Cisco 8201 User manual

Replace Chassis Components

•Replace Fan Modules for Cisco 8201 Routers, on page 1

•Replace Power Supply, on page 3

Replace Fan Modules for Cisco 8201 Routers

The fan module is designed to be removed and replaced while the system is operating without presenting an

electrical hazard or damage to the system. Please keep the replacement fan modules ready prior to attempting

this task.

The routers support FAN-1RU-PI (port-side intake airflow) and FAN-1RU-PE (port-side exhaust airflow)

fan modules.

Note

The airflow direction must be the same for all power supply and fan modules in the chassis.

Note

Step 1 To remove a fan module, follow these steps:

a) Press two latches on the fan module and grasp the handle of fan module.

Replace Chassis Components

Figure 1: Cisco 8201 Router —Remove Fans

Latched fan module1

b) As you simultaneously press the latches pull the fan module fully out of the chassis.

Step 2 To install a fan module, follow these steps:

a) Hold the fan module with the LED at the top.

b) Align the fan module to the open fan tray slot in the chassis, and press the module all the way into the slot until the

left and right latches click and are locked on the chassis.

Replace Chassis Components

Replace Fan Modules for Cisco 8201 Routers

If the fan module does not go all the way into the slot, do not force it. Remove the fan module and verify

that it is the correct type for your router and in the correct orientation. To verify the status of fans and the

speed, use the show environment fan command.

Note

c) If the chassis is powered on, listen for the sound of the fans in operation. You should immediately hear them in

operation. If you do not hear them, ensure that the fan module is inserted completely in the chassis.

During the fan module replacement, the other fans adjust their speed to allow for proper initialization of

the new module. When you insert a new fan module, the fans may run at lower or higher speeds for a few

minutes.

Note

d) Verify that the fan module LED is green. If the LED is not green, one or more fans are faulty. If this situation occurs,

contact your customer service representative for replacement parts.

Replace Power Supply

Use this procedure to replace the AC or DC power supply units. Be sure to power down the fixed configuration

PDU (power distribution unit) before removing it from the chassis.

Step 1 If the power supply is connected to a AC or DC circuit, shut off the circuit at the circuit breaker.

Step 2 Disconnect the PSU cable.

Step 3 Press the tab inward to unlatch the PSU, and pull the handle to remove the PSU.

Step 4 Insert the new PSU.

If the PSU does not go all the way into the slot, do not force it. Remove the PSU and verify that it is the correct

type for your router and in the correct orientation.

Note

Step 5 Connect the PSU cable.

Step 6 If the power supply is connected to a DC circuit, turn on the circuit breaker for the DC power source. After replacing the

PSU, verify the power using the show environment power command.

Replace Chassis Components

Replace Power Supply

Figure 2: Cisco 8201 Router —Remove Power Supply

Power supply1

Replace Chassis Components

Replace Power Supply

Table of contents

Other Cisco Network Router manuals

Cisco

Cisco Catalyst 2928 User manual

Cisco

Cisco XR 12000 Service manual

Cisco

Cisco 1700 series Installation guide

Cisco

Cisco 2610XM Quick guide

Cisco

Cisco CRS-1 - Carrier Routing System Router User manual

Cisco

Cisco uBR925 Setup guide

Cisco

Cisco 7000 and 7507 LED Board MAS-7KLED Guide

Cisco

Cisco 807 Manual

Cisco

Cisco SGE2000 Instruction Manual

Cisco

Cisco 7600 Series Manual

Cisco

Cisco 8800 Series Manual

Cisco

Cisco NCS 5500 Series User manual

Cisco

Cisco 12006 series Operating and safety instructions

Cisco

Cisco Internet Router Cisco 12404 User manual

Cisco

Cisco WET54G User manual

Cisco

Cisco NCS 5500 Series Instruction Manual

Cisco

Cisco 2501 - Router - EN User manual

Cisco

Cisco 10000 Series User manual

Cisco

Cisco Linksys EA2700 User manual

Cisco

Cisco 2821 - Integrated Services Router Unified Communications... Quick guide

Cisco

Cisco 12008 Operator's manual

Cisco

Cisco RV130 User manual

Cisco

Cisco ASR 9901 User manual

Cisco

Cisco WRT150N User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

EnGenius

EnGenius ESR-9710 quick start guide

LevelOne

LevelOne FBR-1416 user manual

Dynacord

Dynacord Promatrix 6000 Operation manual

Lorex

Lorex F5D8230-4 Guide