Cisco MGX 8850 Operator's manual

Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706. USA

Installing Plastic Motherboard Insulator in an

MGX 8850 System

Installing Backplane Plastic Insulating Cover

Use the following procedure to install the insulating cover over a system’s backplane. This procedure

may be done without powering down the system.

Step 1 Open the plastic grill on the front side of the intake plenum, located directly underneath the card cage

or the fan space, using a flat blade screw driver to loosen the two recessed screws. Tilt the plastic grill

forward about 45 degrees, then lift out and set it aside.

Step 2 Hold the plastic cover, shown in the drawing below, so that the 16 short tabs are facing towards you.

43776

3 Tabs

Short tabs

Installing Plastic Motherboard Insulator in an MGX 8850 System

78-10389-01

Step 3 The next illustration shows the clear plastic backplane cover viewed from the bottom toward the top of

the cabinet.

Step 4 Slide the clear plastic backplane cover underneath the card cage and toward the bottom of the

backplane; the flange with the 3 tabs and 2 cutouts will face the backplane.

43777

Underside of chassis

Installing Plastic Motherboard Insulator in an MGX 8850 System

78-10389-01

Step 5 Align the two cutouts on the plastic cover with the two sheetmetal flanges located directly behind the

backplane. Make sure the three tabs on the plastic cover are hooked inside the sheet metal flange.

Warning

A high-energy hazard exist in the system while it is running. Be careful not to let your

fingers or thumb touch the motherboard. Do not wear loose clothing or jewelry, such as

rings, bracelets, or chains while performing this installation.

43777

Underside of chassis

Installing Plastic Motherboard Insulator in an MGX 8850 System

78-10389-01

Step 6 Press the center of the plastic cover to snap the tabs into the card cage perforations as shown in the

illustration below. Keep the plastic cover between your fingers and the motherboard.

Step 7 Continue to press the plastic cover starting from the center then moving to each outside edge to snap

the remaining tabs. You should be able to hear an audible click as these tabs are snapped into place.

Step 8 Replace the plastic grill removed in Step 1 and secure with the two screws using a flat blade screw

driver.

This completes the installation of the plastic insulating cover.

43779

Underside of chassis

Other manuals for MGX 8850

Table of contents

Other Cisco Switch manuals

Cisco

Cisco Nexus C9316D-GX Manual

Cisco

Cisco Meraki MS220 Series User manual

Cisco

Cisco IE 2000 User manual

Cisco

Cisco TrustSec User manual

Cisco

Cisco Catalyst 3550 Manual

Cisco

Cisco LightStream 1010 User manual

Cisco

Cisco Catalyst 4124 Operating and safety instructions

Cisco

Cisco MDS 9100 Series Manual

Cisco

Cisco Catalyst 4500 Series Instruction Manual

Cisco

Cisco Laserjet,Color Laserjet 3020 User instructions

Cisco

Cisco SR2024 - Small Business Unmanaged Switch User manual

Cisco

Cisco Catalyst 3650 Series User manual

Cisco

Cisco 2975 - Catalyst LAN Base Switch User manual

Cisco

Cisco Catalyst 4500 Series Installation guide

Cisco

Cisco IE 3000 Manual

Cisco

Cisco Catalyst 2960S-48FPD-L User manual

Cisco

Cisco AJ732A - MDS 9134 Fabric Switch Instruction Manual

Cisco

Cisco SD205 User manual

Cisco

Cisco Nexus 5000 Series User manual

Cisco

Cisco Catalyst 9400 Series Manual

Cisco

Cisco Aironet 350 Series User manual

Cisco

Cisco Catalyst 2960-L User manual

Cisco

Cisco Nexus 9504 Manual

Cisco

Cisco Catalyst 6816-X-LE Operating and safety instructions

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual