Cisco WAP131 User manual

Other manuals for WAP131

3

Table of contents

Other Cisco Wireless Access Point manuals

Cisco

Cisco aironet 1522 Guide

Cisco

Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... User manual

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco Aironet 1240AG Series Manual

Cisco

Cisco ASA 5506-X User manual

Cisco

Cisco Meraki MR42E User manual

Cisco

Cisco WAP131 User manual

Cisco

Cisco WAP571 User manual

Cisco

Cisco AIR-AP1220B-A-K9 - Aironet 1200 - Wireless Access... Manual

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Instruction Manual

Cisco

Cisco AIR-CAP1552H-x-K9 User manual

Cisco

Cisco WAP571 User manual

Cisco

Cisco WAP200 - Small Business Wireless-G Access... Instruction Manual

Cisco

Cisco WAP121 User manual

Cisco

Cisco AIR-AP1542I-*-K User manual

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... User manual

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... User manual

Cisco

Cisco WAP121 User manual

Cisco

Cisco WAP300N User manual

Cisco

Cisco Meraki CW9162I-MR Manual

Cisco

Cisco AIR-AP1120B-A-K9 - Aironet 1100 Series Access... Manual

Cisco

Cisco Aironet 1200 Series Manual

Cisco

Cisco VEN501 User manual

Cisco

Cisco Meraki MR33 User manual

Popular Wireless Access Point manuals by other brands

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Quick installation guide

Ubiquiti

Ubiquiti NanoStation NSM2 quick start guide

Aruba

Aruba IAP-335 user guide

Advantek Networks

Advantek Networks AWN-AP-54MR user manual

IP-COM

IP-COM AP355 user guide

Buffalo

Buffalo AirStation WLA-L11G user manual

EnGenius

EnGenius EnStationACv2 user manual

D-Link

D-Link DAP-3662 Quick installation guide

xG Technology

xG Technology xMax CN1300 installation guide

Widelink

Widelink ezWave WAP-1100 Series user guide

Edimax

Edimax CAP1200 user manual

Ubiquiti

Ubiquiti LBE-5AC-Gen2 quick start guide

Aruba

Aruba AP-203R installation guide

LuXout Shades

LuXout Shades LUXSHADE MOTION manual

CreatComm

CreatComm TB5F user manual

SineDigital

SineDigital MW-1500AP(H) installation guide

TP-Link

TP-Link AP9650 V1 Quick installation guide

Draytek

Draytek VIGORAP 902 user guide

Reboot and Reset Factory Default Settings on

the WAP131

Objective

The factory default reset erases all configuration settings that have been modified by the

user, and restores the device to its original settings. This may be helpful if you lose the

password to a device and wish to regain access.

Performing a reboot restarts the device with a saved configuration.

The objective of this article is to show you how to reset to factory default settings and how to

reboot a WAP131 Wireless Access Point.

Note: It is advised to save a backup copy of the configuration before beginning this process.

Refer to Download and Backup Configuration Files on the WAP131 and WAP351 for

additional information.

Applicable Devices

• WAP131

Software Version

• 1.0.0.39

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press and hold the Reset button located at the back of the device for approximately

ten seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot. The

Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the Power button to turn off the device. After 10 seconds have passed, press

the Power button a second time to power the device back on. The Access Point reboots and

is refreshed.

Note: The power button will not have any affect if the WAP is being powered with PoE

(Power over Ethernet).

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot. The

Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login page appears. Login with the saved administration credentials.