Cisco IR1101 User manual
Product Overview
This section contains the following:
•Product Overview, on page 1
•General Description, on page 1
•SKU Information, on page 2
•Cisco IR1101 Series Platform Features, on page 3
•Front Panel Icons and LEDs, on page 12
•Supported Cisco Antennas and Antenna Accessories, on page 14
•Modem Support, on page 14
•Power Supply, on page 17
•RJ45 Ports, on page 18
•Ethernet and Optical SFP Modules, on page 19
•DSL SFP Module, on page 20
Product Overview
This chapter provides an overview of the features available for the Cisco IR1101 Industrial Integrated Services
Router and its Expansion Module. It contains the following sections:
Prior to installing this device read the Regulatory Compliance and Safety Information .
Note
General Description
The Cisco IR1101 Industrial Integrated Services Router is a next generation modular industrial router which
has a base module with additional Pluggable Modules that can be added. The Pluggable Module provides the
flexibility of adding different interfaces to the IR1101 platform, for example, a cellular module.
The IR1101 ISR also has an Expansion Module that adds key capabilities such as dual LTE Pluggables,
mSATA SSD FRU, SFP, and Digital GPIO connections.
Product Overview
1
Figure 1: The IR1101 Industrial Integrated Services Router
SKU Information
The following table lists the different SKUs available for the Cisco IR 1101.
Table 1: Supported SKUs for Cisco IR1101
DescriptionSKU ID
IR1101 Base UnitIR1101-K9
Expansion Module with 1 GE SFP, 1 Pluggable Module, 1 Digital I/O Connector, and 1 mSATA SSD
Slot.
IRM-1100-SPMI
Expansion Module with 1 GE SFP and1 Pluggable Module.IRM-1100-SP
100 GB mSATA SSDIR1100-SSD-100G
Optional AC power adapter with 110/220V AC and 88-300V DC input (Temperature: -40C to 60C)PWR-IE50W-AC
Din rail kit and mounting screws for horizontal and vertical mountingIR1101-DINRAIL(=)
Din rail kit for the Expansion ModuleIRM-1100-DINRAIL
Wall mount kitIR1101-WALLMNT(=)
Product Overview
2
Product Overview
SKU Information
Cisco IR1101 Series Platform Features
This section describes the different components of the router.
Cisco IR1101 Base Router
The following lists the hardware platform features for the Cisco IR1101.
• External Power Entry
• Nominal: 12 to 48VDC
• Absolute min/max: 9.6 to 60VDC
• Typical current: 0.82A to 0.22A
• Maximum current: 0.91A to 0.28A
• 4-pin 3.8 mm EURO power connector
• External Reset/Recovery Push Button
• Gigabit Ethernet Combo RJ45+SFP connector.
• RJ45 connector will support IEEE802.3 Ethernet over copper wiring standards of 10Base-T,
100Base-TX, and 1000Base-T
• SFP port will support 1000Base-X or 100Base-FX Fiber Ethernet standard SFP
• LAN Ports
• 4x RJ45 10/100 Fast Ethernet
• Serial Port
• 1 x RJ45 RS232 Port (DTE)
• USB Ports
• 1x USB 2.0 Type A Host Port
• 1x USB 2.0 mini USB Type B console port
• Compliance
• Class A EMC or better
• IP30 compliant when vertical and ports downward
• Industrial temperature [-40ºC to +60ºC, 13.8Kft (operating), 15Kft (non-operating)]
• One alarm input
The following graphic shows the IR1101 ISR base router.
Product Overview
3
Product Overview
Cisco IR1101 Series Platform Features
Figure 2: Cisco IR1101 Industrial Integrated Services Router
The following graphics show the IR1101 Base Module Front.
Figure 3: Cisco IR1101 Integrated Services Router with USB covers in place
DetailsItem
USB 2.0 Port Cover1
Mini-USB Console Cover2
Product Overview
4
Product Overview
Cisco IR1101 Base Router
The following graphic shows the front panel details of the Cisco IR1101.
Figure 4: Cisco IR1101 Front Panel
Table 2:
SFP GE WAN1
USB 2.02
RJ45 GE WAN3
Serial Port4
FE LAN Ports 1-45
Grounding Point (on side of device)6
DC Power and Alarm Input7
Mini-USB Console8
Reset Button9
Pluggable Module10
Cisco IRM-1100-SPMI Expansion Module
The following graphic shows the IR-1100-SPMI Expansion Module.
Product Overview
5
Product Overview
Cisco IRM-1100-SPMI Expansion Module
Figure 5: IR-1100-SPMI Expansion Module
The following lists the hardware platform features for the Cisco IR-1100-SPMI:
• 1 GE SFP
• 1 Pluggable slot
• 1 Digital I/O connector
• 1 mSATA SSD slot
Figure 6: IR-1100-SPMI Expansion Module Details
Product Overview
6
Product Overview
Cisco IRM-1100-SPMI Expansion Module
4 GPIO + 1 Return (Digital I/O)1
SFP Connector2
Pluggable Module3
mSATA SSD Slot4
Digital I/O LEDs5
Digital I/O Connector
The Digital I/O connector has 4 GPIO connections plus 1 Return connection. The Digital I/O supports Both
Dry and Wet contacts up to 60Volts.
• Dry contact is isolated from a voltage source (or “No Volt”), with an embedded relay function (NPN
transistor), usually used to indicate an event. For example: open/close, alarm.
• Wet contact is a contact with external power (+3.3V to +60V, max 150mA of current allowed at high
voltage) applied, usually used to energize something. For example: solenoid, light.
The following graphic shows the connector.
Digital I/O is only supported on IOS-XE version 16.12.1 and above.
Note
The default state of the Digital I/O is input, the open-collector is open (off).
Note
Figure 7: Digital I/O connector
The pinouts for the Digital I/O are described in the following table.
Table 3: Digital I/O Pinouts
DescriptionDirectionNamePin
#
Digital IO 1I/ODIO11
Digital IO 2I/ODIO22
Digital IO 3I/ODIO33
Product Overview
7
Product Overview
Digital I/O Connector
DescriptionDirectionNamePin
#
Digital IO 4I/ODIO44
Digital IO Common ReturnReturnReturn5
Digital Input and Output Specifications are described in the following tables.
Digital Input Specification is considered “dry contact”, and Digital Output Specification is considered “wet
contact”.
Table 4: Digital Input Specification
UnitMaximumMinimumSpecification
Volts602.2Input Voltage High
Volts1.2-Input Voltage Low
uA0.68mA
Note1
-Input Current
Note1: Current is flowing out of the terminal although it is an input, i.e. sourcing. The current is flowing in
the terminal for the output, i.e. sinking.
Table 5: Digital Output Specification
NotesUnitMaximumMinimumSpecification
No external voltage
applied.
Volts2.5Output Voltage High
No external voltage
applied.
Volts0.4-Output Voltage Low
Ohms3.3K – 1%3.3K – 1%Internal Pull-up
Resistance
Volts3-Internal Pull-up Voltage
External resistance
required to limit current
to 200mA.
Volts603.3External Pull-up Voltage
mA200Sink Current
Common features of the Digital I/O are:
• Withstands up to 60V applied at the terminal.
• Reverse voltage protected and causes no damage to the equipment.
• Digital input and output can coexist on different channel.
Product Overview
8
Product Overview
Digital I/O Connector
• LED Indicator: provision-able, On: Active, Off: Non-active.
• Electrical isolation: 2000 VDC.
• 4kV Surge protected (IEC 61000-4-5).
IR-1100-SPMI Expansion Module LEDs
There are 6 LEDs in the Expansion Module. Four LEDs show the status of digital input and output. One LED
shows the SFP port status and one LED shows the mSATA status. The LED behavior is shown in the following
table.
Table 6: Expansion Module LEDs
DefinitionLED
Off - InactiveSolid Yellow- ActiveDigital I/O as Input
Off - InactiveSolid Yellow- ActiveDigital I/O as Output
Off - No LinkSolid Yellow - Port link with no activityFlashing Yellow - Port link healthy with activitySFP
Off - Not powered on or no activityFlashing Green - mSATA being accessedmSATA
Cisco IR-1100-SP Expansion Module
The IR-1100-SP Expansion Module is the same as the IR-1100-SPMI module, without the Digital I/O and
mSATA components.
The following lists the hardware platform features for the Cisco IR-1100-SP:
• 1 GE SFP (see the supported list of SFP’s here: SFP Module, page 26 )
• 1 Pluggable slot
Cisco Pluggable Module
The Pluggable Module provides the flexibility of adding different interfaces to the IR1101 platform, for
example, a cellular module.
Pluggable LTE Module
Highlights of the LTE Pluggable Module are:
• All Cellular interfaces are supported through a Pluggable Module
• Micro-Sim, 3FF size. Cisco recommends Industrial Temp micro SIMs that are rated from -40C to +105C.
The following two figures show an example of a Pluggable Module. In this case, the LTE Pluggable Module.
Product Overview
9
Product Overview
IR-1100-SPMI Expansion Module LEDs
Figure 8: LTE Pluggable Module (front)
LTE-Main SMA1
GPS SMA2
Micro USB Debug Port3
LTE-Div SMA4
Figure 9: LTE Pluggable Module (with antennas)
LTE Category 18 Pluggable Module
This module has a new smaller form factor SMA Diversity Antenna for usability and Micro-USB port access.
Product Overview
10
Product Overview
LTE Category 18 Pluggable Module
Other manuals for IR1101
4
Table of contents
Other Cisco Network Router manuals
Cisco
Cisco ASR 1000 series Manual
Cisco
Cisco WUMC710 User manual
Cisco
Cisco Network Convergence System 6000 Series User manual
Cisco
Cisco DVB CAR100 Series User manual
Cisco
Cisco 1905 Instruction Manual
Cisco
Cisco Cisco 760 Series User manual
Cisco
Cisco WRT54GR User manual
Cisco
Cisco 867VAE-W User manual
Cisco
Cisco ASR 5500 User manual
Cisco
Cisco CVR100W User manual
Cisco
Cisco NCS 540 Series User manual
Cisco
Cisco ASR 9001 Manual
Cisco
Cisco 3825 Series Quick start guide
Cisco
Cisco 2821 Series Quick start guide
Cisco
Cisco CVR100W User manual
Cisco
Cisco 10008 User manual
Cisco
Cisco 860 Series Instruction Manual
Cisco
Cisco 7304 Series Operating and maintenance instructions
Cisco
Cisco 8201 User manual
Cisco
Cisco NCS 540 Series Manual
