Cisco UCS 5100 Quick guide
Unified Computing System KVM Console Access
to Blade Server Configuration Example
Document ID: 110435
Contents
Introduction
Prerequisites
Requirements
Components Used
Network Diagram
Conventions
Configure
UCS Manager GUI
UCS Manager CLI
Verify
Troubleshoot
Related Information
Introduction
The KVM console is a video over IP representation of the video output on the blade. The KVM console
access to server blades in Cisco UCS is conceptually similar to any industry standard KVM console access to
the blade. This configuration example describes how to access the KVM console from the blade view via the
Unified Computing System (UCS) Manager. Additionally, once the server profile association is complete, you
can access the same KVM console from the Server Profile view as well. The KVM console service is
provided by the blade's BMC and can be accessed via the external IP address only (that is, a pool of external
routable addresses).
In order to use the KVM console to access the blade server, a pool of IP addresses is assigned as a
management interface into the server blades. These IP addresses represent the KVM console access. Note that
these IP addresses need to be externally routable for remote access to the servers via the KVM console.
This configuration example describes how to configure KVM console access to the blade in the Cisco UCS
environment via these methods:
UCS Manager GUI• UCS Manager CLI•
Prerequisites
Requirements
Cisco recommends that you:
Have a working knowledge of Cisco UCS server blade software and hardware.• Be familiar with the UCS management application.• Understand the impact and implications of the different commands described in this document.• Be familiar with the UCS components and topology. Refer to the Network Diagram for a typical
solution.
•
Components Used
The information in this document is based on the Cisco Unified Computing System.
The information in this document was created from the devices in a specific lab environment. All of the
devices used in this document started with a cleared (default) configuration. If your network is live, make sure
that you understand the potential impact of any command.
Network Diagram
A typical Cisco UCS topology is similar to this network diagram:
Conventions
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
Configure
In this section, you are presented with the information to configure the features described in this document.
UCS Manager GUI
Complete these steps in order to use the UCS GUI to configure KVM console access to the blade server:
In the navigation pane, click the Admin tab.1. Expand Communication Services, and choose Management IP Pool (ext−mgmt).2. Click Create Block of IP Addresses.3.
Enter the appropriate information in order to create the block of IP addresses, and then click OK.
Note: The IP addresses in the block must be routable outside.
4.
UCS Manager CLI
Complete these steps in order to use the UCS CLI to configure KVM console access to the blade server:
Enter org mode.1. Enter ip−pool and then ext−mgmt mode.2. Enter the pool ip address block.3. Commit transaction.
Power−A
Power−A#
Power−A#
Power−A#scope org
Power−A /org #scope ip−pool ext−mgmt
Power−A /org/ip−pool #scope pooled 10.193.35.200
4.
Power−A /org/ip−pool/pooled #commit−buffer
Power−A /org/ip−pool/pooled #
Power−A /org/ip−pool/pooled #show detail
Pooled:
IP Address: 10.193.35.200
Subnet: 255.255.255.0
Def Gw: 10.193.35.1
Assigned: Yes
Assigned To: sys/chassis−1/blade−2/mgmt/ipv4−pooled−addr
Power−A /org/ip−pool/pooled #
Verify
Complete these steps in order to verify KVM console access has been configured correctly:
In the navigation pane, click the Equipment tab.1. Expand any chassis on which the blade is installed.2. Expand the Servers tab.3. Select the blade server.4. Click the General tab, and then click KVM Console.
The KVM console should successfully connect to the blade server as shown in this image:
5.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
Technical Support & Documentation − Cisco Systems•
Contacts & Feedback | Help | Site Map
© 2014 − 2015 Cisco Systems, Inc. All rights reserved. Terms & Conditions | Privacy Statement | Cookie Policy | Trademarks of
Cisco Systems, Inc.
Updated: Apr 28, 2010 Document ID: 110435
Other manuals for UCS 5100
6
Table of contents
Other Cisco Server manuals
Cisco
Cisco ONS 15454 Manual
Cisco
Cisco UCS C240 M4 Installation and maintenance instructions
Cisco
Cisco UCS C24 Installation and maintenance instructions
Cisco
Cisco UCS B460 M4 User manual
Cisco
Cisco UCS B200 M4 Installation and operation manual
Cisco
Cisco AS5300 - Universal Access Server User manual
Cisco
Cisco UCS B200 M4 User manual
Cisco
Cisco Unity User manual
Cisco
Cisco UCS B200 M4 Manual
Cisco
Cisco Firepower Management Center 750 User manual
Cisco
Cisco UCS C22 Installation and maintenance instructions
Cisco
Cisco ISE-3315 User manual
Cisco
Cisco UCS C24 Installation and maintenance instructions
Cisco
Cisco ACE-4710-1F-K9 User manual
Cisco
Cisco N20-B6625-1 System manual
Cisco
Cisco B200 M3 User manual
Cisco
Cisco SCE8000 GBE Operator's manual
Cisco
Cisco UCS C220 M3 Installation and maintenance instructions
Cisco
Cisco AS5300 - Universal Access Server User manual
Cisco
Cisco UCS C460 User manual
