Equipment 18122C Operating instructions & parts manual

Pittsburgh

Pittsburgh 58816 Owner's manual & safety instructions

Unimec

Unimec TP Assembly instructions

Sonic

Sonic 4800703 instructions

BGS technic

BGS technic 70039 instruction manual

TradeQuip

TradeQuip 1128T owner's manual

VEVOR

VEVOR TJD-12000SP-F quick start guide

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK operating instructions

Stels

Stels 51131 user manual

Bushranger

Bushranger RJX01 instruction manual

Valex

Valex 1650520 Translation of the original instructions

Pfaff

Pfaff Merkur M0 Operating instruction

Beta

Beta 3050/K Operation manual and instructions

Sealey

Sealey 1050CXHV manual

Jung

Jung JH Series operating instructions

URIAH

URIAH UC200020 quick start guide

Kennedy

Kennedy KSJ010 instruction manual

Grizzly

Grizzly H8097 quick start guide