Cisco 2000 Series Manual
1
Cisco 2000 Series Hardware Installation
Cisco 2000 Series Hardware Installation
Following is the information required to install the router chassis.
About This Guide
Follow this procedural path to install your router:
1Install the router hardware using the procedures described in this publication.
2After the hardware is installed, refer the Router Products Getting Started Guide or
to the appropriate software publication to configure the router.
3Refer to the “Reference” section in this publication for cabling and basic
troubleshooting information.
Installation
This section guides you through the installation of the router and includes information
on safety, inspecting the system, preventing electrostatic discharge (ESD) damage,
tools and parts required, rack mounting, wall mounting, and making external cable
connections.
Note If you have questions about agency approvals, basic troubleshooting, system
specifications, or specific cable pinout information, review the information in the
section “Reference” on page 9.
Safety Recommendations
Follow these guidelines to ensure general safety:
•Keep the router area clear and dust-free during and after installation.
•Put the removed router cover in a safe place.
•Keep tools away from walk areas where you and others could trip over them.
•Do not wear loose clothing that could get caught in the router chassis. Fasten your
tie or scarf and sleeves.
•Wear safety glasses when working under any conditions that might be hazardous to
your eyes.
•Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.
2
Installation
Warning Before working on equipment that is connected to power lines,
remove jewelry (including rings, necklaces, and watches). Metal objects will
heat up when connected to power and ground and can cause serious burns or
weld the metal object to the terminals.
•Locate the emergency power-off switch in the room in which you are working.
Then, if an electrical accident occurs, you can act quickly to shut the power off.
•Before working on the system, turn off the power and unplug the power cord.
•Disconnect all power before doing the following:
—Installing or removing a router
—Working near power supplies
—Performing a software upgrade
•Do not work alone when potentially hazardous conditions exist.
•Never assume that power has been disconnected from a circuit. Always check.
•Look carefully for possible hazards in your work area, such as moist floors,
ungrounded power extension cables, and missing safety grounds.
•If an electrical accident occurs, proceed as follows:
—Use caution; do not become a victim yourself.
—Turn off power to the system.
—If possible, send another person to get medical aid. Otherwise, assess the
condition of the victim and then call for help.
—Determine if the person needs rescue breathing or external cardiac
compressions; then take appropriate action.
Inspecting the System
Do not unpack the router until you are prepared to install it. If the final installation site
will not be ready for some time, keep the router in the shipping container to prevent
accidental damage. When you have determined where you want the router installed,
proceed with the unpacking. The router, cables, publications, and any optional
equipment you ordered might be shipped in more than one container. When you
unpack each shipping container, check the packing list to ensure that you received all
of the following items:
•Router
•6-foot (1.8-meter) power cord
3
Installation
•Optional equipment (which might include network connection cables)
•A warranty card, a service and support card, and optional companion publications
as specified by your order
Inspect all items for shipping damage. If anything appears damaged, or if you
encounter problems when installing or configuring your system, contact a service
representative.
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It
occurs when electronic printed circuit cards are improperly handled and can result in
complete or intermittent failures. Always follow ESD prevention procedures when
removing and replacing cards. Ensure that the router chassis is electrically connected
to earth ground. Wear an ESD wrist strap, ensuring that it makes good skin contact.
Connect the clip to an unpainted chassis frame surface to safely channel unwanted
ESD voltages to ground. To properly guard against ESD damage and shocks, the wrist
strap and cord must operate effectively. If no wrist strap is available, ground yourself
by touching the metal part of the chassis.
Caution For safety, periodically check the resistance value of the antistatic
strap, which should be within the range of 1 and 10 Mohms.
Tools and Parts Required
Following are the tools and parts required to install the router:
•Screwdrivers:
—No. 1 Phillips
—Small, 3/16" (0.476 cm), and medium, 1/4" (0.625 cm), flat-blade
•ESD-preventive wrist strap
•Optional rack-mount/wall-mount kit (with documentation)
•One interface cable for each interface you require
In addition, you might need the following additional external equipment:
•Rack- and wall-mount brackets, fasteners, and instructions
•Channel service unit/digital service unit (CSU/DSU) for the serial interfaces
•Ethernet transceiver
•Token Ring media attachment unit (MAU)
4
Installation
•Modem for remote configuration (if required)
•Console terminal (configured for 9600 baud, 8 data bits, no parity, and 2 stop bits)
if future reconfiguration is desired
Information on Mounting the Router on a Rack or Wall
Rack and wall mounting procedures are described in a separate publication included
with the optional rack mount kit. If you intend to rack mount the router, do so before
making the external connections.
Preparing for External Connections
Following are the procedures for making external connections to the router. Figure 1
shows the rear panel of the router with the following connectors:
•Ethernet DB-15 (2102) or Token Ring DB-9 (2202)
•Serial DB-50 (1)
•Console RS-232
•Auxiliary RS-232
•AC power cable
Figure 1 Router Front and Rear View—Models 2102 and 2202
Ethernet port
Power On/Off switch
AUX port (DB-25)
Console port
(DB-25)
Serial port
System OK light
OK ETHERNET SERIAL
Interface activity
indicator lights
OK TOKEN RING SERIAL
Power On/Off switchConsole port (DB-25)
Token
Ring
port
AUX
port
(DB-25)
Serial (V2)
port
H1958
2102
2202
System OK light Interface activity
indicator lights
5
Installation
Information for United Kingdom Use Only
Cisco Systems declaration of operating conditions:
The Cisco 2000 is designed to meet the requirements of NET1 and NET2.
Warnings
Interconnection directly, or by way of other apparatus, of ports marked:
“Safety Warning — See instructions for use”
with ports marked or not so marked may produce hazardous conditions on the network
and that advice should be obtained from a competent engineer before such a
connection is made.
The ports marked “Ethernet,” “Token Ring,” “Console,” and “AUX” have a safety
warning applied to them as follows:
“These ports do not provide isolation sufficient to satisfy the requirement of BS6301;
apparatus connected to these ports should either have been approved to BS6301 or
have previously been evaluated against British Telecommunications plc (Post Office)
Technical Guides 2 or 26 and given permission to attach; any that other usage will
invalidate any approval given to this apparatus.”
Connection of Power Supply. The Cisco 2000 is intended for use when supplied with
power from a supply providing 220-240 VAC, 50/60 Hz up to 5 Amps.
Other usage will invalidate any approval given to this apparatus if as a result it ceases
to comply with BS6301: 1989.
The Cisco 2000 is brought into service by the supplier.
Information for European Community Use Only
The ports marked “Ethernet,” “Token Ring,” “Console,” and “AUX” are SELV
circuits. SELV circuits should only be connected to other SELV circuits.
6
Installation
Making External Connections
Follow these steps to make external connections to your router:
Step 1 Connect the Ethernet port to the network as shown in Figure 2.
Figure 2 Ethernet Transition Cable Connections
Step 2 Extend the Ethernet cable as shown in Figure 3.
Figure 3 Extending the Transition Cable from the Router’s Ethernet Port
Router
(top view)
Ethernet port
DB-15 connector
(with jackscrews)
H1892
18" (46 cm) transition cable
Rear
Slide-latch
connector
Transceiver
Router
(top view)
18" (46 cm) transition cable
Transceiver
Additional cable extension
up to 164' (50 m)
(not supplied)
H1903
Rear
7
Installation
Step 3 Connect the Token Ring port to the network as shown in Figure 4.
Figure 4 Token Ring Cable Connections
Step 4 Connect the serial ports to the network as shown in Figure 5.
Figure 5 Serial Cable Connections
Step 5 Connect the console and auxiliary ports as required for your method of
configuration. Your terminal should be configured for 9600 baud, 8 data bits,
no parity, and 1 stop bits.
Step 6 Connect the power cable between the router and the AC source.
Router
(top view)
DB-9 Token Ring
port connector
H1904
Media
attachment
unit
(MAU)
Back
Standard
IEEE 802.5
connectorToken Ring lobe cable
(not supplied)
Modem
or
CSU/DSU
H1905
Router
(top view)
Serial transition cable
EIA/TIA-232, EIA/TIA-449,V.35,
X.21, or EIA-530 connector
Serial port connector
Rear
8
Installation
What to Do after the Router Hardware Is Installed
After the router hardware is installed, the system is ready to be powered on and
configured. For software configuration information, refer to the following
publications:
•Router Products Getting Started Guide, Router Products Configuration Guide and
Router Products Command Summary
•Cisco 2000 Quick-Start Guide (as needed)
•Troubleshooting Internetworking Systems (as needed)
To order these or additional associated publications, refer to the Service and Support
card that accompanied your router.
9
Reference
Reference
This section includes the following reference information:
•Troubleshooting information
•System specifications
•Cable pinouts
Note For additional information on the Cisco 2000 router, refer to the Cisco 2000
Quick-Start Guide. For information on installing the router hardware, refer to the
section “Installation” on page 1 of this publication.
Troubleshooting
The key to problem solving in this system is to try to isolate the problem to a specific
subsystem. By comparing what the system is doing to what it should be doing, the task
of isolating a problem is greatly simplified.
Check the following items to help isolate the problem:
•With the power switch on and system LEDs on, does the fan operate? If no, suspect
the fan or the 12-volt (V) power supply.
•Does the system shut down after being on a short time?
—Suspect a thermal-induced shutdown.
—Ensure that the chassis intake and exhaust vents are clear.
—Suspect a power supply failure.
•System does not boot up, but System OK LED is on: suspect the 12V power supply.
•System partially boots, but System OK LED is not on: suspect a 5V power supply
failure.
The System OK LED should be on after the system initializes correctly. (See Figure 1.)
Note If an interface is extremely busy, the corresponding LED will be on all the time.
10
Reference
System Specifications
Following are the specifications for the router system.
Table 1 System Specifications
Cable Pinouts
The following tables list the pinouts for the cables that can be used with the router:
•Console asynchronous serial port, Table 2, on page 11
•Auxiliary asynchronous serial port, Table 3, on page 11
•EIA-530 synchronous serial DTE, Table 4, on page 12
•RS-232 synchronous serial DTE, Table 5, on page 14
•RS-449 synchronous serial DTE, Table 6, on page 15
•V.35 synchronous serial DTE, Table 7, on page 16
1. AUI = Attachment unit interface.
Description Design Specification
Dimensions H x W x D 13" x 14" x 4" (33 x 35.6 x 10 cm)
Weight 15 lb (6.8 kg)
Input voltage, frequency,
and power dissipation 110/220 VAC at 50 through 60 Hz
55W (max.)
273 Btu/hr
Processor Motorola 68EC030—20 MHz
Memory 1-MB primary memory
512-KB shared memory
32-KB nonvolatile configuration RAM
Network interface options 1 Ethernet and 1 synchronous serial (2102)
or 1 Token Ring and 1 synchronous serial (2202)
Ethernet interfaces AUI1IEEE 802.3 (DB-15)
Token Ring IEEE 802.5 (DB-9)
Synchronous serial interfaces RS-232, RS-449, V.35, X.21, EIA-530
Console port Asynchronous RS-232 DB-25 female connector
Auxiliary port Asynchronous RS-232 DB-25 male connector
Operating environment 32 to 104
°
F (0 to 40°C )
Nonoperating temperature –40 to 185°F (–40 to 85°C)
Operating humidity 5 to 95%, noncondensing
Noise level 40 dBa
This manual suits for next models
2
Table of contents
Other Cisco Wireless Router manuals
Cisco
Cisco BEFW11S4 Operation manual
Cisco
Cisco ASR 9000 Series User manual
Cisco
Cisco WRT610N - Simultaneous Dual-N Band Wireless... User manual
Cisco
Cisco WRT320N - Wireless-N Gigabit Router Wireless User manual
Cisco
Cisco cBR 8 User manual
Cisco
Cisco Linksys E900 User manual
Cisco
Cisco LINKSYS WRT54GX4 User manual
Cisco
Cisco Linksys WRV54G User manual
Cisco
Cisco WRVS4400N - Small Business Wireless-N Gigabit Security... Instruction Manual
Cisco
Cisco Linksys E900 User manual
Cisco
Cisco Linksys E4200 User manual
Cisco
Cisco RV180 Instruction Manual
Cisco
Cisco Linksys SE1500 User manual
Cisco
Cisco 7600 SIP 200 - SPA Interface Processor 200 Manual
Cisco
Cisco Catalyst IR1800 Rugged Series User manual
Cisco
Cisco Linksys E1000 User manual
Cisco
Cisco Linksys X1000 User manual
Cisco
Cisco UBR7225VXR Manual
Cisco
Cisco Small Business RV315W Instruction Manual
Cisco
Cisco Linksys E3000 User manual
