Cisco Meraki MR12 User manual

Assigning Static IP Addresses to an MR12 or MR58

The MR12 and MR58 wireless access points have two Ethernet ports that can be used to connect the device to a wired network. However, a static IP can only

be set on the primary Ethernet interface.

This article will discuss:

• Identifying the primary Ethernet port

• Behavior differences between primary and secondary ports

• Determining which port is being used

•Assigning a static IP

Identifying the Primary Ethernet Port

MR12

The primary Ethernet port is directly adjacent to the power connector and is labeled as Uplink.

MR58

The primary Ethernet port is located on the bottom-left side of the AP and is labeled as ETH0.

Behavior differences between primary and secondary ports

Primary (Ethernet 0)

This interface is capable of receiving power using PoE and can be assigned a static IP address. It is also capable of 10/100/1000Mbps speeds. It is intended for

connecting the MR12 to the rest of the network.

Secondary (Ethernet 1)

This interface can only receive an IP from DHCP and is not able to receive power using PoE. It is only capable of 10/100 speeds. It is still able to connect to the

Meraki Cloud Controller if the Primary connection is down, but is intended for used by a wired client. To allow use by a wired client, please refer to our

documentation regarding Extending the LAN with a Wireless Mesh Link.

Determining which port is being used

The simplest way to determine which port is being used is to physically look at the device, and refer to the diagrams above. If you are not near the device, the

easiest way to determine if the secondary port is being used is by looking at the AP Dashboard. Navigate to Monitor > Access points and click the AP in

question. Look under Status for LAN IP #. If the # = 1, then the AP is connected using the primary port. If # = 2, then the AP is connected using its secondary

port.

Assigning a static IP

A static IP can be assigned to the AP's primary interface in two ways.

Dashboard

1. In Dashboard, go to Monitor > Access points and select the AP in question.

2. Click the Edit icon.

3. On the page that appears, next to IP type select Static IP.

4. Enter the appropriate settings and click Save.

Local web interface

Refer to the MR Quick Start Guide for instructions on how to set the IP address using the local web interface.

This manual suits for next models

Table of contents

Other Cisco Wireless Access Point manuals

Cisco

Cisco FM PONTE-50 Manual

Cisco

Cisco Small Business AP541N User manual

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Meraki GR10 User manual

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... User manual

Cisco

Cisco Meraki MR36-HW Manual

Cisco

Cisco Catalyst IW9167E Manual

Cisco

Cisco MR18 User manual

Cisco

Cisco Aironet 1250 Series User manual

Cisco

Cisco Meraki MR33 User manual

Cisco

Cisco Catalyst 9124AX Series Manual

Cisco

Cisco AT&T U-VERSE VEN401 User manual

Cisco

Cisco Linksys Wireless-G WBP54GV2 User manual

Cisco

Cisco MERAKI MR44 User manual

Cisco

Cisco Wap581 User manual

Cisco

Cisco Meraki MR45 User manual

Cisco

Cisco Aironet Wave 2 Installation manual

Cisco

Cisco 500 Series Operator's manual

Cisco

Cisco aironet 1522 Guide

Cisco

Cisco WAP131 User manual

Cisco

Cisco Meraki MR42 User manual

Cisco

Cisco Aironet 1140 Series User manual

Cisco

Cisco IW3702 User manual

Cisco

Cisco Catalyst IW9165E User manual

Popular Wireless Access Point manuals by other brands

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Quick installation guide

Ubiquiti

Ubiquiti NanoStation NSM2 quick start guide

Aruba

Aruba IAP-335 user guide

Advantek Networks

Advantek Networks AWN-AP-54MR user manual

IP-COM

IP-COM AP355 user guide

Buffalo

Buffalo AirStation WLA-L11G user manual

EnGenius

EnGenius EnStationACv2 user manual

D-Link

D-Link DAP-3662 Quick installation guide

xG Technology

xG Technology xMax CN1300 installation guide

Widelink

Widelink ezWave WAP-1100 Series user guide

Edimax

Edimax CAP1200 user manual

Ubiquiti

Ubiquiti LBE-5AC-Gen2 quick start guide

Aruba

Aruba AP-203R installation guide

LuXout Shades

LuXout Shades LUXSHADE MOTION manual

CreatComm

CreatComm TB5F user manual

SineDigital

SineDigital MW-1500AP(H) installation guide

TP-Link

TP-Link AP9650 V1 Quick installation guide

Draytek

Draytek VIGORAP 902 user guide